Materials Science and Engineering / Malzeme Bilimi ve Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4719
Browse
43 results
Search Results
Article Citation - WoS: 5Citation - Scopus: 6Effect of Coiling Temperature on the Structure and Properties of Thermo-Mechanically Rolled S700mc Steel(Technical Faculty in Bor, 2022) Di Nunzio, P. E.; Cesile, M. C.; Oktay, S.; Davut, Kemal; Şeşen, M. K.The boron-free S700MC steel is usually produced by exploiting the properties of a ferrite-bainite mixed microstructure formed by coiling the strips at a temperature of about 450 degrees C, i.e.below the bainite starting temperature. With the aim of further enhancing the mechanical properties of 6 to 10 mm thick strips, industrial tests were carried out at a coiling temperature of 600 degrees C to promote the formation of a structure of ferrite and carbides, which is also acceptable for this type of steel. Unexpectedly, a microstructure composed of ferrite and martensite was obtained. Compared to the ferritic-bainitic grade, the new structure is characterized by a slight decrease of the yield point but by an increase of the ultimate tensile strength by no less than 80 MPa, with a transition from a quasi-discontinuous to a clearly continuous yielding behaviour. Accordingly, the ratio of yield strength to tensile strength decreases from 0.90 to 0.75 and the impact energy decreases by 35 J and 60 J for the two gauge levels, respectively. The mechanical behaviour of the strips coiled at high temperature is explained as a direct consequence of the dual phase structure with a hard phase interspersed in a soft ferrite matrix. The presence of martensite is explained by the so-called incomplete bainite reaction. The partial transformation into ferrite after coiling and the long time required for the coil to cool down stabilize the untransformed austenite due to the carbon enrichment making bainite formation at lower temperatures impossible.Article Citation - WoS: 11Citation - Scopus: 13Effect of Cnt Incorporation on Pan/Ppy Nanofibers Synthesized by Electrospinning Method(TÜBİTAK, 2020) İnce Yardımcı, Atike; Tanoğlu, Metin; Yılmaz, Selahattin; Selamet, YusufIn this study, carbon nanotubes (CNTs) added polyacrylonitrile/polypyrrole (PAN/PPy) electrospun nanofibers were produced. Average diameters of the nanofibers were measured as 268 and 153 nm for 10 and 25 wt% of PPy contents, respectively. A relatively higher strain to failure values (23.3%) were observed for the low PPy content. When as-grown CNTs (1 and 4 wt%) were added into the PAN/PPy blends, disordered nanofibers were observed to form within the microstructure. To improve the interfacial properties of CNTs/PAN/PPy composites, CNTs were functionalized with H2SO4/HNO3/HCl solution. The functionalized CNTs were well dispersed within the nanofibers and aligned along the direction of nanofibers. Therefore, beads formation on nanofibers decreased. The impedance of the nanofibers was found to decrease with the PPy content and CNT addition. These nanofibers had a great potential to be used as an electrochemical actuator or a tissue engineering scaffold.Article Citation - WoS: 14Citation - Scopus: 13Effect of Texture on the Electrical and Electrocaloric Properties of 0.90pb(mg1/3nb2 Relaxor Ceramics(American Institute of Physics, 2020) Mensur Alkoy, Ebru; Okatan, M. Barış; Aydın, Ecem; Kılıç, Yusuf; Mısırlıoğlu, I. Burç; Alkoy, SedatFunctional properties of ferroelectric compositions depend strongly on the type of stable crystalline phase at a given temperature and texturing. In addition to defining a governing crystallographic axis among the grains with respect to a global reference axis, texturing in these systems is also often meant to imply the relationship between an external applied field and the polar axis. Here, we synthesize randomly oriented and 001(pc) textured 0.90Pb(Mg1/3Nb2/3)O-3-0.10PbTiO(3) solid solutions that fall into the relaxor category. A >95% degree of 001(pc) texturing was achieved by the use of single crystal BaTiO3 template crystallites whose volume fraction does not exceed 5% of the entire sample volume. Electrical measurements made on random and textured samples reveal the impact of texture on the hysteresis and the dielectric response. A Curie-Weiss analysis of the temperature dependent dielectric data shows the degree of relaxor behavior in random and textured samples. As similar compositions have recently been getting interest for electrothermal management applications, we compute the electrocaloric (EC) response of the random and textured samples using indirect methods followed by an estimation of the EC response with a subsequent thermodynamic analysis to shed light on the effect of texture on the observed differences between the textured and the random oriented samples. We finally compare and contrast on the desirability of texturing in these systems for use as EC components for thermal management applications.Article Citation - WoS: 3Citation - Scopus: 3Green Fabrication of Lanthanide-Doped Hydroxide-Based Phosphors: Y(oh)(3):eu3+ Nanoparticles for White Light Generation(Beilstein-Institut Zur Forderung der Chemischen Wissenschaften, 2019) Güner, Tuğrul; Kuş, Anılcan; Özcan, Mehmet; Genç, Aziz; Şahin, Hasan; Demir, Mustafa MuammerPhosphors can serve as color conversion layers to generate white light with varying optical features, including color rendering index (CRI), high correlated color temperature (CCT), and luminous efficacy. However, they are typically produced under harsh synthesis conditions such as high temperature, high pressure, and/or by employing a large amount of solvent. In this work, a facile, water-based, rapid method has been proposed to fabricate lanthanide-doped hydroxide-based phosphors. In this sense, sub-micrometer-sized Y(OH)(3):Eu3+ particles (as red phosphor) were synthesized in water at ambient conditions in <= 60 min reaction time. The doping ratio was controlled from 2.5-20 mol %. Additionally, first principle calculations were performed on Y(OH)(3):Eu3+ to understand the preferable doping scenario and its optoelectronic properties. As an application, these fabricated red phosphors were integrated into a PDMS/YAG:Ce3+ composite and used to generate white light. The resulting white light showed a remarkable improvement (approximate to 24%) in terms of luminous efficiency, a slight reduction of CCT (from 3900 to 3600 K), and an unchanged CRI (approximate to 60) as the amount of Y(OH)(3):Eu3+ was increased.Article Citation - WoS: 25Citation - Scopus: 27Osteogenic Differentiation of Mesenchymal Stem Cells on Random and Aligned Pan/Ppy Nanofibrous Scaffolds(SAGE Publications, 2019) Selamet, Yusuf; İnce Yardımcı, Atike; Baskan, Öznur; Yılmaz, Selahattin; Meşe, Gülistan; Özçivici, EnginThe aim of this study was to develop random and aligned polyacrilonitrile (PAN)/polypyrrole (PPy) nanofibrous scaffolds by electrospinning technique for osteogenic differentiation of mesenchymal stem cells. Nanofibers were fabricated successfully as straight, smooth, and free from bead formation. The average diameter of random and aligned nanofibers was 268(+/- 49) nm and 225(+/- 72) nm, respectively. Alignment process increased the tensile strength of nanofibers 3.9-fold, while the tensile strain of nanofibers decreased by 78%. PAN/PPy nanofibers were hydrophilic with the contact angle value of about 32 degrees and alignment did not affect the contact angle value. Random and aligned PAN/PPy nanofibers were investigated as a scaffold material for osteogenic differentiation of D1 ORL UVA mouse bone marrow mesenchymal stem cells. Cells were able to attach and grow on nanofibers confirmed by cell viability results. Stem cells that were cultured with osteogenic induction were able to mineralize on electrospun nanofibers based on alizarin red and Von Kossa dye staining. For aligned PPy nanofibers, mineralization occurred in the fiber alignment direction. Consequently, PAN/PPy nanofibrous mats in both random and aligned forms would be potential candidates for bone tissue engineering.Article Citation - WoS: 6Citation - Scopus: 8Enhanced Spontaneous Emission Rate in a Low-Q Hybrid Photonic-Plasmonic Nanoresonator(American Chemical Society, 2019) Gökbulut, Belkıs; İnanç, Arda; Topçu, Gökhan; Ünlütürk, Seçil Sevim; Özçelik, Serdar; Demir, Mustafa Muammer; İnci, Mehmet NaciIn this paper, CdTe quantum dots (QDs)-doped single electrospun polymer nanofibers are partially coated with gold nanoparticles to form distinct hybrid photonic-plasmonic nanoresonators to investigate the critical role of the cavity-confined hybrid mode on the modification of the spontaneous emission dynamics of the fluorescent emitters in low-Q photonic cavities. A total enhancement factor of 11.2 is measured via a time-resolved experimental technique, which shows that there is an increase of about three times in the spontaneous emission rate for the QDs-doped gold nanoparticle-decorated nanofibers as they are compared with those uncoated ones. The physical mechanism affecting the spontaneous emission rate of the encapsulated QDs in such a hybrid photonic-plasmonic nanoresonator is explained to be due to regeneration of the mode field in the nanofiber cavity upon the interaction of the dipoles with the surface plasmons of distinctive gold nanoparticles that surround the outer surface of the nanofiber.Article Citation - WoS: 21Citation - Scopus: 22Green Function, Quasi-Classical Langevin and Kubo-Greenwood Methods in Quantum Thermal Transport(IOP Publishing, 2019) Sevinçli, Haldun; Roche, S.; Cuniberti, G.; Brandbyge, M.; Gutierrez, R.; Sandonas, L. MedranoWith the advances in fabrication of materials with feature sizes at the order of nanometers, it has been possible to alter their thermal transport properties dramatically. Miniaturization of device size increases the power density in general, hence faster electronics require better thermal transport, whereas better thermoelectric applications require the opposite. Such diverse needs bring new challenges for material design. Shrinkage of length scales has also changed the experimental and theoretical methods to study thermal transport. Unsurprisingly, novel approaches have emerged to control phonon flow. Besides, ever increasing computational power is another driving force for developing new computational methods. In this review, we discuss three methods developed for computing vibrational thermal transport properties of nano-structured systems, namely Green function, quasi-classical Langevin, and Kubo-Green methods. The Green function methods are explained using both nonequilibrium expressions and the Landauer-type formula. The partitioning scheme, decimation techniques and surface Green functions are reviewed, and a simple model for reservoir Green functions is shown. The expressions for the Kubo-Greenwood method are derived, and Lanczos tridiagonalization, continued fraction and Chebyshev polynomial expansion methods are discussed. Additionally, the quasi-classical Langevin approach, which is useful for incorporating phonon-phonon and other scatterings is summarized.Article Citation - WoS: 1Investigation of the Electrical Parameters of the Organic Diode Modified With 4-[(3 Benzoic Acid(Electrochemical Society, Inc., 2016) Havare, A. Kemal; Can, Mustafa; Yağmurcukardeş, Nesli; Yiğit, Mesude Zeliha; Aydın, Hasan; Okur, Salih; Demiç, Şerafettin; İçli, Sıddık4-[(3-Methylphenyl)(phenyl)amino]benzoic acid (MPPBA) self-assembled monolayer (SAM) molecules as hole injection is formed on p and n type Si and on indium-tin oxide (ITO) electrodes to investigate the effect on the electrical parameters of hole only organic device. The hole mobility improvement of organic device was attributed to an intermediate energy level formed between hole transport materials (HTL) (N,N'-Bis(naphthalen-1-yl)-N,N'-bis(phenyl)benzidine -NPB) and ITO when forming an ultrathin MPPBA layer, leading to increase of carrier mobility of the device. Space charge limited current (SCLC) technique is used to estimate the mobility of the NPB formed at the interface metal/organic Ohmic contact. The hole mobility of ITO/NPB/Al and ITO/MPPBA/NPB/Al devices were obtained as 1.80 x 10(-6) and 1.76 x 10(-3) cm(2)/Vs, at 1350 E (V/cm)(1/2) applied electric field, respectively. SAM modified devices has lower barrier height values. The electronic characteristic parameters of the ITO/(with or without MPPBA)/NPB/Al, Au/n-Si(or p-Si)/(with or without MPPBA)/Au contacts were calculated using current-voltage (I-V) measurements by Schottky type carrier injection. (C) The Author(s) 2016. Published by ECS.Article Citation - WoS: 93Citation - Scopus: 95Single-Layer Janus-Type Platinum Dichalcogenides and Their Heterostructures(American Chemical Society, 2019) Kahraman, Zeynep; Kandemir, Ali; Yağmurcukardeş, Mehmet; Şahin, HasanUltrathin two-dimensional Janus-type platinum dichalcogenide crystals formed by two different atoms at opposite surfaces are investigated by performing state-of-the-art density functional theory calculations. First, it is shown that single-layer PtX2 structures (where X = S, Se, or Te) crystallize into the dynamically stable IT phase and are indirect band gap semiconductors. It is also found that the substitutional chalcogen doping in all PtX2 structures is favorable via replacement of surface atoms with a smaller chalcogen atom, and such a process leads to the formation of Janus-type platinum dichalcogenides (XPtY, where X and Y stand for S, Se, or Te) which are novel single-layer crystals. While all Janus structures are indirect band gap semiconductors as their binary analogues, their Raman spectra show distinctive features that stem from the broken out-of-plane symmetry. In addition, it is revealed that the construction of Janus crystals enhances the piezoelectric constants of PtX2 crystals significantly both in the in plane and in the out-of-plane directions. Moreover, it is shown that vertically stacked van der Waals heterostructures of binary and ternary (Janus) platinum dichalcogenides offer a wide range of electronic features by forming bilayer heterojunctions of type-I, type-II, and type-III, respectively. Our findings reveal that Janus-type ultrathin platinum dichalcogenide crystals are quite promising materials for optoelectronic device applications.Article Citation - WoS: 18Citation - Scopus: 14Optimization and Performance of Nitrogen-Doped Carbon Dots as a Color Conversion Layer for White-Led Applications(Beilstein-Institut Zur Forderung der Chemischen Wissenschaften, 2019) Güner, Tuğrul; Yüce, Hürriyet; Taşçıoğlu, Didem; Şimşek, Eren; Savacı, Umut; Genç, Aziz; Demir, Mustafa MuammerIn this study, green-emitting nitrogen-doped carbon dots (N-CDots) were synthesized and incorporated into drop-cast composite films for use as color conversion layers in a white-LED configuration to generate white light. In order to resolve the red deficiency of this configuration, a commercial red phosphor was integrated into the system. Moreover, the N-CDots were also processed into polymer/N-CDot composite fibers, for which we determined the amount of N-CDots that yielded adequate white-light properties. Finally, we showed that white light with excellent properties could be generated by employing both of the fabricated N-CDot composites either as drop-cast films or composite fibers. Hence, N-CDots provide a promising alternative to inorganic phosphors that are commonly employed in white-LED configurations.