Materials Science and Engineering / Malzeme Bilimi ve Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4719
Browse
58 results
Search Results
Article Citation - WoS: 7Citation - Scopus: 7Breaking the Boundaries of the Goldschmidt Tolerance Factor With Ethylammonium Lead Iodide Perovskite Nanocrystals(American Chemical Society, 2024) Güvenç, Çetin Meriç; Toso, Stefano; Ivanov, Yurii P.; Saleh, Gabriele; Balcı, Sinan; Divitini, Giorgio; Manna, LiberatoWe report the synthesis of ethylammonium lead iodide (EAPbI3) colloidal nanocrystals as another member of the lead halide perovskites family. The insertion of an unusually large A-cation (274 pm in diameter) in the perovskite structure, hitherto considered unlikely due to the unfavorable Goldschmidt tolerance factor, results in a significantly larger lattice parameter compared to the Cs-, methylammonium- and formamidinium-based lead halide perovskite homologues. As a consequence, EAPbI3 nanocrystals are highly unstable, evolving to a nonperovskite delta-EAPbI3 polymorph within 1 day. Also, EAPbI3 nanocrystals are very sensitive to electron irradiation and quickly degrade to PbI2 upon exposure to the electron beam, following a mechanism similar to that of other hybrid lead iodide perovskites (although degradation can be reduced by partially replacing the EA+ ions with Cs+ ions). Interestingly, in some cases during this degradation the formation of an epitaxial interface between (EA x Cs1-x )PbI3 and PbI2 is observed. The photoluminescence emission of the EAPbI3 perovskite nanocrystals, albeit being characterized by a low quantum yield (similar to 1%), can be tuned in the 664-690 nm range by regulating their size during the synthesis. The emission efficiency can be improved upon partial alloying at the A site with Cs+ or formamidinium cations. Furthermore, the morphology of the EAPbI3 nanocrystals can be chosen to be either nanocube or nanoplatelet, depending on the synthesis conditions.Article Citation - WoS: 8Citation - Scopus: 8Design and Performance Comparison of Polymer-Derived Ceramic Ambigels and Aerogels(American Chemical Society, 2023) Soraru, Gian Domenico; İçin, Öykü; Semerci, Tuğçe; Ahmetoğlu, Çekdar VakıfThis work reports the synthesis and characterization of preceramic-and polymer-derived SiOC aerogels obtained from a commercial siloxane resin. The preceramic aerogels were obtained by ambient pressure drying (ambigels) and CO2 supercritical drying. Despite different drying processes, the final ceramic ambi/aerogels have very similar microstructural features in density, porosity, pore size, and specific surface area. Both materials have shown promising results for oil sorption and water cleaning. Supercritically dried-SiOC aerogel had low thermal conductivity with 0.046 W.m(-1).K-1 at RT and 0.073 W.m(-1).K-1 at 500 degrees C. These results suggest that substituting the rather complicated and expensive CO2-SC drying with the more friendly and cheap ambient pressure drying can be done without having to accept significant microstructural/property degradation.Review Citation - WoS: 41Citation - Scopus: 42Review on the Parameters of Recycling Ndfeb Magnets Via a Hydrogenation Process(American Chemical Society, 2023) Habibzadeh, Alireza; Küçüker, Mehmet Ali; Gökelma, MertolRegarding the restrictions recently imposed by China on the export of rare-earth elements (REEs), the world may face a serious challenge in supplying some REEs such as neodymium and dysprosium soon. Recycling secondary sources is strongly recommended to mitigate the supply risk of REEs. Hydrogen processing of magnetic scrap (HPMS) as one of the best approaches for magnet-to-magnet recycling is thoroughly reviewed in this study in terms of parameters and properties. The processes of hydrogen decrepitation (HD) and hydrogenation-disproportio-nation-desorption-recombination (HDDR) are two common methods for HPMS. Employing a hydrogenation process can shorten the production route of new magnets from the discarded magnets compared to other recycling routes such as the hydrometallurgical route. However, determining the optimal pressure and temperature for the process is challenging due to the sensitivity to the initial chemical composition and the interaction of temperature and pressure. Pressure, temperature, initial chemical composition, gas flow rate, particle size distribution, grain size, and oxygen content are the effective parameters for the final magnetic properties. All these influencing parameters are discussed in detail in this review. The recovery rate of magnetic properties has been the concern of most research in this field and can be achieved up to 90% by employing a low hydrogenation temperature and pressure and using additives such as REE hydrides after hydrogenation and before sintering.Article Citation - WoS: 18Citation - Scopus: 22Biomimetic Dentin Repair: Amelogenin-Derived Peptide Guides Occlusion and Peritubular Mineralization of Human Teeth(American Chemical Society, 2023) Fong, Hanson; Hamann, John; Hall, Eric; Yücesoy, Deniz T.; Doğan, Sami; Sarıkaya, MehmetExposure of dentin tubules due to loss of protective enamel (crown) and cementum (root) tissues as a result of erosion, mechanical wear, gingival recession, etc. has been the leading causes of dentin hypersensitivity. Despite being a widespread ailment, no permanent solution exists to address this oral condition. Current treatments are designed to alleviate the pain by either using desensitizers or blocking dentin tubules by deposition of minerals or solid precipitates, which often have short-lived effects. Reproducing an integrated mineral layer that occludes exposed dentin with concomitant peritubular mineralization is essential to reestablish the structural and mechanical integrity of the tooth with long-term durability. Here, we describe a biomimetic treatment that promotes dentin repair using a mineralization directing peptide, sADP5, derived from amelogenin. The occlusion was achieved through a layer-by-layer peptide-guided remineralization process that forms an infiltrating mineral layer on dentin. The structure, composition, and nanomechanical properties of the remineralized dentin were analyzed by cross-sectional scanning electron microscopy imaging, energy dispersive X-ray spectroscopy, and nanomechanical testing. The elemental analysis provided calcium and phosphate compositions that are similar to those in hydroxyapatite. The measured average hardness and reduced elastic modulus values for the mineral layer were significantly higher than those of the demineralized and sound human dentin. The structural integration of the new mineral and underlying dentin was confirmed by thermal aging demonstrating no physical separation. These results suggest that a structurally robust and mechanically durable interface is formed between the interpenetrating mineral layer and underlying dentin that can withstand long-term mechanical and thermal stresses naturally experienced in the oral environment. The peptide-guided remineralization procedure described herein could provide a foundation for the development of highly effective oral care products leading to novel biomimetic treatments for a wide range of demineralization-related ailments and, in particular, offers a potent long-term solution for dentin hypersensitivity.Article Citation - WoS: 101Citation - Scopus: 105Defect-Engineering Agsbte2 With High Thermoelectric Performance(Wiley, 2023) Zhang, Yu; Li, Zhi; Singh, Saurabh; Nozariasbmarz, Amin; Li, Wenjie; Genç, Aziz; Xia, YiThermoelectric (TE) generators enable the direct and reversible conversion between heat and electricity, providing applications in both refrigeration and power generation. In the last decade, several TE materials with relatively high figures of merit (zT) have been reported in the low- and high-temperature regimes. However, there is an urgent demand for high-performance TE materials working in the mid-temperature range (400–700 K). Herein, p-type AgSbTe2 materials stabilized with S and Se co-doping are demonstrated to exhibit an outstanding maximum figure of merit (zTmax) of 2.3 at 673 K and an average figure of merit (zTave) of 1.59 over the wide temperature range of 300–673 K. This exceptional performance arises from an enhanced carrier density resulting from a higher concentration of silver vacancies, a vastly improved Seebeck coefficient enabled by the flattening of the valence band maximum and the inhibited formation of n-type Ag2Te, and ahighly improved stability beyond 673 K. The optimized material is used to fabricate a single-leg device with efficiencies up to 13.3% and a unicouple TE device reaching energy conversion efficiencies up to 12.3% at a temperature difference of 370 K. These results highlight an effective strategy to engineer high-performance TE material in the mid-temperature range.Article Citation - WoS: 2Citation - Scopus: 2Size Driven Barrier To Chirality Reversal in Electric Control of Magnetic Vortices in Ferromagnetic Nanodiscs(Royal Society of Chemistry, 2022) Aldulaimi, W. A. S.; Okatan, Mahmut Barış; Şendur, Kürşat; Onbaşlı, Mehmet Cengiz; Mısırlıoğlu, İbrahim BurçNew high density storage media and spintronic devices come about with a progressing demand for the miniaturization of ferromagnetic structures. Vortex ordering of magnetic dipoles in such structures has been repeatedly observed as a stable state, offering the possibility of chirality in these states as a means to store information at high density. Electric pulses and magnetoelectric coupling are attractive options to control the chirality of such states in a deterministic manner. Here, we demonstrate the chirality reversal of vortex states in ferromagnetic nanodiscs via pulsed electric fields using a micromagnetic approach and focus on the analysis of the energetics of the reversal process. A strong thickness dependence of the chirality reversal in the nanodiscs is found that emanates from the anisotropy of the demagnetizing fields. Our results indicate that chiral switching of the magnetic moments in thin discs can give rise to a transient vortex-antivortex lattice not observed in thicker discs. This difference in the chirality reversal mechanism emanates from profoundly different energy barriers to overcome in thin and thicker discs. We also report the polarity-chirality correlation of a vortex that appears to depend on the aspect ratio of the nanodiscs.Article Citation - WoS: 22Citation - Scopus: 21Preparation of Interconnected Pickering Polymerized High Internal Phase Emulsions by Arrested Coalescence(American Chemical Society, 2022) Sherborne, Colin; Reilly, Gwendolen C.; Claeyssens, Frederik; Durgut, Enes; Aldemir Dikici, BetülEmulsion templating is a method that enables the production of highly porous and interconnected polymer foams called polymerized high internal phase emulsions (PolyHIPEs). Since emulsions are inherently unstable systems, they can be stabilized either by surfactants or by particles (Pickering HIPEs). Surfactant-stabilized HIPEs form materials with an interconnected porous structure, while Pickering HIPEs typically form closed pore materials. In this study, we describe a system that uses submicrometer polymer particles to stabilize the emulsions. Polymers fabricated from these Pickering emulsions exhibit, unlike traditional Pickering emulsions, highly interconnected large pore structures, and we related these structures to arrested coalescence. We describe in detail the morphological properties of this system and their dependence on different production parameters. This production method might provide an interesting alternative to poly-surfactant-stabilized-HIPEs, in particular where the application necessitates large pore structures.Article Citation - WoS: 6Citation - Scopus: 6Tribocorrosion-Resistant Ti40nb-Tin Composites Havingtio(2)-Based Nanotubular Surfaces(American Chemical Society, 2022) Çaha, İhsan; Alves, Alexandra Cruz; Chirico, Caterina; Pinto, Ana Maria; Tsipas, Sophia; Gordo, Elena; Toptan, FatihA novel multifunctional material was developed byhard TiN particle reinforcement addition to a beta-type Ti40Nb alloy,followed by surface functionalization, yielding the formation of ananotubular layer. Corrosion and tribocorrosion behaviors wereinvestigated in a phosphate-buffered saline solution at bodytemperature. The results revealed that the Ti40Nb-TiNcomposites presented similaripassandE(i=0)values together withrelatively similarRoxandCox. However, its tribocorrosion resistancedrastically improved (wear volume is almost 15 times lower than anunreinforced alloy) as a consequence of the load-carrying effectgiven by the reinforcement phases. The corrosion and tribocorro-sion behaviors were further improved through surface functionaliza-tion as observed by significantly loweripassand higherRoxvalues andalmost undetectable wear volume loss from tribocorrosion tests dueto the formation of a well-adhered anatase-rutile TiO2-based nanotubular layer.Article Citation - WoS: 18Citation - Scopus: 22Effect of Fomes Fomentarius Cultivation Conditions on Its Adsorption Performance for Anionic and Cationic Dyes(American Chemical Society, 2022) Henning, Laura M.; Simon, Ulla; Abdullayev, Amanmyrat; Schmidt, Bertram; Pohl, Carsten; Nunez Guitar, Tamara; Ahmetoğlu, Çekdar Vakıf; Meyer, Vera; Bekheet, Maged F.; Gurlo, AleksanderLab-cultivated mycelia of Fomes fomentarius (FF), grown on a solid lignocellulose medium (FF-SM) and a liquid glucose medium (FF-LM), and naturally grown fruiting bodies (FF-FB) were studied as biosorbents for the removal of organic dyes methylene blue and Congo red (CR). Both the chemical and microstructural differences were revealed using X-ray photoelectron spectroscopy, Fourier-transform infrared spectroscopy, zeta potential analysis, and scanning electron microscopy, illuminating the superiority of FF-LM and FF-SM over FF-FB in dye adsorption. The adsorption process of CR on FF-LM and FF-SM is best described by the Redlich-Peterson model with β constants close to 1, that is, approaching the monolayer Langmuir model, which reach maximum adsorption capacities of 48.8 and 13.4 mg g-1, respectively, in neutral solutions. Adsorption kinetics follow the pseudo-second-order model where chemisorption is the rate-controlling step. While the desorption efficiencies were low, adsorption performances were preserved and even enhanced under simulated dye effluent conditions. The results suggest that F. fomentarius can be considered an attractive biosorbent in industrial wastewater treatment and that its cultivation conditions can be specifically tailored to tune its cell wall composition and adsorption performance.Article Citation - WoS: 8Citation - Scopus: 11Spreadability of Metal Powders for Laser-Powder Bed Fusion Via Simple Image Processing Steps(MDPI, 2022) Ahmetoğlu, Çekdar Vakıf; Hasdemir, Beyza; Biasetto, LisaThis paper investigates the spreadability of the spherical CoCrWMo powder for laser- powder bed fusion (PBF-LB) by using image processing algorithms coded in MATLAB. Besides, it also aims to examine the spreadability dependence with the other characteristics such as powder size distribution, apparent density, angle of repose. Powder blends in four different particle size distributions are prepared, characterized, and spreadability tests are performed with the PBF-LB. The results demonstrate that an increase in fine particle ratio by volume (below 10 µm) enhances the agglomeration and decreases the flowability, causing poor spreadability. These irregularities on the spread layers are quantified with simple illumination invariant analysis. A clear relation between powder spreadability and 3D printed structures properties in terms of residual porosity could not be defined since structural defects in 3D printed parts also depends on other processing parameters such as spatter formation or powder size over layer height ratio.