Chemical Engineering / Kimya Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/14
Browse
3 results
Search Results
Now showing 1 - 3 of 3
Article Citation - WoS: 4Citation - Scopus: 5Breakthrough Curve Analysis of Phosphorylated Hazelnut Shell Waste in Column Operation for Continuous Harvesting of Lithium From Water(Elsevier, 2024) Recepoğlu, Yaşar Kemal; Arar, Ozguer; Yuksel, AsliIn batch-scale operations, biosorption employing phosphorylated hazelnut shell waste (FHS) revealed excellent lithium removal and recovery efficiency. Scaling up and implementing packed bed column systems necessitates further design and performance optimization. Lithium biosorption via FHS was investigated utilizing a continuous-flow packed-bed column operated under various flow rates and bed heights to remove Li to ultra-low levels and recover it. The Li biosorption capacity of the FHS column was unaffected by the bed height, however, when the flow rate was increased, the capacity of the FHS column decreased. The breakthrough time, exhaustion time, and uptake capacity of the column bed increased with increasing column bed height, whereas they decreased with increasing influent flow rate. At flow rates of 0.25, 0.5, and 1.0 mL/min, bed volumes (BVs, mL solution/mL biosorbent) at the breakthrough point were found to be 477, 369, and 347, respectively, with the required BVs for total saturation point of 941, 911, and 829, while the total capacity was calculated as 22.29, 20.07, and 17.69 mg Li/g sorbent. In the 1.0, 1.5, and 2.0 cm height columns filled with FHS, the breakthrough times were 282, 366, and 433 min, respectively, whereas the periods required for saturation were 781, 897, and 1033 min. The three conventional breakthrough models of the Thomas, Yoon-Nelson, and Modified Dose-Response (MDR) were used to properly estimate the whole breakthrough behavior of the FHS column and the characteristic model parameters. Li's extremely favorable separation utilizing FHS was evidenced by the steep S-shape of the breakthrough curves for both parameters flow rate and bed height. The reusability of FHS was demonstrated by operating the packed bed column in multi-cycle mode, with no appreciable loss in column performance.Article Citation - WoS: 13Citation - Scopus: 12Comparison of Photocatalytic Performances of Solar-Driven Hybrid Catalysts for Hydrogen Energy Evolution From 1,8–diazabicyclo[5.4.0]undec-7 (dbu) Solution(Elsevier, 2022) Orak, Ceren; Yüksel, AslıHydrogen is evolved from 1,8–Diazabicyclo [5.4.0]undec-7-ene (DBU) model solution which is a nitrogen-containing heterocyclic organic compound using different solar-driven hybrid photocatalysts. A characterization study is performed and the results of PL analysis show that the most promising solar-driven hybrid catalyst is graphene supported LaFeO3. Then, an experimental design matrix is built using the Box Behnken model to main and interaction effects of reaction parameters (pH, catalyst loading, and [H2O2]0). Based on the experimental results relatively higher hydrogen amounts are achieved using GLFO and this finding is supported by PL analysis. The highest hydrogen amount and DBU removal are determined as 3058.31 μmol/gcat and 90.3%, respectively. Statistical analysis shows that the square of catalyst loading is the only effective parameter over the produced hydrogen amount from the DBU model solution using GLFO and the R2 of model is 92.47%. Thus, hydrogen production and wastewater treatment could be achieved via photocatalytic oxidation as concomitant.Article Citation - WoS: 31Citation - Scopus: 38Liquefaction of Waste Hazelnut Shell by Using Sub- and Supercritical Solvents as a Reaction Medium(Elsevier, 2019) Demirkaya, Emre; Dal, Orkan; Yüksel, AslıDirect thermochemical biomass degradation to obtain bio-oil by using organic solvents is not a new process type, and it has some advantages over hydrothermal liquefaction technique. However, up to our best knowledge, in this study, hazelnut shell decomposition by using ethanol, acetone and their mixtures at sub/supercritical conditions was studied for the first time in literature. Experiments were carried out between 220-300 degrees C, at three different reaction times (30, 60 and 90 min) for five different solvent ratios. Highest solid conversion achieved at 300 degrees C by using pure ethanol was 64.2%, whereas highest bio-oil yield was found as 44.2% at 300 degrees C with 50/50 (EtOH/Ac: v/v). Ethanol and acetone showed different characteristics during the reactions and their effects on the conversion and bio-oil yield were discussed. Statistical analysis showed that time, temperature, ratio and synergy between temperature-time were affecting parameters for the conversion and bio-oil yield. (C) 2019 Elsevier B.V. All rights reserved.