Materials Science and Engineering / Malzeme Bilimi ve Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4719
Browse
15 results
Search Results
Article Citation - WoS: 3Citation - Scopus: 4A Facile Method for Boosting the Graphitic Carbon Nitride's Photocatalytic Activity Based on 0d/2d S-Scheme Heterojunction Nanocomposite Architecture(Elsevier, 2024) Kahraman, Zeynep; Kartal, Uğur; Gent, Aziz; Alp, EmreGraphitic carbon nitride (g-C 3 N 4 ) has received significant interest as a metal -free photocatalyst. The S -scheme photocatalytic system has great potential to improve the charge separation in semiconductor photocatalysts. In this study, we have fabricated non-toxic and low-cost photocatalytic nanocomposites of 0D/2D S -scheme heterojunction composed of iron oxide and graphitic carbon nitride by a facile method. The developed facile method provides a sustainable way with a high atom economy to further enhance the photocatalytic performance of exfoliated g-C 3 N 4 . The 0D -iron oxide/2D-C 3 N 4 exhibited nearly 10 times better than bulk g-C 3 N 4 and almost 60 % better than exfoliated g-C 3 N 4 under simulated solar light irradiation. The experimental results demonstrated that the effective charge -carrier mechanism led to an improved generation of reactive oxygen species (ROSs), resulting in an impressive photocatalytic performance. A serial photocatalytic test was also conducted to understand photocatalytic reaction mechanisms with various scavengers.Article Citation - WoS: 8Citation - Scopus: 10Impact of Simulated Inflammation and Food Breakdown on the Synergistic Interaction Between Corrosion and Wear on Titanium(Elsevier, 2024) Lima, A.R.; Pinto, A.M.P.; Toptan, F.; Alves, A.C.This paper investigates the impact of lactic acid and phosphoric acid additives in artificial saliva (AS), simulating inflammation and food breakdown, on the electrochemical and tribo-electrochemical behavior of titanium. The results showed that, unlike lactic acid, phosphoric acid significantly reduced corrosion resistance, mainly due to local damage and heterogeneities on the passive film. Non-additivated AS caused greater wear volume loss, with mechanical wear identified as the main mechanism. However, when additives were present, a synergistic interplay between corrosion and wear was observed. The study concludes that prolonged exposure to food breakdown could accelerate material degradation in titanium. © 2024 Elsevier LtdArticle Citation - WoS: 9Citation - Scopus: 9Cold Sintering Assisted Two-Step Sintering of Potassium Sodium Niobate (knn) Ceramics(Elsevier, 2023) Karacasulu, Levent; Ahmetoğlu, Çekdar VakıfPotassium sodium niobate (KNN) ceramics were densified using a multiple-stage sintering process in which initially applied cold sintering process (CSP) was followed by the solid-state sintering between 1100 and 1120 °C. Comparative assessments demonstrated that multi-step sintered samples yielded better properties than conventionally sintering ones. The highest relative density (94.7%) and the best electrical properties were obtained from the sample subjected to cold sintering at 120 °C/1 h using 5 wt% deionized water subsequently heat-treated at 1120 °C/2 h, resulting in a monolithic KNN ceramic having a piezoelectric coefficient of 120 pC/N. © 2023 Elsevier B.V.Article Citation - WoS: 5Citation - Scopus: 6Formation of Monolithic Srtio3-Tio2 Ceramic Heterostructures by Reactive Hydrothermal Sintering(Elsevier, 2023) Karacasulu, Levent; Kartal, Uğur; İçin, Öykü; Bortolotti, Mauro; Biesuz, Mattia; Ahmetoğlu, Çekdar VakıfIn a one-pot approach, monolithic SrTiO3-TiO2 ceramic heterostructures were obtained using the reactive hydrothermal liquid phase densification (rHLPD). Structural, morphological, and photocatalytic properties of the obtained ceramics were analyzed. The relative density of the formed components reached about 80% with reaction time, temperature, and NaOH concentration variation. It was observed via Rietveld refinement that there was no XRD detectable phase other than TiO2 and SrTiO3 in the final structure. The monolithic SrTiO3-TiO2 ceramics obtained by hydrothermal reaction at 120 °C for 24 h in 1 M NaOH concentration showed a dielectric constant being around 500, and the dielectric loss was below 0.25 at frequencies higher than 10 kHz. The SrTiO3-TiO2 heterostructured monoliths having only 20 vol% total porosity and low specific surface area, demonstrated ∼60% efficiency (in 5 h) in degrading Methylene Blue photo-catalytically. © 2023 Elsevier LtdArticle Citation - WoS: 14Citation - Scopus: 20Influence of Al2o3 Reinforcements and Ti-Al Intermetallics on Corrosion and Tribocorrosion Behavior of Titanium(Elsevier, 2023) Sousa, Luis; Antunes, Rui D. M.; Fernandes, Joao C. S.; Alves, Alexandra Cruz; Toptan, FatihTi-Al2O3 composites have demonstrated favorable characteristics for use in load-bearing biomedical implant applications; however, the influence of Al2O3 reinforcement particles and Ti-Al intermetallics on the electrochemical and tribo-electrochemical responses of Ti are not well-understood. This study explored the corrosion and tribocorrosion characteristics of powder metallurgy-manufactured Ti-Al2O3 composites in a simple physiological saline solution at body temperature. Electrochemical analysis was performed by electrochemical impedance spectroscopy (EIS), and potentiodynamic polarization and tribo-electrochemical mechanisms were explored under open circuit potential (OCP) against a 10 mm diameter alumina ball in a ball-on-plate tribometer with reciprocating configuration. Results revealed that the corrosion behavior of Ti was adversely affected by the development of a heterogeneous oxide film on the Ti matrix and the Ti-Al intermetallic phases formed by the interaction of Ti and Al2O3 particles. However, there was a drastic improvement in tribocorrosion behavior, evidenced by decreased corrosion tendency under sliding and a marked reduction in wear volume, primarily as a result of the decreased wear damage resulting from the load-bearing reinforcements.Article Citation - WoS: 8Citation - Scopus: 8Crystallization and Additional Oxide Interlayers Improve the Tribocorrosion Resistance of Tio2 Nanotubular Surfaces Formed on Ti6al4v(Elsevier, 2023) Çaha, İhsan; Türü, İrem Cemre; Erdoğan, Ece; Pinto, Ana Maria Pires; Cansever, Nurhan; Deepak, Francis Leonard; Toptan, Fatih; Alves, Alexandra C.TiO2-based nanotubular surfaces have promising properties for various industrial applications, such as solar cells, fuel cells, photocatalysis, energy storage, gas sensors, and biomedical applications. However, they have very limited use in real applications, and one of the major limiting factors is the weak adhesion of nanotubular surfaces to the substrate. In this study, nanotubular surfaces are formed on Ti6Al4V alloy by anodic treatment followed by a heat treatment at 500 °C for 3 h under an open atmosphere. Microstructural investigations revealed self-organized nanotubes grown on both ? and ? phases. High-resolution TEM/STEM analysis showed crystallization of the nanotubular layer and formation of additional oxide interlayers resulting in a drastic improvement in tribocorrosion resistance. These findings indicated that a simple heat treatment can significantly alter the properties of nanotubular layers and can widen their usage mainly for load-bearing implant applications in corrosive environments. © 2023 Elsevier B.V.Article Citation - WoS: 29Citation - Scopus: 31Effect of Heat Input on Haz Softening in Fiber Laser Welding of 22mnb5 Steel(Elsevier, 2023) Tuncel, Oğuz; Aydın, Hakan; Davut, KemalThis study investigates the effects of heat input on the heat-affected zone (HAZ) softening in fiber laser welding of quenched 1.1 mm thick 22MnB5 steel. Laser power (1500-2500 W) and welding speed (40-120 mm/s) parameters are considered as the input process variables. Depending on the input parameters, the applied heat input varied between 12.5 and 62.5 J/mm. The results indicate that a minimum heat input of 50 J/mm is required for full weld penetration. Microhardness findings revealed that the drop in hardness in the HAZ region relative to the base material (BM) reached 39% due to grain coarsening caused by an increase in heat input under the welding conditions. Grain coarsening (prior austenite grains) is also detected in SEM analysis. In addition, grain coarsening at high heat input was also determined quantitatively in EBSD analyses. The proportion of 8.91 mu m grain size in the sample with high heat input is 4.2%, while it is 1.2% in the sample with low heat input. When the heat input increased from 12.5 to 62.5 J/mm, the width of the softened zone with the lowest hardnesses in the HAZ grew from 0.2 mm to 2.2 mm.Article Citation - WoS: 24Citation - Scopus: 27Atomic–scale Investigations of Passive Film Formation on Ti-Nb Alloys(Elsevier, 2023) Çaha, İhsan; Alves, Alexandra C.; Chirico, Caterina; Maria Pinto, Ana; Tsipas, Sophia; Gordo, Elena; Bondarchuk, Oleksandr; Leonard Deepak, Francis; Toptan, FatihThis study extensively investigates the passive film formation mechanisms on Ti-xNb alloys by using several electrochemical techniques, including electrochemical impedance spectroscopy (EIS) before and after potentiostatic polarization at the passive zone, and Mott-Schottky (MS) measurements in 9 g/l NaCl electrolyte at 37 °C, together with X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM) analysis. Overall, the Ti40Nb presented lower corrosion resistance due to a thinner passive film as compared to commercial pure Ti (grade 2) and Ti12Nb. The passive film formed on Ti12Nb and Ti40Nb alloys at a steady-state condition (+0.5 VAg/AgCl for 60 min) is composed of amorphous phases of TiO, Ti2O3, TiO2, Nb2O5 and crystalline phases of TiO2 (anatase) and Nb2O5. © 2022 Elsevier B.V.Article Citation - WoS: 11Citation - Scopus: 11Enhanced Electrocaloric Effect of P(vdf-Trfe) Nanocomposites With Ca and Sn Co-Doped Batio3 Particles(Elsevier, 2023) Tokkan, Melike; Demir, Mustafa M.; Adem, UmutWe report on the enhancemenent of electrocaloric effect in solution cast polymer nanocomposites based on Poly (vinylidene fluoride-co-trifluoroethylene) [P(VDF-TrFE) 55-45] with Ca and Sn co-substituted BaTiO3 ceramic fillers (Ba0.94Ca0.06Ti0.925Sn0.075O3, BCST). Saturated hysteresis loops and normal ferroelectric behaviour of the copolymer-based nanocomposites-as opposed to the relaxor ferroelectric nature of the terpolymer-based ones-allow the utilization of the indirect method to estimate the electrocaloric properties. Both the dielectric constant and electrocaloric temperature change (AT) increases as the particle content increases. Maximum adiabatic temperature change was obtained as 6.96 K under 900 kV/cm for the 10 vol % BCST containing polymer composite around the Curie temperature of the copolymer (70 degrees C). This relatively large electrocaloric strength is slightly lower than those obtained for terpolymer-based nanocomposites.Article Citation - WoS: 32Citation - Scopus: 36Corrosion and Tribocorrosion Behaviour of Ti-B4c Composites Processed by Conventional Sintering and Hot-Pressing Technique(Elsevier, 2021) Sousa, L.; Alves, A. C.; Guedes, A.; Toptan, FatihIn this work, low volume reinforcement ex-situ Ti-B4C composites were produced using two different routes: conventional powder metallurgy (PM) and hot-pressing (HP). The effect of reinforcement phases and processing method on corrosion and tribocorrosion behaviour were studied. Composites processed by PM lost the typical passive behaviour of Ti matrix, while composites processed by HP presented similar behaviour to unreinforced Ti. Tribocorrosion tests showed that both composite groups presented two times decrease in corrosion kinetics under sliding compared to pure titanium. An antagonistic effect between wear and corrosion was observed for composites with at least two times decrease in wear volume compared to titanium. (C) 2021 Elsevier B.V. All rights reserved.