Materials Science and Engineering / Malzeme Bilimi ve Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4719
Browse
81 results
Filters
Settings
Search Results
Article Citation - WoS: 7Citation - Scopus: 7Breaking the Boundaries of the Goldschmidt Tolerance Factor With Ethylammonium Lead Iodide Perovskite Nanocrystals(American Chemical Society, 2024) Güvenç, Çetin Meriç; Toso, Stefano; Ivanov, Yurii P.; Saleh, Gabriele; Balcı, Sinan; Divitini, Giorgio; Manna, LiberatoWe report the synthesis of ethylammonium lead iodide (EAPbI3) colloidal nanocrystals as another member of the lead halide perovskites family. The insertion of an unusually large A-cation (274 pm in diameter) in the perovskite structure, hitherto considered unlikely due to the unfavorable Goldschmidt tolerance factor, results in a significantly larger lattice parameter compared to the Cs-, methylammonium- and formamidinium-based lead halide perovskite homologues. As a consequence, EAPbI3 nanocrystals are highly unstable, evolving to a nonperovskite delta-EAPbI3 polymorph within 1 day. Also, EAPbI3 nanocrystals are very sensitive to electron irradiation and quickly degrade to PbI2 upon exposure to the electron beam, following a mechanism similar to that of other hybrid lead iodide perovskites (although degradation can be reduced by partially replacing the EA+ ions with Cs+ ions). Interestingly, in some cases during this degradation the formation of an epitaxial interface between (EA x Cs1-x )PbI3 and PbI2 is observed. The photoluminescence emission of the EAPbI3 perovskite nanocrystals, albeit being characterized by a low quantum yield (similar to 1%), can be tuned in the 664-690 nm range by regulating their size during the synthesis. The emission efficiency can be improved upon partial alloying at the A site with Cs+ or formamidinium cations. Furthermore, the morphology of the EAPbI3 nanocrystals can be chosen to be either nanocube or nanoplatelet, depending on the synthesis conditions.Article Citation - WoS: 11Citation - Scopus: 13Magnesium-Ion Battery Anode From Polymer-Derived Sioc Nanobeads(Wiley, 2023) Guo, Wuqi; Kober, Delf; Gurlo, Aleksander; Bekheet, Maged F.; İçin, Öykü; Ahmetoğlu, Çekdar VakıfTin-containing silicon oxycarbide (SiOC/Sn) nanobeads are synthesized with different carbon/tin content and tested as electrodes for magnesium-ion batteries. The synthesized ceramics are characterized by thermogravimetric-mass spectroscopy, Fourier-transform infrared spectroscopy, X-ray diffraction (XRD), Raman spectroscopy, N2 sorption analysis, scanning electron microscope, energy-dispersive X-ray, and elemental analysis. Galvanostatic cycling tests, rate performance tests, electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV) tests, and ex situ XRD measurements are conducted. Results of battery performance tests present a high capacity of 198.2 mAh g-1 after the first discharging and a reversible capacity of 144.5 mAh g-1 after 100 cycles at 500 mA g-1. Excellent rate performance efficiency of 85.2% is achieved. Battery performances in this research are influenced by surface area, and tin contentof the SiOC/Sn nanobeads. EIS, CV tests, and ex situ XRD measurements reveal that higher surface area contributes to higher capacity by providing more accessible Mg2+ ion storage sites and higher rate capability by improving the diffusion process. Higher Sn content increases battery capacity through reversible Mg-Mg2Sn-Mg alloying/dealloying process and improves the rate performances by increasing electrical conductivity. Besides, SiOC advances cycling stability by preventing electrode collapse and enhances the capacity due to higher surface capacitive effects. SiOC nanobeads containing Sn nanoparticles are synthesized and tested as anode for magnesium-ion batteries. The anodes show high performance with reversible capacity of 144.5 mAh g-1 after 100 cycles at 500 mA g-1 and excellent rate performance efficiency of 85.2% from 50 to 500 mA g-1.imageArticle Citation - WoS: 8Citation - Scopus: 8Design and Performance Comparison of Polymer-Derived Ceramic Ambigels and Aerogels(American Chemical Society, 2023) Soraru, Gian Domenico; İçin, Öykü; Semerci, Tuğçe; Ahmetoğlu, Çekdar VakıfThis work reports the synthesis and characterization of preceramic-and polymer-derived SiOC aerogels obtained from a commercial siloxane resin. The preceramic aerogels were obtained by ambient pressure drying (ambigels) and CO2 supercritical drying. Despite different drying processes, the final ceramic ambi/aerogels have very similar microstructural features in density, porosity, pore size, and specific surface area. Both materials have shown promising results for oil sorption and water cleaning. Supercritically dried-SiOC aerogel had low thermal conductivity with 0.046 W.m(-1).K-1 at RT and 0.073 W.m(-1).K-1 at 500 degrees C. These results suggest that substituting the rather complicated and expensive CO2-SC drying with the more friendly and cheap ambient pressure drying can be done without having to accept significant microstructural/property degradation.Review Citation - WoS: 41Citation - Scopus: 42Review on the Parameters of Recycling Ndfeb Magnets Via a Hydrogenation Process(American Chemical Society, 2023) Habibzadeh, Alireza; Küçüker, Mehmet Ali; Gökelma, MertolRegarding the restrictions recently imposed by China on the export of rare-earth elements (REEs), the world may face a serious challenge in supplying some REEs such as neodymium and dysprosium soon. Recycling secondary sources is strongly recommended to mitigate the supply risk of REEs. Hydrogen processing of magnetic scrap (HPMS) as one of the best approaches for magnet-to-magnet recycling is thoroughly reviewed in this study in terms of parameters and properties. The processes of hydrogen decrepitation (HD) and hydrogenation-disproportio-nation-desorption-recombination (HDDR) are two common methods for HPMS. Employing a hydrogenation process can shorten the production route of new magnets from the discarded magnets compared to other recycling routes such as the hydrometallurgical route. However, determining the optimal pressure and temperature for the process is challenging due to the sensitivity to the initial chemical composition and the interaction of temperature and pressure. Pressure, temperature, initial chemical composition, gas flow rate, particle size distribution, grain size, and oxygen content are the effective parameters for the final magnetic properties. All these influencing parameters are discussed in detail in this review. The recovery rate of magnetic properties has been the concern of most research in this field and can be achieved up to 90% by employing a low hydrogenation temperature and pressure and using additives such as REE hydrides after hydrogenation and before sintering.Article Citation - WoS: 22Citation - Scopus: 25Effect of Solution Heat Treatment on the Microstructure and Crystallographic Texture of In939 Fabricated by Powder Bed Fusion-Laser Beam(Elsevier, 2023) Doğu, Merve Nur; Özer, Seren; Yalçın, Mustafa Alp; Davut, Kemal; Bilgin, Guney Mert; Obeidi, Muhannad Ahmed; Brodin, Hakan; Gu, Hengfeng; Brabazon, DermotThe effect of various solution heat treatment temperatures (i.e., 1120, 1160, 1200 and 1240 & DEG;C) on the microstructure, grain morphology and crystallographic texture of IN939 fabricated by powder bed fusion-laser beam (PBF-LB) was investigated. Microstructural analyses showed that the high-temperature gradient and rapid solidification of the PBF-LB processing caused different resulting microstructures compared to conventionally pro-duced counterparts. The melt pool morphologies and laser scanning paths were examined in the as-fabricated samples in the XZ-and XY-planes, respectively. After the application of solution heat treatment at 1120 & DEG;C, the as-fabricated PBF-LB initial microstructure was still apparent. For solution heat treatments of 1200 & DEG;C and above, the melt pool and scanning path morphologies disappeared and converted into a mixture of columnar grains in the XZ-plane and equiaxed grains in the XY-plane. On the other hand, large equiaxed grains were observed when the samples were solutionized at 1240 & DEG;C. Additionally, g' phase precipitated within the matrix after all solution heat treatment conditions, which led to increase in the microhardness values. According to electron backscatter diffraction (EBSD) analyses, both as-fabricated and solution heat-treated samples had intense texture with {001} plane normal parallel to the building direction. The first recrystallized grains began to appear when the samples were subjected to the solution heat treatment at 1160 & DEG;C and the fraction of the recrystallized grains increased with increasing temperature, as supported by kernel average misorientation (KAM) and grain spread orientation (GOS) analyses.& COPY; 2023 The Author(s). Published by Elsevier B.V. This is an open access article under the CC BY license (http://creativecommons.org/licenses/by/4.0/).Article Citation - WoS: 18Citation - Scopus: 22Biomimetic Dentin Repair: Amelogenin-Derived Peptide Guides Occlusion and Peritubular Mineralization of Human Teeth(American Chemical Society, 2023) Fong, Hanson; Hamann, John; Hall, Eric; Yücesoy, Deniz T.; Doğan, Sami; Sarıkaya, MehmetExposure of dentin tubules due to loss of protective enamel (crown) and cementum (root) tissues as a result of erosion, mechanical wear, gingival recession, etc. has been the leading causes of dentin hypersensitivity. Despite being a widespread ailment, no permanent solution exists to address this oral condition. Current treatments are designed to alleviate the pain by either using desensitizers or blocking dentin tubules by deposition of minerals or solid precipitates, which often have short-lived effects. Reproducing an integrated mineral layer that occludes exposed dentin with concomitant peritubular mineralization is essential to reestablish the structural and mechanical integrity of the tooth with long-term durability. Here, we describe a biomimetic treatment that promotes dentin repair using a mineralization directing peptide, sADP5, derived from amelogenin. The occlusion was achieved through a layer-by-layer peptide-guided remineralization process that forms an infiltrating mineral layer on dentin. The structure, composition, and nanomechanical properties of the remineralized dentin were analyzed by cross-sectional scanning electron microscopy imaging, energy dispersive X-ray spectroscopy, and nanomechanical testing. The elemental analysis provided calcium and phosphate compositions that are similar to those in hydroxyapatite. The measured average hardness and reduced elastic modulus values for the mineral layer were significantly higher than those of the demineralized and sound human dentin. The structural integration of the new mineral and underlying dentin was confirmed by thermal aging demonstrating no physical separation. These results suggest that a structurally robust and mechanically durable interface is formed between the interpenetrating mineral layer and underlying dentin that can withstand long-term mechanical and thermal stresses naturally experienced in the oral environment. The peptide-guided remineralization procedure described herein could provide a foundation for the development of highly effective oral care products leading to novel biomimetic treatments for a wide range of demineralization-related ailments and, in particular, offers a potent long-term solution for dentin hypersensitivity.Article Citation - WoS: 14Citation - Scopus: 13An Experimental Study on the Ballistic Performance of Ultra-High Hardness Armor Steel (armox 600t) Against 7.62 Mm × 51 M61 Ap Projectile in the Multi-Hit Condition(Elsevier, 2023) Göde, Engin; Teoman, Atanur; Çetin, Barış; Tonbul, Kürşat; Davut, Kemal; Kuşhan, Melih CemalIn this study, Armox 600T armor steel was ballistically tested against 7.62 mm × 51 M61 AP projectile. The experimental design was constructed on the basis of the worst-case scenario which is the highest possible impact velocity in the multi-hit condition. The ballistic tests revealed that Armox 600T could defeat the worst-case scenario with a thickness of 12 mm. Furthermore, the damaged and undamaged regions were inspected microstructurally in a detail manner aiming to observe the possible fractographic modes of the studied material. Finally, high resolution optical scanning efforts were also added to the experimental work whose results uncovers the possible improvement areas regarding the quantification of the results of ballistic testing.Review Citation - WoS: 44Citation - Scopus: 48Review on Polymeric, Inorganic, and Composite Materials for Air Filters: From Processing To Properties(John Wiley and Sons Inc, 2021) Henning,L.M.; Abdullayev,A.; Vakifahmetoglu,C.; Simon,U.; Bensalah,H.; Gurlo,A.; Bekheet,M.F.Particulate and gaseous air pollutants pose a threat to human health and contribute to climate change. By today, air filters, stationary and portable, are markedly improved and can often provide innocuous air pollution levels. After introducing the classification and standards on air filters, the influence of the processing route and its parameters on the resulting air filter properties and consequently its performance are discussed. Numerous tools are presented to adjust structural properties such as fiber or pore diameter, specific surface area, surface charge, hydrophilicity, or photocatalytic activity to achieve the desired performance in terms of high filtration efficiencies, sufficient mechanical stability, regeneration eligibility, antimicrobial and optical properties. In particular, inorganic and composite materials as well as nonfibrous structures are covered, which are currently holding an outsider position in an air filter community dominated by polymeric materials and fibrous structures. © 2021 The Authors. Advanced Energy and Sustainability Research published by Wiley-VCH GmbH.Article Citation - WoS: 18Citation - Scopus: 22Effect of Fomes Fomentarius Cultivation Conditions on Its Adsorption Performance for Anionic and Cationic Dyes(American Chemical Society, 2022) Henning, Laura M.; Simon, Ulla; Abdullayev, Amanmyrat; Schmidt, Bertram; Pohl, Carsten; Nunez Guitar, Tamara; Ahmetoğlu, Çekdar Vakıf; Meyer, Vera; Bekheet, Maged F.; Gurlo, AleksanderLab-cultivated mycelia of Fomes fomentarius (FF), grown on a solid lignocellulose medium (FF-SM) and a liquid glucose medium (FF-LM), and naturally grown fruiting bodies (FF-FB) were studied as biosorbents for the removal of organic dyes methylene blue and Congo red (CR). Both the chemical and microstructural differences were revealed using X-ray photoelectron spectroscopy, Fourier-transform infrared spectroscopy, zeta potential analysis, and scanning electron microscopy, illuminating the superiority of FF-LM and FF-SM over FF-FB in dye adsorption. The adsorption process of CR on FF-LM and FF-SM is best described by the Redlich-Peterson model with β constants close to 1, that is, approaching the monolayer Langmuir model, which reach maximum adsorption capacities of 48.8 and 13.4 mg g-1, respectively, in neutral solutions. Adsorption kinetics follow the pseudo-second-order model where chemisorption is the rate-controlling step. While the desorption efficiencies were low, adsorption performances were preserved and even enhanced under simulated dye effluent conditions. The results suggest that F. fomentarius can be considered an attractive biosorbent in industrial wastewater treatment and that its cultivation conditions can be specifically tailored to tune its cell wall composition and adsorption performance.Article Citation - WoS: 17Citation - Scopus: 19Strong Coupling of Carbon Quantum Dots in Liquid Crystals(American Chemical Society, 2022) Sarısözen, Sema; Polat, Nahit; Mert Balcı, Fadime; Güvenç, Çetin Meriç; Kocabaş, Çoşkun; Yağlıoğlu, Halime Gül; Balcı, SinanCarbon quantum dots (CDs) have recently received a tremendous amount of interest owing to their attractive optical properties. However, CDs have broad absorption and emission spectra limiting their application ranges. We herein, for the first time, show synthesis of water-soluble red emissive CDs with a very narrow line width (∼75 meV) spectral absorbance and hence demonstrate strong coupling of CDs and plasmon polaritons in liquid crystalline mesophases. The excited state dynamics of CDs has been studied by ultrafast transient absorption spectroscopy, and CDs display very stable and strong photoluminescence emission with a quantum yield of 35.4% and a lifetime of ∼2 ns. More importantly, we compare J-aggregate dyes with CDs in terms of their absorption line width, photostability, and ability to do strong coupling, and we conclude that highly fluorescent CDs have a bright future in the mixed light-matter states for emerging applications in future quantum technologies.