Materials Science and Engineering / Malzeme Bilimi ve Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4719
Browse
24 results
Search Results
Article Citation - WoS: 8Citation - Scopus: 8Design and Performance Comparison of Polymer-Derived Ceramic Ambigels and Aerogels(American Chemical Society, 2023) Soraru, Gian Domenico; İçin, Öykü; Semerci, Tuğçe; Ahmetoğlu, Çekdar VakıfThis work reports the synthesis and characterization of preceramic-and polymer-derived SiOC aerogels obtained from a commercial siloxane resin. The preceramic aerogels were obtained by ambient pressure drying (ambigels) and CO2 supercritical drying. Despite different drying processes, the final ceramic ambi/aerogels have very similar microstructural features in density, porosity, pore size, and specific surface area. Both materials have shown promising results for oil sorption and water cleaning. Supercritically dried-SiOC aerogel had low thermal conductivity with 0.046 W.m(-1).K-1 at RT and 0.073 W.m(-1).K-1 at 500 degrees C. These results suggest that substituting the rather complicated and expensive CO2-SC drying with the more friendly and cheap ambient pressure drying can be done without having to accept significant microstructural/property degradation.Review Citation - WoS: 41Citation - Scopus: 42Review on the Parameters of Recycling Ndfeb Magnets Via a Hydrogenation Process(American Chemical Society, 2023) Habibzadeh, Alireza; Küçüker, Mehmet Ali; Gökelma, MertolRegarding the restrictions recently imposed by China on the export of rare-earth elements (REEs), the world may face a serious challenge in supplying some REEs such as neodymium and dysprosium soon. Recycling secondary sources is strongly recommended to mitigate the supply risk of REEs. Hydrogen processing of magnetic scrap (HPMS) as one of the best approaches for magnet-to-magnet recycling is thoroughly reviewed in this study in terms of parameters and properties. The processes of hydrogen decrepitation (HD) and hydrogenation-disproportio-nation-desorption-recombination (HDDR) are two common methods for HPMS. Employing a hydrogenation process can shorten the production route of new magnets from the discarded magnets compared to other recycling routes such as the hydrometallurgical route. However, determining the optimal pressure and temperature for the process is challenging due to the sensitivity to the initial chemical composition and the interaction of temperature and pressure. Pressure, temperature, initial chemical composition, gas flow rate, particle size distribution, grain size, and oxygen content are the effective parameters for the final magnetic properties. All these influencing parameters are discussed in detail in this review. The recovery rate of magnetic properties has been the concern of most research in this field and can be achieved up to 90% by employing a low hydrogenation temperature and pressure and using additives such as REE hydrides after hydrogenation and before sintering.Article Citation - WoS: 18Citation - Scopus: 22Biomimetic Dentin Repair: Amelogenin-Derived Peptide Guides Occlusion and Peritubular Mineralization of Human Teeth(American Chemical Society, 2023) Fong, Hanson; Hamann, John; Hall, Eric; Yücesoy, Deniz T.; Doğan, Sami; Sarıkaya, MehmetExposure of dentin tubules due to loss of protective enamel (crown) and cementum (root) tissues as a result of erosion, mechanical wear, gingival recession, etc. has been the leading causes of dentin hypersensitivity. Despite being a widespread ailment, no permanent solution exists to address this oral condition. Current treatments are designed to alleviate the pain by either using desensitizers or blocking dentin tubules by deposition of minerals or solid precipitates, which often have short-lived effects. Reproducing an integrated mineral layer that occludes exposed dentin with concomitant peritubular mineralization is essential to reestablish the structural and mechanical integrity of the tooth with long-term durability. Here, we describe a biomimetic treatment that promotes dentin repair using a mineralization directing peptide, sADP5, derived from amelogenin. The occlusion was achieved through a layer-by-layer peptide-guided remineralization process that forms an infiltrating mineral layer on dentin. The structure, composition, and nanomechanical properties of the remineralized dentin were analyzed by cross-sectional scanning electron microscopy imaging, energy dispersive X-ray spectroscopy, and nanomechanical testing. The elemental analysis provided calcium and phosphate compositions that are similar to those in hydroxyapatite. The measured average hardness and reduced elastic modulus values for the mineral layer were significantly higher than those of the demineralized and sound human dentin. The structural integration of the new mineral and underlying dentin was confirmed by thermal aging demonstrating no physical separation. These results suggest that a structurally robust and mechanically durable interface is formed between the interpenetrating mineral layer and underlying dentin that can withstand long-term mechanical and thermal stresses naturally experienced in the oral environment. The peptide-guided remineralization procedure described herein could provide a foundation for the development of highly effective oral care products leading to novel biomimetic treatments for a wide range of demineralization-related ailments and, in particular, offers a potent long-term solution for dentin hypersensitivity.Article Citation - WoS: 22Citation - Scopus: 21Preparation of Interconnected Pickering Polymerized High Internal Phase Emulsions by Arrested Coalescence(American Chemical Society, 2022) Sherborne, Colin; Reilly, Gwendolen C.; Claeyssens, Frederik; Durgut, Enes; Aldemir Dikici, BetülEmulsion templating is a method that enables the production of highly porous and interconnected polymer foams called polymerized high internal phase emulsions (PolyHIPEs). Since emulsions are inherently unstable systems, they can be stabilized either by surfactants or by particles (Pickering HIPEs). Surfactant-stabilized HIPEs form materials with an interconnected porous structure, while Pickering HIPEs typically form closed pore materials. In this study, we describe a system that uses submicrometer polymer particles to stabilize the emulsions. Polymers fabricated from these Pickering emulsions exhibit, unlike traditional Pickering emulsions, highly interconnected large pore structures, and we related these structures to arrested coalescence. We describe in detail the morphological properties of this system and their dependence on different production parameters. This production method might provide an interesting alternative to poly-surfactant-stabilized-HIPEs, in particular where the application necessitates large pore structures.Article Citation - WoS: 6Citation - Scopus: 6Tribocorrosion-Resistant Ti40nb-Tin Composites Havingtio(2)-Based Nanotubular Surfaces(American Chemical Society, 2022) Çaha, İhsan; Alves, Alexandra Cruz; Chirico, Caterina; Pinto, Ana Maria; Tsipas, Sophia; Gordo, Elena; Toptan, FatihA novel multifunctional material was developed byhard TiN particle reinforcement addition to a beta-type Ti40Nb alloy,followed by surface functionalization, yielding the formation of ananotubular layer. Corrosion and tribocorrosion behaviors wereinvestigated in a phosphate-buffered saline solution at bodytemperature. The results revealed that the Ti40Nb-TiNcomposites presented similaripassandE(i=0)values together withrelatively similarRoxandCox. However, its tribocorrosion resistancedrastically improved (wear volume is almost 15 times lower than anunreinforced alloy) as a consequence of the load-carrying effectgiven by the reinforcement phases. The corrosion and tribocorro-sion behaviors were further improved through surface functionaliza-tion as observed by significantly loweripassand higherRoxvalues andalmost undetectable wear volume loss from tribocorrosion tests dueto the formation of a well-adhered anatase-rutile TiO2-based nanotubular layer.Article Citation - WoS: 18Citation - Scopus: 22Effect of Fomes Fomentarius Cultivation Conditions on Its Adsorption Performance for Anionic and Cationic Dyes(American Chemical Society, 2022) Henning, Laura M.; Simon, Ulla; Abdullayev, Amanmyrat; Schmidt, Bertram; Pohl, Carsten; Nunez Guitar, Tamara; Ahmetoğlu, Çekdar Vakıf; Meyer, Vera; Bekheet, Maged F.; Gurlo, AleksanderLab-cultivated mycelia of Fomes fomentarius (FF), grown on a solid lignocellulose medium (FF-SM) and a liquid glucose medium (FF-LM), and naturally grown fruiting bodies (FF-FB) were studied as biosorbents for the removal of organic dyes methylene blue and Congo red (CR). Both the chemical and microstructural differences were revealed using X-ray photoelectron spectroscopy, Fourier-transform infrared spectroscopy, zeta potential analysis, and scanning electron microscopy, illuminating the superiority of FF-LM and FF-SM over FF-FB in dye adsorption. The adsorption process of CR on FF-LM and FF-SM is best described by the Redlich-Peterson model with β constants close to 1, that is, approaching the monolayer Langmuir model, which reach maximum adsorption capacities of 48.8 and 13.4 mg g-1, respectively, in neutral solutions. Adsorption kinetics follow the pseudo-second-order model where chemisorption is the rate-controlling step. While the desorption efficiencies were low, adsorption performances were preserved and even enhanced under simulated dye effluent conditions. The results suggest that F. fomentarius can be considered an attractive biosorbent in industrial wastewater treatment and that its cultivation conditions can be specifically tailored to tune its cell wall composition and adsorption performance.Article Citation - WoS: 8Citation - Scopus: 11Spreadability of Metal Powders for Laser-Powder Bed Fusion Via Simple Image Processing Steps(MDPI, 2022) Ahmetoğlu, Çekdar Vakıf; Hasdemir, Beyza; Biasetto, LisaThis paper investigates the spreadability of the spherical CoCrWMo powder for laser- powder bed fusion (PBF-LB) by using image processing algorithms coded in MATLAB. Besides, it also aims to examine the spreadability dependence with the other characteristics such as powder size distribution, apparent density, angle of repose. Powder blends in four different particle size distributions are prepared, characterized, and spreadability tests are performed with the PBF-LB. The results demonstrate that an increase in fine particle ratio by volume (below 10 µm) enhances the agglomeration and decreases the flowability, causing poor spreadability. These irregularities on the spread layers are quantified with simple illumination invariant analysis. A clear relation between powder spreadability and 3D printed structures properties in terms of residual porosity could not be defined since structural defects in 3D printed parts also depends on other processing parameters such as spatter formation or powder size over layer height ratio.Article Citation - WoS: 3Citation - Scopus: 5Physically Unclonable Security Patterns Created by Electrospinning, and Authenticated by Two-Step Validation Method(IOP Publishing, 2022) Taşcıoğlu, Didem; Atçı, Arda; Sevim Ünlütürk, Seçil; Özçelik, SerdarCounterfeiting is a growing economic and social problem. For anticounterfeiting, random and inimitable droplet/fiber patterns were created by the electrospinning method as security tags that are detectable under UV light but invisible in daylight. To check the authenticity of the original security patterns created; images were collected with a simple smartphone microscope and a database of the recorded original patterns was created. The originality of the random patterns was checked by comparing them with the patterns recorded in the database. In addition, the spectral signature of the patterns in the droplet/fiber network was obtained with a simple and hand-held spectrometer. Thus, by reading the spectral signature from the pattern, the spectral information of the photoluminescent nanoparticles was verified and thus a second-step verification was established. In this way, anticounterfeiting technology that combines ink formula, unclonable security pattern creation and two-level verification is developed.Article Citation - WoS: 9Citation - Scopus: 11Synthesis, Bottom Up Assembly and Thermoelectric Properties of Sb-Doped Pbs Nanocrystal Building Blocks(MDPI, 2021) Cadavid, Doris; Wei, Kaya; Liu, Yu; Zhang, Yu; Li, Mengyao; Genc, Aziz; Berestok, TaisiiaThe precise engineering of thermoelectric materials using nanocrystals as their building blocks has proven to be an excellent strategy to increase energy conversion efficiency. Here we present a synthetic route to produce Sb-doped PbS colloidal nanoparticles. These nanoparticles are then consolidated into nanocrystalline PbS:Sb using spark plasma sintering. We demonstrate that the introduction of Sb significantly influences the size, geometry, crystal lattice and especially the carrier concentration of PbS. The increase of charge carrier concentration achieved with the introduction of Sb translates into an increase of the electrical and thermal conductivities and a decrease of the Seebeck coefficient. Overall, PbS:Sb nanomaterial were characterized by two-fold higher thermoelectric figures of merit than undoped PbS.Article Citation - WoS: 2Citation - Scopus: 2Mn2+ Ions Incorporated Into Znsxse1-X Colloidal Quantum Dots: Controlling Size and Composition of Nanoalloys and Regulating Magnetic Dipolar Interactions(IOP Publishing, 2021) Ünlütürk, Seçil Sevim; Akdoğan, Yaşar; Özçelik, SerdarA facile synthesis method is introduced how to prepare magnetically active ultraviolet emitting manganese ions incorporated into ZnSxSe1-x colloidal quantum dot (nanoalloy) at 110 degrees C in aqueous solutions. The reaction time is the main factor to control the hydrodynamic size from 3 to 10 nm and the precursor ratio is significant to tune the alloy composition. ZnS shell layer on the ZnSxSe1-x core was grown to passivate environmental effects. The nanoalloy has ultraviolet emission at 380 nm having a lifetime of 80 ns and 7% quantum yield. The incorporation of Mn2+ ions into the nanoalloys induced magnetic activity but did not modify the structure and photophysical properties of the nanoalloys. Colloidal and powdery samples were prepared and analyzed by electron paramagnetic resonance (EPR) spectroscopy. In the colloidal dispersions, EPR spectra showed hyperfine line splitting regardless of the Mn2+ ion fractions, up to 6%, indicating that Mn2+ ions incorporated into the nanoalloys were isolated. EPR signals of the powdery samples were broadened when the fraction of Mn2+ ions was higher than 0.1%. The EPR spectra were simulated to reveal the locations and interactions of Mn2+ ions. The simulations suggest that the Mn2+ ions are located on the nanoalloy surfaces. These findings infer that the magnetic dipolar interactions are regulated by the initial mole ratio of Mn/Zn and the physical state of the nanoalloys adjusted by preparation methods.
- «
- 1 (current)
- 2
- 3
- »