Materials Science and Engineering / Malzeme Bilimi ve Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4719
Browse
37 results
Search Results
Article Citation - Scopus: 1Oxidizer Gases Effects on the Diameter-Controlled Synthesis of Carbon Nanotubes(MIM Research Group, 2021) İnce Yardımcı, Atike; Öğütlü, Ahmet Sabri; Öğütlü, DenizIn this study, the influence of the oxidizers on the synthesis of carbon nanotubes by C2H4 decomposition over Fe catalyst has been investigated. CO2, O2, and H2O have been used as oxidizers, and to control catalyst particle formation and their sizes in the pretreatment stage. The same oxidizers have also been used in the growth stage to maintain the catalyst particle size, remove amorphous carbon formation to keep catalyst particle active. The results of scanning electron microscopy indicated that the average diameters of nanotubes decreased from 13.4±1.2 nm to 6.2±0.5 nm and extremely dense nanotubes were obtained when we added a small amount of CO2. Adding O2 extremely decreased the areal carbon nanotube density while widens the diameter distribution. H2O addition resulted in larger average diameters and made the growth strongly pretreatment dependent. Within the parameters tried for catalyst pretreatment and CNT growth processes, CO2 seemed the best choice for a weak oxidizing assistant. The strong dependency of the average diameter on pretreatment conditions indicated that pretreatment is a very important step in deciding the final diameters and their distribution.Article Citation - WoS: 14Citation - Scopus: 17Enhancement of Thermoelectric Efficiency of T-Hfse2 Via Nanostructuring(American Physical Society, 2021) Ünsal, Elif; Senger, Ramazan Tuğrul; Sevinçli, HaldunIn this work, ab initio calculations based on density functional theory and the Landauer formalism are carried out to investigate ballistic thermoelectric properties of T-HfSe2 nanoribbons (NRs). The zigzag-edged NRs are metallic, and they are not included in this study. The armchair NRs possess two types of edge symmetries depending on the number of atoms present in a row; odd-numbered NRs have mirror symmetry, whereas the even-numbered NRs have glide reflection symmetry. The armchair-edged NRs are dynamically stable and show semiconducting properties with varying band gap values in the infrared and visible regions. Detailed transport analyses show that the n-type Seebeck coefficient and the power factor differ because of the structural symmetry, whereas the p-type thermoelectric coefficients are not significantly influenced. It is shown that the phonon thermal conductance is reduced to a third of its two-dimensional value via nanostructuring. The p-type Seebeck coefficient and the power factor for T-phase HfSe(2 )are enhanced in NRs. We report that the p-type ZT value of HfSe2 NRs at 300 and 800 K are enhanced by factors of 4 and 3, respectively.Article Citation - WoS: 12Citation - Scopus: 14Laser Assisted Synthesis of Anisotropic Metal Nanocrystals and Strong Light-Matter Coupling in Decahedral Bimetallic Nanocrystals(Royal Society of Chemistry, 2021) Mert Balcı, Fadime; Sarısözen, Sema; Polat, Nahit; Güvenç, Çetin Meriç; Karadeniz, Uğur; Tertemiz, Necip Ayhan; Balcı, SinanThe advances in colloid chemistry and nanofabrication allowed us to synthesize noble monometallic and bimetallic nanocrystals with tunable optical properties in the visible and near infrared region of the electromagnetic spectrum. In the strong coupling regime, surface plasmon polaritons (SPPs) of metal nanoparticles interact with excitons of quantum dots or organic dyes and plasmon-exciton hybrid states called plexcitons are formed. Until now, various shaped metal nanoparticles such as nanorods, core-shell nanoparticles, hollow nanoparticles, nanoprisms, nanodisks, nanorings, and nanobipyramids have been synthesized to generate plasmon-exciton mixed states. However, in order to boost plasmon-exciton interaction at nanoscale dimensions and expand the application of plexcitonic nanocrystals in a variety of fields such as solar cells, light emitting diodes, and nanolasers, new plexcitonic nanocrystals with outstanding optical and chemical properties remain a key goal and challenge. Here we report laser-assisted synthesis of decahedral shaped noble metal nanocrystals, tuning optical properties of the decahedral shaped nanocrystals by galvanic replacement reactions, colloidal synthesis of bimetallic decahedral shaped plexcitonic nanocrystals, and strong plasmon-plasmon interaction in bimetallic decahedral shaped noble metal nanocrystals near a metal film. We photochemically synthesize decahedral Ag nanoparticles from spherical silver nanoparticles by using a 488 nm laser. The laser assisted synthesis of silver nanoparticles yields decahedral (bicolored) and prism (monocolored) shaped silver nanocrystals. The decahedral shaped nanoparticles were selectively separated from prism shaped nanoparticles by centrifugation. The optical properties of decahedral nanocrystals were tuned by the galvanic replacement reaction between gold ions and silver atoms. Excitons of J-aggregate dyes and SPPs of decahedral bimetallic nanoparticles strongly couple and hence decahedral shaped plexcitonic nanoparticles are prepared. In addition, localized SPPs of decahedral shaped bimetallic nanocrystals interact strongly with the propagating SPPs of a flat silver film and hence new hybrid plasmonic modes (plasmonic nanocavities) are generated. The experimental results are further fully corroborated by theoretical calculations including decahedral shaped plexcitonic nanoparticles and decahedral nanoparticles coupled to flat metal films.Article Citation - WoS: 11Citation - Scopus: 13Effect of Cnt Incorporation on Pan/Ppy Nanofibers Synthesized by Electrospinning Method(TÜBİTAK, 2020) İnce Yardımcı, Atike; Tanoğlu, Metin; Yılmaz, Selahattin; Selamet, YusufIn this study, carbon nanotubes (CNTs) added polyacrylonitrile/polypyrrole (PAN/PPy) electrospun nanofibers were produced. Average diameters of the nanofibers were measured as 268 and 153 nm for 10 and 25 wt% of PPy contents, respectively. A relatively higher strain to failure values (23.3%) were observed for the low PPy content. When as-grown CNTs (1 and 4 wt%) were added into the PAN/PPy blends, disordered nanofibers were observed to form within the microstructure. To improve the interfacial properties of CNTs/PAN/PPy composites, CNTs were functionalized with H2SO4/HNO3/HCl solution. The functionalized CNTs were well dispersed within the nanofibers and aligned along the direction of nanofibers. Therefore, beads formation on nanofibers decreased. The impedance of the nanofibers was found to decrease with the PPy content and CNT addition. These nanofibers had a great potential to be used as an electrochemical actuator or a tissue engineering scaffold.Article Citation - WoS: 85Citation - Scopus: 91Ballistic Thermoelectric Properties of Monolayer Semiconducting Transition Metal Dichalcogenides and Oxides(American Physical Society, 2019) Özbal, Gözde; Senger, Ramazan Tuğrul; Sevik, Cem; Sevinçli, HaldunCombining first-principles calculations with Landauer-Mittiker formalism, ballistic thermoelectric transport properties of semiconducting two-dimensional transition metal dichalcogenides (TMDs) and oxides (TMOs) (namely MX2 with M = Cr, Mo, W, Ti, Zr, Hf; X = O, S, Se, Te) are investigated in their 2H and 1T phases. Having computed structural, as well as ballistic electronic and phononic transport properties for all structures, we report the thermoelectric properties of the semiconducting ones. We find that 2H phases of four of the studied structures have very promising thermoelectric properties, unlike their 1T phases. The maximum room temperature p-type thermoelectric figure of merit (ZT) of 1.57 is obtained for 2H-HfSe2, which can be as high as 3.30 at T = 800 K. Additionally, 2H-ZrSe2, 2H-ZrTe2, and 2H-HfS2 have considerable ZT values (both nand p-type), that are above 1 at room temperature. The 1T phases of Zr and Hf-based oxides possess relatively high power factors, however their high lattice thermal conductance values limit their ZT values to below 1 at room temperature.Article Citation - WoS: 1Citation - Scopus: 1Directed Growth of Hydrogen Lines on Graphene: High-Throughput Simulations Powered by Evolutionary Algorithm(American Physical Society, 2018) Özbal, Gözde; Falkenberg, J. T.; Brandbyge, M.; Senger, Ramazan Tuğrul; Sevinçli, HaldunWe set up an evolutionary algorithm combined with density functional tight-binding calculations to investigate hydrogen adsorption on flat graphene and graphene monolayers curved over substrate steps. During the evolution, candidates for the new generations are created by adsorption of an additional hydrogen atom to the stable configurations of the previous generation, where a mutation mechanism is also incorporated. Afterwards a two-stage selection procedure is employed. Selected candidates act as the parents of the next generation. The evolutionary algorithm predicts formation of lines of hydrogen atoms on flat graphene. In curved graphene, the evolution follows a similar path except for a new mechanism, which aligns hydrogen atoms on the line of minimum curvature. The mechanism is due to the increased chemical reactivity of graphene along the minimum radius of curvature line (MRCL) and to sp(3) bond angles being commensurate with the kinked geometry of hydrogenated graphene at the substrate edge. As a result, the reaction barrier is reduced considerably along the MRCL and hydrogenation continues like a mechanical chain reaction. This growth mechanism enables lines of hydrogen atoms along the MRCL, which has the potential to overcome substrate or rippling effects and could make it possible to define edges or nanoribbons without actually cutting the material.Article Citation - WoS: 9Citation - Scopus: 7Epitaxial Characteristics of Mbe-Grown Znte Thin Films on Gaas (211)b Substrates(Springer, 2019) Özçeri, Elif; Tarhan, EnverHighly crystalline ZnTe thin films were grown on GaAs (211)B substrates by molecular beam epitaxy (MBE) for potential applications such as MCT detectors and optoelectronic devices. We investigated the effects of Te to Zn (VI/II) flux ratio on the quality of ZnTe films in terms of crystal orientation, elemental composition, surface roughness, and dislocation density. Atomic concentrations of Zn, Te, and oxygen complexes due to oxygen contamination on the film surfaces were analyzed by X-ray photoelectron spectroscopy. X-ray double crystal rocking curve full width half maximum (FWHM) of ZnTe (422) peak was observed as 233 arcseconds for a 1.66 mu m thick film, which indicates high crystallinity. Wet chemical etching was applied to the films to quantify the crystal quality by calculating etch pit densities (EPD) from scanning electron microscope images. A very low EPD value of 1.7 x 10(7) cm(-2) was measured. Additionally, the root mean square roughness values, obtained from atomic force microscopy topography images were in the range of 10-25 nm. These values were supported by FWHM values of red green blue color intensity histograms obtained from Nomarski Microscope images. The results of our analyses indicate that the VI/II flux ratios of 4 and 4.5 produce the best quality ZnTe films on GaAs (211)B substrates.Article Citation - WoS: 9Structural, Electronic, and Magnetic Properties of Point Defects in Polyaniline (c3n) and Graphene Monolayers: a Comparative Study(American Institute of Physics, 2020) Sevim, Koray; Sevinçli, HaldunThe newly synthesized two-dimensional polyaniline (C3N) is structurally similar to graphene and has interesting electronic, magnetic, optical, and thermal properties. Motivated by the fact that point defects in graphene give rise to interesting features, like magnetization in an all carbon material, we perform density functional theory calculations to investigate vacancy and Stone-Wales type point defects in monolayer C3N. We compare and contrast the structural, electronic, and magnetic properties of these defects with those in graphene. While monovacancies and Stone-Wales defects of C3N result in reconstructions similar to those in graphene, divacancies display dissimilar geometrical features. Different from graphene, all vacancies in C3N have metallic character because of altered stoichiometry; those that have low-coordinated atoms have finite magnetic moments. We further investigate the robustness of the reconstructed structures and the changes in the magnetic moments by applying tensile and compressive biaxial strain. We find that, with the advantage of finite bandgap, point defects in C3N are qualified as good candidates for future spintronics applications.Article Citation - WoS: 12Citation - Scopus: 15Magnetic Mechanism for the Biological Functioning of Hemoglobin(Nature Publishing Group, 2020) Mayda, Selma; Kandemir, Zafer; Bulut, Nejat; Maekawa, SadamichiThe role of magnetism in the biological functioning of hemoglobin has been debated since its discovery by Pauling and Coryell in 1936. The hemoglobin molecule contains four heme groups each having a porphyrin layer with a Fe ion at the center. Here, we present combined density-functional theory and quantum Monte Carlo calculations for an effective model of Fe in a heme cluster. In comparison with these calculations, we analyze the experimental data on human adult hemoglobin (HbA) from the magnetic susceptibility, Mossbauer and magnetic circular dichroism (MCD) measurements. In both the deoxygenated (deoxy) and the oxygenated (oxy) cases, we show that local magnetic moments develop in the porphyrin layer with antiferromagnetic coupling to the Fe moment. Our calculations reproduce the magnetic susceptibility measurements on deoxy and oxy-HbA. For deoxy-HbA, we show that the anomalous MCD signal in the UV region is an experimental evidence for the presence of antiferromagnetic Fe-porphyrin correlations. The functional properties of hemoglobin such as the binding of O-2, the Bohr effect and the cooperativity are explained based on the magnetic correlations. This analysis suggests that magnetism could be involved in the functioning of hemoglobin.Article Citation - WoS: 5Citation - Scopus: 5Collapse of the Vacuum in Hexagonal Graphene Quantum Dots: a Comparative Study Between Tight-Binding and Mean-Field Hubbard Models(American Physical Society, 2020) Polat, Mustafa; Sevinçli, Haldun; Güçlü, Alev DevrimIn this paper, we perform a systematic study on the electronic, magnetic, and transport properties of the hexagonal graphene quantum dots (GQDs) with armchair edges in the presence of a charged impurity using two different configurations: (1) a central Coulomb potential and (2) a positively charged carbon vacancy. The tight-binding and the half-filled extended Hubbard models are numerically solved and compared with each other in order to reveal the effect of electron interactions and system sizes. Numerical results point out that off-site Coulomb repulsion leads to an increase in the critical coupling constant to beta(c) = 0.6 for a central Coulomb potential. This critical value of beta is found to be independent of the GQD size, reflecting its universality even in the presence of electron-electron interactions. In addition, a sudden downshift in the transmission peaks shows a clear signature of the transition from subcritical beta < beta(c) to the supercritical beta > beta(c) regime. On the other hand, for a positively charged vacancy, collapse of the lowest bound state occurs at beta(c) = 0.7 for the interacting case. Interestingly, the local magnetic moment, induced by a bare carbon vacancy, is totally quenched when the vacancy is subcritically charged, whereas the valley splittings in electron and hole channels continue to exist in both regimes.