Materials Science and Engineering / Malzeme Bilimi ve Mühendisliği

Permanent URI for this collectionhttps://hdl.handle.net/11147/4719

Browse

Filters

2021 - 20233

Settings

Author: search.filters.author.Demir, Mustafa M.Publisher: search.filters.publisher.Elsevier

Search Results

Now showing 1 - 3 of 3
  • Article
    Citation - WoS: 20
    Citation - Scopus: 22
    Fabrication and Properties of Novel Porous Ceramic Membrane Supports From the (sig) Diatomite and Alumina Mixtures
    (Elsevier, 2022) Aouadja, Faycal; Bouzerara, Ferhat; Güvenç, Çetin Meriç; Demir, Mustafa M.
    In this paper, the manufacturing of macro-porous tubular ceramic supports for membranes is described. The novel supports are fabricated from natural diatomite and alumina raw materials using the extrusion method. The structure was analyzed by X-ray diffraction (XRD) and mercury porosimetry techniques; the presence of possible defects was investigated by scanning electron microscopy (SEM). The permeability has been measured from water flux in standard experiments. Experimental results show that the open porosity, the average pore size (APS), the pore size distribution, the strength, and the permeability of sintered supports, have been found to depend, mainly on the concentration of alumina (Al2O3) additive. Supports prepared with the addition of 10 wt.% of alumina and sintered at 1200 degrees C, can be considered as the most optimized; they have a porosity ratio of about 46%, an APS is around 7.7 mu m, a flexural strength value of about 28 MPa, and water permeability of around 15 m(3)h(-1) m(-2) bar(-1). Such materials could be of great interest in the supports fabrication for membrane application, for instance, water filtration. (C) 2021 SECV. Published by Elsevier Espana, S.L.U.
  • Article
    Citation - WoS: 11
    Citation - Scopus: 11
    Enhanced Electrocaloric Effect of P(vdf-Trfe) Nanocomposites With Ca and Sn Co-Doped Batio3 Particles
    (Elsevier, 2023) Tokkan, Melike; Demir, Mustafa M.; Adem, Umut
    We report on the enhancemenent of electrocaloric effect in solution cast polymer nanocomposites based on Poly (vinylidene fluoride-co-trifluoroethylene) [P(VDF-TrFE) 55-45] with Ca and Sn co-substituted BaTiO3 ceramic fillers (Ba0.94Ca0.06Ti0.925Sn0.075O3, BCST). Saturated hysteresis loops and normal ferroelectric behaviour of the copolymer-based nanocomposites-as opposed to the relaxor ferroelectric nature of the terpolymer-based ones-allow the utilization of the indirect method to estimate the electrocaloric properties. Both the dielectric constant and electrocaloric temperature change (AT) increases as the particle content increases. Maximum adiabatic temperature change was obtained as 6.96 K under 900 kV/cm for the 10 vol % BCST containing polymer composite around the Curie temperature of the copolymer (70 degrees C). This relatively large electrocaloric strength is slightly lower than those obtained for terpolymer-based nanocomposites.
  • Article
    Citation - WoS: 22
    Citation - Scopus: 25
    Cryopreservation of a Cell-Based Biosensor Chip Modified With Elastic Polymer Fibers Enabling Ready-To On-Site Applications
    (Elsevier, 2021) Özsoylu, Dua; Isık, Tuğba; Demir, Mustafa M.; Schoning, Michael J.; Wagner, Torsten
    An efficient preservation of a cell-based biosensor chip to achieve a ready-to-use on-site system is still very challenging as the chip contains a living component such as adherent mammalian cells. Herein, we propose a strategy called on-sensor cryopreservation (OSC), which enables the adherent cells to be preserved by freezing (-80 degrees C) on a biosensor surface, such as the light-addressable potentiometric sensor (LAPS). Adherent cells on rigid surfaces are prone to cryo-injury; thus, the surface was modified to enhance the cell recovery for OSC. It relies on i) the integration of elastic electrospun fibers composed of polyethylene vinyl acetate (PEVA), which has a high thermal expansion coefficient and low glass-transition temperature, and ii) the treatment with O-2 plasma. The modified sensor is integrated into a microfluidic chip system not only to decrease the thermal mass, which is critical for fast thawing, but also to provide a precisely controlled micro-environment. This novel cryo-chip system is effective for keeping cells viable during OSC. As a proof-of-concept for the applicability of a ready-to-use format, the extracellular acidification of cancer cells (CHO-K1) was evaluated by differential LAPS measurements after thawing. Results show, for the first time, that the OSC strategy using the cryo-chip allows label-free and quantitative measurements directly after thawing, which eliminates additional post-thaw culturing steps. The freezing of the chips containing cells at the manufacturing stage and sending them via a cold-chain transport could open up a new possibility for a ready-to-use on-site system.