Materials Science and Engineering / Malzeme Bilimi ve Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4719
Browse
3 results
Search Results
Book Part Citation - Scopus: 1A Recycling Route of Plastics Via Electrospinning: From Daily Wastes To Functional Fibers(Walter de Gruyter GmbH, 2019) Isık, Tuğba; Isık, Tuğba; Horzum,N.; Demir, Mustafa Muammer; Demir, Mustafa Muammer; 03.09. Department of Materials Science and Engineering; 03. Faculty of Engineering; 01. Izmir Institute of TechnologySince large-scale plastic production has begun in the 1940s, plastics have been produced and used globally, bringing many advantages to modern life. The consumption of plastics has increased exponentially due to their low cost, chemical resistance, lightness, durability and ability to combine with other materials. However, plastic materials represent high tonnage in urban wastes, and it is known that these plastics discarded at the end of their useful life by filling the landfill sites. Electrospinning is a well-established and versatile technique for the fabrication of submicron fibers. In addition, it is a promising approach for the recycling of waste polymers without using complex methodologies. In this chapter, utilization of electrospinning approach for the recycling of daily wastes will be discussed. The literature about the daily wastes of both synthetic materials and natural/agricultural materials will be analyzed, and the applications of these materials will be given in detail. © 2019 Walter de Gruyter GmbH, Berlin/Boston. All rights reserved.Article Citation - WoS: 5Citation - Scopus: 4Influence of Partitioning Treatment on Microstructure and Mechanical Properties of an Alloyed Ductile Iron Austempered at Different Temperatures(Walter de Gruyter GmbH, 2023) Neite, Maximilian; Davut, Kemal; Nalçacı, Burak; Davut, Kemal; Erdoğan, Mehmet; 03.09. Department of Materials Science and Engineering; 03. Faculty of Engineering; 01. Izmir Institute of TechnologyThe present study was conducted to uncover effects of partitioning treatment on Cu-Ni-Mo alloyed ductile iron (DI) austempered at different temperatures. For this purpose, the DI samples, produced via sand casting, were austenitized at 900 °C for 60 min, followed by austempering at the temperatures of 275-325-375 °C for 120 min and afterwards a partitioning treatment was applied at 200 °C for 15 min. In the characterization studies, dilatometer, image analysis, JMat-Pro, mechanical tests, XRD, optical microscope, and scanning electron microscope (SEM) equipped with EBSD detector were utilized. Characterization studies showed that the effects of partitioning treatment were directly correlated with austempering temperature and high carbon austenite volume fraction changed in the range of 19.48-35.45%. That redistribution of carbon (C) between bainitic ferrite and high carbon austenite occurred, in turn, the carbon content of high carbon austenite increased with the partitioning treatment irrespective of austempering temperature were uncovered. Furthermore, the partitioning treatment considerably changed the grain morphologies of both high carbon austenite and banitic ferrite. As a consequence of these microstructural differences, the highest tensile strength of 1489.2 MPa was established in the sample austempered at 275 °C and partitioned at 200 °C, whereas the highest ductility of 5.61% acquired at the austempering temperature of 375 °C. © 2023 Walter de Gruyter GmbH, Berlin/Boston.Article Citation - WoS: 3Citation - Scopus: 3Nondestructive Microstructural Characterization of Austempered Ductile Iron(Walter de Gruyter GmbH, 2023) Tüzün, Mert Yağız; Davut, Kemal; Yalçın, Mustafa Alp; Davut, Kemal; Kılıçlı, Volkan; 03.09. Department of Materials Science and Engineering; 03. Faculty of Engineering; 01. Izmir Institute of TechnologyAustempered ductile iron (ADI) has been preferred in a wide range of applications due its unique combination of high strength, good ductility, wear resistance and fracture toughness together with lower cost and lower density compared to steels. Magnetic Barkhausen noise (MBN) measurement offers a better alternative to traditional characterization techniques by being fast and non-destructive. A simple linear regression using only one single independent variable cannot correlate the MBN with the microstructure of ADI, since its microstructure is multi component. Multiple linear regression analysis (MLRA) was used to build a model that uses the characteristic features of microstructural constituents as input parameters to predict the MBN. For that purpose, Cu-Ni-Mo alloyed ductile iron samples austempered between 325 and 400 degrees C and for 45-180 min duration were used. The results show that MBN is most sensitive to the size and shape of acicular ferrite and retained austenite. Moreover, MBN is almost insensitive to the size, morphology and volume fraction of graphite particles. This indicates that retained austenite pins the domain walls more effectively than the graphite particles. Considering the results MLRA, MBN technique can be used to characterize the ausferritic microstructure of ADI.