Materials Science and Engineering / Malzeme Bilimi ve Mühendisliği

Permanent URI for this collectionhttps://hdl.handle.net/11147/4719

Browse

Filters

2008 - 200912010 - 2019162020 - 20235

Settings

COAR Access Rights: search.filters.coarAccessRights.open accessScopus Q: search.filters.scopusQuartile.Q3

Search Results

Now showing 1 - 10 of 22
  • Article
    Citation - Scopus: 3
    A Brief Overview on Geothermal Scaling
    (General Directorate of Mineral Research and Exploration (MTA), 2023) Isık, Tuğba; Baba, Alper; Chandrasekharam, Dornadula; Demir, Mustafa M.; Isık, Tuğba; Baba, Alper; Demir, Mustafa Muammer
    Hot spring waters are rich in terms of minerals. Since there are dramatic changes in thermodynamic parameters in geothermal power plants, such as a decrease in temperature and pressure, severe precipitation occurs throughout the system components in an uncontrolled manner. There are three main chemistries in deposits: carbonates (mainly calcium carbonates), silicates (metal silicates), and sulphides (antimony sulphide-stibnite). Energy harvesting is remarkably reduced out of the insulating nature of the deposit. Various actions need to be taken to mitigate this undesirable issue of scaling in geothermal systems. Geothermal systems are in fact quite complex, and the composition of brine and, accordingly, the chemistry of the deposit are not identical. Therefore, each system should be studied individually, and a tailor-made remedy should be developed. In this overview, the types of deposits in terms of chemistry and the actions (pH modification or antiscalant dosing) that should be taken to reduce scaling are mentioned, and potential chemistries of antiscalants are given.
  • Article
    Citation - WoS: 5
    Citation - Scopus: 6
    Effect of Coiling Temperature on the Structure and Properties of Thermo-Mechanically Rolled S700mc Steel
    (Technical Faculty in Bor, 2022) Di Nunzio, P. E.; Cesile, M. C.; Oktay, S.; Davut, Kemal; Şeşen, M. K.
    The boron-free S700MC steel is usually produced by exploiting the properties of a ferrite-bainite mixed microstructure formed by coiling the strips at a temperature of about 450 degrees C, i.e.below the bainite starting temperature. With the aim of further enhancing the mechanical properties of 6 to 10 mm thick strips, industrial tests were carried out at a coiling temperature of 600 degrees C to promote the formation of a structure of ferrite and carbides, which is also acceptable for this type of steel. Unexpectedly, a microstructure composed of ferrite and martensite was obtained. Compared to the ferritic-bainitic grade, the new structure is characterized by a slight decrease of the yield point but by an increase of the ultimate tensile strength by no less than 80 MPa, with a transition from a quasi-discontinuous to a clearly continuous yielding behaviour. Accordingly, the ratio of yield strength to tensile strength decreases from 0.90 to 0.75 and the impact energy decreases by 35 J and 60 J for the two gauge levels, respectively. The mechanical behaviour of the strips coiled at high temperature is explained as a direct consequence of the dual phase structure with a hard phase interspersed in a soft ferrite matrix. The presence of martensite is explained by the so-called incomplete bainite reaction. The partial transformation into ferrite after coiling and the long time required for the coil to cool down stabilize the untransformed austenite due to the carbon enrichment making bainite formation at lower temperatures impossible.
  • Article
    Citation - Scopus: 1
    Oxidizer Gases Effects on the Diameter-Controlled Synthesis of Carbon Nanotubes
    (MIM Research Group, 2021) İnce Yardımcı, Atike; Öğütlü, Ahmet Sabri; Öğütlü, Deniz
    In this study, the influence of the oxidizers on the synthesis of carbon nanotubes by C2H4 decomposition over Fe catalyst has been investigated. CO2, O2, and H2O have been used as oxidizers, and to control catalyst particle formation and their sizes in the pretreatment stage. The same oxidizers have also been used in the growth stage to maintain the catalyst particle size, remove amorphous carbon formation to keep catalyst particle active. The results of scanning electron microscopy indicated that the average diameters of nanotubes decreased from 13.4±1.2 nm to 6.2±0.5 nm and extremely dense nanotubes were obtained when we added a small amount of CO2. Adding O2 extremely decreased the areal carbon nanotube density while widens the diameter distribution. H2O addition resulted in larger average diameters and made the growth strongly pretreatment dependent. Within the parameters tried for catalyst pretreatment and CNT growth processes, CO2 seemed the best choice for a weak oxidizing assistant. The strong dependency of the average diameter on pretreatment conditions indicated that pretreatment is a very important step in deciding the final diameters and their distribution.
  • Article
    Citation - WoS: 8
    Citation - Scopus: 12
    Synthesis of Potassium-Sodium Niobate (Knn) From Nbo2
    (Elsevier, 2021) Piskin, Cerem; Karacasulu, Levent; Bortolotti, Mauro; Vakifahmetoglu, Cekdar
    KxNa1-xNbO3 (0 < x < 1) were synthesized via hydrothermal method using niobium dioxide (NbO2) as the niobium source instead of the most common one, Nb2O5. Potassium-rich KxNa1-xNbO3 (x > 0.5) was obtained from 8 M total hydroxide concentration after 6 h of reaction at 200 degrees C. Rietveld refinement of the XRD data revealed that all samples exhibited the secondary NaNbO3 phase. However, the lowest amount (3.74 vol%) was obtained for 24 h of reaction under 10 M alkaline solution. After 3 h of reaction, dodecahedra shaped hexaniobate phase (KxNa8-xNb6O19.nH(2)O) was observed. Those structures were, subsequently, replaced by similar to 3 mu m cube shaped KNN crystals, obtained under 10 M reaction in 24 h time period.
  • Article
    Citation - WoS: 11
    Citation - Scopus: 13
    Effect of Cnt Incorporation on Pan/Ppy Nanofibers Synthesized by Electrospinning Method
    (TÜBİTAK, 2020) İnce Yardımcı, Atike; Tanoğlu, Metin; Yılmaz, Selahattin; Selamet, Yusuf
    In this study, carbon nanotubes (CNTs) added polyacrylonitrile/polypyrrole (PAN/PPy) electrospun nanofibers were produced. Average diameters of the nanofibers were measured as 268 and 153 nm for 10 and 25 wt% of PPy contents, respectively. A relatively higher strain to failure values (23.3%) were observed for the low PPy content. When as-grown CNTs (1 and 4 wt%) were added into the PAN/PPy blends, disordered nanofibers were observed to form within the microstructure. To improve the interfacial properties of CNTs/PAN/PPy composites, CNTs were functionalized with H2SO4/HNO3/HCl solution. The functionalized CNTs were well dispersed within the nanofibers and aligned along the direction of nanofibers. Therefore, beads formation on nanofibers decreased. The impedance of the nanofibers was found to decrease with the PPy content and CNT addition. These nanofibers had a great potential to be used as an electrochemical actuator or a tissue engineering scaffold.
  • Article
    Citation - WoS: 8
    Citation - Scopus: 10
    Microstructures and Mechanical Properties of Graphene Platelets-Reinforced Spark Plasma Sintered Tantalum Diboride-Silicon Carbide Composites
    (IOP Publishing, 2019) Gürcan, Kübra; İnci, Ezgi; Saçkan, İbrahim; Ayaş, Erhan; Gasan, Hakan
    Graphene nanoplates reinforcement (GNPs) TaB2-SiC composites were fabricated with Spark Plazma sintering (SPS) at 1850 degrees C with a-uniaxial pressure of 50 MPa and 10 min dwell time. Systematic investigation on the effect of GNP amount of densification, microstructural and mechanical properties (microhardness and fracture toughness) of the composites were presented. Density and hardness of composites decreased with the addition of GNP, while similar to 35% increase of fracture toughness value was obtained with GNP addition. The microstructural evaluation indicated that overlapped and agglomerated GNPs increased with an increasing amount of GNP in the composites and caused to decrease of density and hardness. On the other hand, GNP was retained in the composite form even with high process temperature (1850 degrees C) and cause toughening of composites with changing the fracture mode from transgranular to transgranular/intergranular fracture. GNP pull out, crack branching, crack bridging and crack deflection were observed as main toughening mechanisms.
  • Article
    Citation - WoS: 9
    Citation - Scopus: 9
    Synthesis and Characterization of Novel High Temperature Structural Adhesives Based on Nadic End Capped Mda-Btda Copolyimide
    (IOP Publishing Ltd., 2018) Acar, Oktay; Varış, Serhat; Işık, Tuğba; Tirkeş, Seha; Demir, Mustafa Muammer
    A series of novel copolyimide structural adhesives were synthesized using 4,4′-diaminodiphenylmethane (MDA), 3,4′-oxydianiline (ODA) and 3,3′,4,4′-benzophenonetetracarboxylic acid dianhydride (BTDA) as co-monomers, and nadic anhydride as an end cap reagent. The adhesives with different MDA and ODA contents were examined in terms of their structure, thermal stability, mechanical properties, and adhesive performance. They have glass transition temperatures (T g) about 400 °C, with thermal stability up to 500 °C. The effect of diamine monomer compositions on adhesion performance and processability of the copolyimides were studied. The copolyimides exhibited adhesion strength up to 16.3 MPa at room temperature. Nadic end capped MDA-BTDA-ODA copolyimide resins gained adjustable and controllable processability with the addition of ether bridged aromatic segments. The copolyimide adhesive with equimolar composition of MDA:ODA is distinguished form the both commercial PMR-15 and LARC RP-46 polyimides in terms of its better processability and mechanical performance.
  • Article
    Citation - WoS: 17
    Citation - Scopus: 18
    Development of an Ionic Liquid Based Method for the Preparation of Albumin Nanoparticles
    (John Wiley and Sons Inc., 2018) Demirkurt, Begüm; Akdoğan, Yaşar
    Albumin based nanocarriers have been widely used in drug delivery studies. Here, we developed a water-in-ionic liquid (IL) emulsion-like method to prepare bovine serum albumin (BSA) nanoparticles as alternative to the traditional organic solvents containing techniques. Conformational changes of albumin induced by the imidazolium based ILs at the water-IL interface triggers the BSA nanoparticle formation. The albumin nanoparticle formation are dependent on the experimental parameters and the hydophobicity of the IL. At pH 9.0, using 1.3%wt of BSA in water/1-butyl-3-methyl imidazolium tetrafluoroborate (BmimBF4) (50/50 mol%) and TX-100/butanol surfactant mixture yields uniformly distributed 200 nm average sized BSA nanoparticles. Different than BmimBF4, using a more hydrophilic IL, EmimBF4 yielded albumin aggregates. Instead, using a more hydrophobic IL, HmimBF4 produced albumin nanoparticles but a non-uniform size distribution was obtained. These results indicate that the ionic liquids called green and designer solvents can be also used to synthesize albumin nanoparticles.
  • Article
    Citation - WoS: 3
    Citation - Scopus: 3
    Monolayer Aste2: Stable Robust Metal in 2d, 1d and 0d
    (Wiley, 2018) Badalov, S. V.; Kandemir, Ali; Şahin, Hasan
    The structural, phononic, and electronic properties of the monolayer structures of AsTe2 are characterized by performing density functional theory (DFT) calculations. Total energy optimization and phonon calculations reveal that single layers of the 2H-AsTe2 and 1T-AsTe2 phases form dynamically stable crystal structures. Electronic structure analysis also shows that both 2H and 1T phases have nonmagnetic metallic character. It is also predicted that the metallic nature of the ultra-thin both 2H-AsTe2 and 1T-AsTe2 structures remain unchanged even under high biaxial strain values. For further examination of the dimensionality effect in the robust metallicity in 2D AsTe2 phases, electronic characteristics of 1D nanoribbons and 0D quantum dots are also investigated. It is found that independent from the dimension and crystallographic orientations 0D and 1D structures of 2H- and 1T-AsTe2 structures have metallic behavior. It is found that single layers of AsTe2 are quite promising materials for nanodevice applications owing to the robust metallic character.
  • Article
    Citation - WoS: 84
    Citation - Scopus: 85
    A Review on Halide Perovskites as Color Conversion Layers in White Light Emitting Diode Applications
    (John Wiley and Sons Inc., 2018) Güner, Tuğrul; Demir, Mustafa Muammer
    In the last decade, halide perovskites have attracted great interest due to many reasons, including their low cost, solution-processability, superior PL properties, broad range of color tunability, color purity, and defect tolerance, among others. They are in increasing demand for a wide range of applications, such as solar cells, light emitting diodes (LEDs), white LEDs (WLED), and lasers. Yellow phosphors have been heavily employed in solid-state lighting, since its illumination by blue yields white light with various optical features, such as high/low CRI, CCT, and luminous efficiency. However, phosphors as pigments are seldom found and are costly material. In this sense, halide perovskites may offer a promising alternative to phosphors for future solid-state lighting. In this study, the synthesis and optical properties of halide perovskites, as well as their application in WLED as a conversion layer are investigated.