Materials Science and Engineering / Malzeme Bilimi ve Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4719
Browse
18 results
Search Results
Article Citation - WoS: 3Citation - Scopus: 3Green Fabrication of Lanthanide-Doped Hydroxide-Based Phosphors: Y(oh)(3):eu3+ Nanoparticles for White Light Generation(Beilstein-Institut Zur Forderung der Chemischen Wissenschaften, 2019) Güner, Tuğrul; Kuş, Anılcan; Özcan, Mehmet; Genç, Aziz; Şahin, Hasan; Demir, Mustafa MuammerPhosphors can serve as color conversion layers to generate white light with varying optical features, including color rendering index (CRI), high correlated color temperature (CCT), and luminous efficacy. However, they are typically produced under harsh synthesis conditions such as high temperature, high pressure, and/or by employing a large amount of solvent. In this work, a facile, water-based, rapid method has been proposed to fabricate lanthanide-doped hydroxide-based phosphors. In this sense, sub-micrometer-sized Y(OH)(3):Eu3+ particles (as red phosphor) were synthesized in water at ambient conditions in <= 60 min reaction time. The doping ratio was controlled from 2.5-20 mol %. Additionally, first principle calculations were performed on Y(OH)(3):Eu3+ to understand the preferable doping scenario and its optoelectronic properties. As an application, these fabricated red phosphors were integrated into a PDMS/YAG:Ce3+ composite and used to generate white light. The resulting white light showed a remarkable improvement (approximate to 24%) in terms of luminous efficiency, a slight reduction of CCT (from 3900 to 3600 K), and an unchanged CRI (approximate to 60) as the amount of Y(OH)(3):Eu3+ was increased.Article Citation - WoS: 3Citation - Scopus: 4Experimental and First-Principles Investigation of Cr-Driven Color Change in Cesium Lead Halide Perovskites(American Institute of Physics, 2019) Özen, Sercan; Güner, Tuğrul; Topçu, Gökhan; Özcan, Mehmet; Demir, Mustafa Muammer; Şahin, HasanHerein, we report room temperature Cr-doping for all-inorganic perovskites that have attracted great attention in recent years due to their extraordinary optical properties, low cost, and ease of synthesis. Incorporation of Cr 3 + ions into the perovskite crystal lattices is achieved by following a facile route involving an antisolvent recrystallization method at room temperature. It is shown that both Cr-doping and formation of crystals in the CsPbBr x Cl 3 - x phase are provided by increasing the concentration of the CrCl 3 solution. It is also observed that the doping procedure leads to the emergence of three types of distinctive peaks in the PL spectrum originating from CsPbBr x Cl 3 - x domains (476-427nm), Cr-strained host lattices (515nm), and midgap states formed by Cr dopants (675-775nm). It is also found that the Cr-doped perovskites emitting a dark violaceous color change their color to white with a high color rendering index (88) in 30-day time intervals. Easy-tunable optical properties of all-inorganic Cs perovskites indicate their great potential for future optoelectronic device applications.Article Citation - WoS: 50Citation - Scopus: 58Chemically Modified Optical Fibers in Advanced Technology: an Overview(Elsevier, 2019) Shukla, S. K.; Kushwaha, Chandra Shekhar; Güner, Tuğrul; Demir, Mustafa MuammerIn recent years, chemically modified optical fibers have widely used for development of several advanced chemical and biosensors, biomedical technology and environmental monitoring. The chemically modified optical fiber bears several valuable properties like energy loss, catalytic behaviour, refractive index, and mechanical strength to advance the optical fiber technology. In this article, we reviewed the chemically-modified optical fiber and their applications in different optical fiber-based technologies. The basics of optical fiber and their modification are discussed along with the adopted methodologies. The advancements in different optical fiber based technologies viz sensing, imaging, tomography, magnetic resonance imaging, photodynamic therapy, optogenics, surgery and environmental monitoring are discussed in the light of the contribution of chemically modified optical fibers. In conclusion, success and challenges for the use of chemically modified-optical fiber are presented on the basis of existing literature.Article Citation - WoS: 25Citation - Scopus: 28Colorimetric and Plasmonic Pressure Sensors Based on Polyacrylamide/Au Nanoparticles(Elsevier, 2019) Topçu, Gökhan; Güner, Tuğrul; İnci, Ezgi; Demir, Mustafa MuammerColorimetric stimuli-responsive nanomaterials have emerged as an eminent tool for sensor applications. Among this class of sensing elements, gold nanoparticle-based (Au NP) nanostructures are promising materials due to their plasmonic features. In this study, free-standing flexible polymeric films having intense optical response upon application of mechanical pressure were fabricated based on polyacrylamide (PAAm) and Au NPs. Pressure may cause plasmonic shift most probably due to the disassembly of the clusters from blue to reddish individual particles depending on the extent of pressure. Temperature, time, and extent of pressure were examined in terms of spectral change of Au particles. The sensor films depict working range up to 160 MPa, which shows minor change at elevated temperatures probably due to the stress induced crystallization of PAAm. For practical applications, a simple red-green-blue (RGB) space-based algorithm was presented for smartphone-assisted detection of applied pressure. Moreover, the PAAm/Au composite structure shows self-healing without any additive under ambient conditions even after divided into pieces. (C) 2019 Elsevier B.V. All rights reserved.Article Citation - WoS: 89Citation - Scopus: 85Cspbbr3 Perovskites: Theoretical and Experimental Investigation on Water-Assisted Transition From Nanowire Formation To Degradation(American Physical Society, 2018) Akbalı, Barış; Topçu, Gökhan; Güner, Tuğrul; Özcan, Mehmet; Demir, Mustafa Muammer; Şahin, HasanRecent advances in colloidal synthesis methods have led to an increased research focus on halide perovskites. Due to the highly ionic crystal structure of perovskite materials, a stability issue pops up, especially against polar solvents such as water. In this study, we investigate water-driven structural evolution of CsPbBr3 by performing experiments and state-of-the-art first-principles calculations. It is seen that while an optical image shows the gradual degradation of the yellowish CsPbBr3 structure under daylight, UV illumination reveals that the degradation of crystals takes place in two steps: transition from a blue-emitting to green-emitting structure and and then a transition from a green-emitting phase to complete degradation. We found that as-synthesized CsPbBr3 nanowires (NWs) emit blue light under a 254 nm UV source. Before the degradation, first, CsPbBr3 NWs undergo a water-driven structural transition to form large bundles. It is also seen that formation of such bundles provides longer-term environmental stability. In addition theoretical calculations revealed the strength of the interaction of water molecules with ligands and surfaces of CsPbBr3 and provide an atomistic-level explanation to a transition from ligand-covered NWs to bundle formation. Further interaction of green-light-emitting bundles with water causes complete degradation of CsPbBr3 and the photoluminescence signal is entirely quenched. Moreover, Raman and x-ray-diffraction measurements revealed that completely degraded regions are decomposed to PbBr2 and CsBr precursors. We believe that the findings of this study may provide further insight into the degradation mechanism of CsPbBr3 perovskite by water.Article Citation - WoS: 30Citation - Scopus: 32Perylene-Embedded Electrospun Ps Fibers for White Light Generation(Elsevier Ltd., 2019) Güner, Tuğrul; Aksoy, Erkan; Demir, Mustafa Muammer; Varlıklı, CananPerylene dyes have been employed in the fabrication of white light due to their superior photophysical properties and relatively easy synthetic methods. However, their molecular aggregation in solid state is one of the main handicaps since it causes deviation in their optical properties and quenches photoluminescence quantum yields (Phi(f)). Investigation of the photophysical properties of a green (PTE), a yellow (PDI) and a new red (DiPhAPDI) emitting perylene derivative in solution, drop-casted films, polystyrene (PS) fibers and PS fibers embedded in poly (dimethyl siloxane) (PDMS) showed that PS:dye fibers prevent aggregation to some extend and allows high Of of dyes. The Of values of PTE, PDI and DiPhAPDI were all higher than 93.0% in solution and 84.8%, 94.3% and 73.6%, respectively in PS:dye fibers. Embedding the fibers in PDMS improved the photostabilities of the dyes two folds compared to their solution phases. The prepared dye containing fibers were combined together into a single PDMS film and utilized as a frequency conversion layer on a blue LED. Fabricated samples were found to show high color rendering index (>= 90), adjustable CCT (7500 K-5000 K), and power efficiency values exceeding 2001m/W depending on the used fiber amount in mass.Article Citation - WoS: 18Citation - Scopus: 46Phosphor-Based White Led by Various Glassy Particles:control Over Luminous Efficiency(The Optical Society, 2019) Yüce, Hürriyet; Güner, Tuğrul; Balcı, Sinan; Demir, Mustafa MuammerGenerating white light through a mainstream remote phosphor design suffers from phosphor conversion efficiency loss due to a backscattering of light. Such a loss also reduces luminous efficiency of the resulting white light. To overcome this issue, various glassy scatterers with different morphologies such as glass bubbles, glass beads, and nanosized silica particles were employed as scatterers, together with a fixed amount of yellow phosphor (YAG:Ce3+) and a poly(dimethylsiloxane) (PDMS) matrix. In addition, the simulation of the system validates the rigorous multiple scattering of the incoming light most probably due to refractive index mismatch between the glass bubbles and surrounding PDMS matrix along with the internal reflections. (C) 2019 Optical Society of AmericaArticle Citation - WoS: 5Citation - Scopus: 5Enhancement of the Spontaneous Emission Rate of Perovskite Nanowires Coupled Into Cylindrical Hollow Nanocavities Formed on the Surface of Polystyrene Microfibers(American Chemical Society, 2019) Gökbulut, Belkis; İnanç, Arda; Topçu, Gökhan; Güner, Tuğrul; Demir, Mustafa Muammer; İnci, M. NaciFluorescent CsPbBr3 nanowires are uniformly integrated into a porous polystyrene matrix in the form of microfibers to investigate the changes in their spontaneous emission rate. Cylindrical hollow nanocavities, ranging from 75 to 160 nm in diameter, are grown on the surface of the polymer microfibers during the fabrication process, which allow coupling light that is emitted from the excited CsPbBr3 nanowires. Time-resolved experiments elucidate that the spontaneous emission rate of the perovskite nanowires is observed to increase by a factor of 4.9, upon coupling of the excited optical modes into the nanocavities, which is demonstrated to be in good agreement with our theoretical calculations.Article Citation - WoS: 18Citation - Scopus: 14Optimization and Performance of Nitrogen-Doped Carbon Dots as a Color Conversion Layer for White-Led Applications(Beilstein-Institut Zur Forderung der Chemischen Wissenschaften, 2019) Güner, Tuğrul; Yüce, Hürriyet; Taşçıoğlu, Didem; Şimşek, Eren; Savacı, Umut; Genç, Aziz; Demir, Mustafa MuammerIn this study, green-emitting nitrogen-doped carbon dots (N-CDots) were synthesized and incorporated into drop-cast composite films for use as color conversion layers in a white-LED configuration to generate white light. In order to resolve the red deficiency of this configuration, a commercial red phosphor was integrated into the system. Moreover, the N-CDots were also processed into polymer/N-CDot composite fibers, for which we determined the amount of N-CDots that yielded adequate white-light properties. Finally, we showed that white light with excellent properties could be generated by employing both of the fabricated N-CDot composites either as drop-cast films or composite fibers. Hence, N-CDots provide a promising alternative to inorganic phosphors that are commonly employed in white-LED configurations.Article Citation - WoS: 84Citation - Scopus: 85A Review on Halide Perovskites as Color Conversion Layers in White Light Emitting Diode Applications(John Wiley and Sons Inc., 2018) Güner, Tuğrul; Demir, Mustafa MuammerIn the last decade, halide perovskites have attracted great interest due to many reasons, including their low cost, solution-processability, superior PL properties, broad range of color tunability, color purity, and defect tolerance, among others. They are in increasing demand for a wide range of applications, such as solar cells, light emitting diodes (LEDs), white LEDs (WLED), and lasers. Yellow phosphors have been heavily employed in solid-state lighting, since its illumination by blue yields white light with various optical features, such as high/low CRI, CCT, and luminous efficiency. However, phosphors as pigments are seldom found and are costly material. In this sense, halide perovskites may offer a promising alternative to phosphors for future solid-state lighting. In this study, the synthesis and optical properties of halide perovskites, as well as their application in WLED as a conversion layer are investigated.