Materials Science and Engineering / Malzeme Bilimi ve Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4719
Browse
24 results
Search Results
Now showing 1 - 10 of 24
Article Citation - WoS: 2Citation - Scopus: 5Experimental Modeling of Antimony Sulfides-Rich Geothermal Deposits and Their Solubility in the Presence of Polymeric Antiscalants(Elsevier, 2022) Karaburun, Emre; Sözen, Yiğit; Çiftçi, Celal; Şahin, Hasan; Baba, Alper; Akbey, Ümit; Yeşilnacar, Mehmet İrfan; Erdim, Eray; Regenspurg, Simona; Demir, Mustafa MuammerAntimony (Sb)-rich geothermal deposits have been observed in many geothermal power plants worldwide. They occur as red-colored, sulfidic precipitates disturbing energy-harvesting by clogging the geothermal installations. In order to prevent the formation of this scale, information on its physicochemical features is needed. For this purpose, Sb-rich sulfide-based deposits were synthesized at controlled conditions in a pressurized glass reactor at geothermal conditions (135 °C and 3.5 bar). Various polymeric antiscalants with different functional groups, such as acrylic acid, sulphonic acid, and phosphonic acid groups were tested for their effect on Sb sulfide solubility. An additional computational study was performed to determine the binding energy of Sb and S atoms to these groups. The results suggest that sulfonic acid groups are the most affective. Therefore, it was concluded that these macromolecule containing sulfonic acid groups and poly (vinyl sulfonic acid) derivatives could potentially act as antiscalants for the formation of antimony sulfide.Article Citation - WoS: 3Citation - Scopus: 3Green Fabrication of Lanthanide-Doped Hydroxide-Based Phosphors: Y(oh)(3):eu3+ Nanoparticles for White Light Generation(Beilstein-Institut Zur Forderung der Chemischen Wissenschaften, 2019) Güner, Tuğrul; Kuş, Anılcan; Özcan, Mehmet; Genç, Aziz; Şahin, Hasan; Demir, Mustafa MuammerPhosphors can serve as color conversion layers to generate white light with varying optical features, including color rendering index (CRI), high correlated color temperature (CCT), and luminous efficacy. However, they are typically produced under harsh synthesis conditions such as high temperature, high pressure, and/or by employing a large amount of solvent. In this work, a facile, water-based, rapid method has been proposed to fabricate lanthanide-doped hydroxide-based phosphors. In this sense, sub-micrometer-sized Y(OH)(3):Eu3+ particles (as red phosphor) were synthesized in water at ambient conditions in <= 60 min reaction time. The doping ratio was controlled from 2.5-20 mol %. Additionally, first principle calculations were performed on Y(OH)(3):Eu3+ to understand the preferable doping scenario and its optoelectronic properties. As an application, these fabricated red phosphors were integrated into a PDMS/YAG:Ce3+ composite and used to generate white light. The resulting white light showed a remarkable improvement (approximate to 24%) in terms of luminous efficiency, a slight reduction of CCT (from 3900 to 3600 K), and an unchanged CRI (approximate to 60) as the amount of Y(OH)(3):Eu3+ was increased.Article Citation - WoS: 3Citation - Scopus: 4Experimental and First-Principles Investigation of Cr-Driven Color Change in Cesium Lead Halide Perovskites(American Institute of Physics, 2019) Özen, Sercan; Güner, Tuğrul; Topçu, Gökhan; Özcan, Mehmet; Demir, Mustafa Muammer; Şahin, HasanHerein, we report room temperature Cr-doping for all-inorganic perovskites that have attracted great attention in recent years due to their extraordinary optical properties, low cost, and ease of synthesis. Incorporation of Cr 3 + ions into the perovskite crystal lattices is achieved by following a facile route involving an antisolvent recrystallization method at room temperature. It is shown that both Cr-doping and formation of crystals in the CsPbBr x Cl 3 - x phase are provided by increasing the concentration of the CrCl 3 solution. It is also observed that the doping procedure leads to the emergence of three types of distinctive peaks in the PL spectrum originating from CsPbBr x Cl 3 - x domains (476-427nm), Cr-strained host lattices (515nm), and midgap states formed by Cr dopants (675-775nm). It is also found that the Cr-doped perovskites emitting a dark violaceous color change their color to white with a high color rendering index (88) in 30-day time intervals. Easy-tunable optical properties of all-inorganic Cs perovskites indicate their great potential for future optoelectronic device applications.Article Citation - WoS: 4Citation - Scopus: 4Color-Tunable All-Inorganic Cspbbr3 Perovskites Nanoplatelet Films for Photovoltaic Devices(American Chemical Society, 2019) Özcan, Mehmet; Özen, Sercan; Topçu, Gökhan; Demir, Mustafa Muammer; Şahin, HasanHerein, we demonstrate a novel coating approach to fabricate CsPbBr3 perovskite nanoplatelet film with heat-free process via electrospraying from precursor solution. A detailed study is carried out to determine the effect of various parameters such as ligand concentration, electric field, flow rate, etc. on the optical properties. By controlling the volume ratios of the oleylamine (OAm) and oleic acid (OA), the coalescing and thickness of the resulting nanoplatelets can be readily tuned that results in control over emission in the range of 100 nm without any antisolvent crystallization or heating processes. The varying electrical field and flow rate was found as inefficient on the emission characteristics of the films. In addition, the crystal films were obtained under ambient conditions on the ITO coated glass surfaces as in the desired pattern. As a result, we demonstrated a facile and reproducible way of synthesizing and coating of CsPbBr3 perovskite nanoplatelets which is suitable for large-scale production. In this method, the ability of tuning the degree of quantum confinement for perovskite nanoplatelets is promising approach for the one-step fabrication of crystal films that may enable the use in optoelectronics.Article Citation - WoS: 89Citation - Scopus: 85Cspbbr3 Perovskites: Theoretical and Experimental Investigation on Water-Assisted Transition From Nanowire Formation To Degradation(American Physical Society, 2018) Akbalı, Barış; Topçu, Gökhan; Güner, Tuğrul; Özcan, Mehmet; Demir, Mustafa Muammer; Şahin, HasanRecent advances in colloidal synthesis methods have led to an increased research focus on halide perovskites. Due to the highly ionic crystal structure of perovskite materials, a stability issue pops up, especially against polar solvents such as water. In this study, we investigate water-driven structural evolution of CsPbBr3 by performing experiments and state-of-the-art first-principles calculations. It is seen that while an optical image shows the gradual degradation of the yellowish CsPbBr3 structure under daylight, UV illumination reveals that the degradation of crystals takes place in two steps: transition from a blue-emitting to green-emitting structure and and then a transition from a green-emitting phase to complete degradation. We found that as-synthesized CsPbBr3 nanowires (NWs) emit blue light under a 254 nm UV source. Before the degradation, first, CsPbBr3 NWs undergo a water-driven structural transition to form large bundles. It is also seen that formation of such bundles provides longer-term environmental stability. In addition theoretical calculations revealed the strength of the interaction of water molecules with ligands and surfaces of CsPbBr3 and provide an atomistic-level explanation to a transition from ligand-covered NWs to bundle formation. Further interaction of green-light-emitting bundles with water causes complete degradation of CsPbBr3 and the photoluminescence signal is entirely quenched. Moreover, Raman and x-ray-diffraction measurements revealed that completely degraded regions are decomposed to PbBr2 and CsBr precursors. We believe that the findings of this study may provide further insight into the degradation mechanism of CsPbBr3 perovskite by water.Article Citation - WoS: 15Citation - Scopus: 16Monitoring the Crystal Orientation of Black-Arsenic Via Vibrational Spectra(Royal Society of Chemistry, 2019) Kandemir, Ali; İyikanat, Fadıl; Şahin, HasanIn this study, the structural, mechanical, and vibrational properties of a recently discovered anisotropic ultra-thin material, black-arsenic (b-As), are investigated by using density functional theory. Direction dependent elastic constants such as in-plane stiffness, Young's modulus and Poisson's ratio of single-layer b-As are calculated and compared with those of the structural cousin black-phosphorus (b-P). The calculated Poisson's ratio of b-As for the zigzag direction is nearly 1, which is quite higher than that of b-P, 0.65. Besides, it is found that all the three elastic constants are highly anisotropic and their values in the zigzag direction are almost three times higher than that of the armchair direction. The mechanical strength of the material is also calculated and high-toughness is seen in both armchair and zigzag directions. It is revealed that the material is quite stiff against straining along the zigzag direction; in contrast, it is quite flexible along the armchair direction. Vibrational stability analysis shows that the material is stable up to 9% biaxially applied strain, and 12% and 45% uniaxially applied strain in the zigzag and armchair directions, respectively. Furthermore, the prominent Raman active peaks of the b-As structure show strong anisotropy in the strain dependent vibrational spectra and they can also be used for easy-determination of the crystal orientation of b-As from Raman measurements.Article Citation - WoS: 93Citation - Scopus: 95Single-Layer Janus-Type Platinum Dichalcogenides and Their Heterostructures(American Chemical Society, 2019) Kahraman, Zeynep; Kandemir, Ali; Yağmurcukardeş, Mehmet; Şahin, HasanUltrathin two-dimensional Janus-type platinum dichalcogenide crystals formed by two different atoms at opposite surfaces are investigated by performing state-of-the-art density functional theory calculations. First, it is shown that single-layer PtX2 structures (where X = S, Se, or Te) crystallize into the dynamically stable IT phase and are indirect band gap semiconductors. It is also found that the substitutional chalcogen doping in all PtX2 structures is favorable via replacement of surface atoms with a smaller chalcogen atom, and such a process leads to the formation of Janus-type platinum dichalcogenides (XPtY, where X and Y stand for S, Se, or Te) which are novel single-layer crystals. While all Janus structures are indirect band gap semiconductors as their binary analogues, their Raman spectra show distinctive features that stem from the broken out-of-plane symmetry. In addition, it is revealed that the construction of Janus crystals enhances the piezoelectric constants of PtX2 crystals significantly both in the in plane and in the out-of-plane directions. Moreover, it is shown that vertically stacked van der Waals heterostructures of binary and ternary (Janus) platinum dichalcogenides offer a wide range of electronic features by forming bilayer heterojunctions of type-I, type-II, and type-III, respectively. Our findings reveal that Janus-type ultrathin platinum dichalcogenide crystals are quite promising materials for optoelectronic device applications.Article Citation - WoS: 72Citation - Scopus: 77Gd3+-Doped Alpha-Cspbi3 Nanocrystals With Better Phase Stability and Optical Properties(American Chemical Society, 2019) Güvenç, Çetin Meriç; Yalçınkaya, Yenal; Özen, Sercan; Şahin, Hasan; Demir, Mustafa MuammerBlack alpha-CsPbI3 perovskites are unable to maintain their phase stability under room conditions; hence, the alpha-CsPbI3 phase transforms into a thermodynamically stable yellow delta-CsPbI3 phase within a few days, which has a nonperovskite structure and high band gap for optoelectronic applications. This phase transformation should be prevented or at least retarded to make use of superior properties of alpha-CsPbI3 in optoelectronic applications. In this study, Gd3+ doping was employed with the aim of increasing the stability of alpha-CsPbI3. All doped alpha-CsPbI3 nanocrystals with various levels of Gd3+, between 5 and 15 mol %, have shown greater phase stability than that of the pure alpha-CsPbI3 phase from 5 days up to 11 days under ambient conditions. This prolonged phase stability can be attributed to three potential reasons: increased tolerance factor of the perovskite structure, distorted cubic symmetry, and decreased defect density in nanocrystals. Urbach energy values suggest the reduction of defect density in the doped nanocrystals. Also, use of 10 mol % Gd3+ as a dopant material increases the photoluminescence quantum yield from 70 to 80% and fluorescence lifetime of alpha-CsPbI3 from 47.4 to 64.4 ns. Further, density functional theory calculations are in a good agreement with the experimental results.Article Citation - WoS: 10Citation - Scopus: 12The Effect of Dopa Hydroxyl Groups on Wet Adhesion To Polystyrene Surface: an Experimental and Theoretical Study(Elsevier, 2020) Yıldız, Remziye; Özen, Sercan; Şahin, Hasan; Akdoğan, YaşarMussels wet adhesive performance has been arousing curiosity for a long time. It is found that 3,4-dihydroxyphenylalanine (DOPA) is responsible for adhesive properties of mussels. Despite a large body of research characterizing the interactions DOPA with hydrophilic surfaces, relatively few works have addressed the mechanism of interactions with hydrophobic surfaces. The benzene ring of DOPA is the main attributor to the adhesion on hydrophobic polystyrene (PS) surface. However, here we showed that two hydroxyl groups of catechol have also effects on wet adhesion. We studied wet adhesive properties of DOPA, tyrosine and phenylalanine functionalized PEG polymers, PEG-(N-Boc-L-DOPA)(4), PEG-(N-Boc-L-Tyrosine)(4), PEG-(N-Boc-L-Phenylalanine)(4), on spin labeled PS nanobeads (SL-PS) by electron paramagnetic resonance (EPR) spectroscopy. Surface coverage ratio of SL-PS upon additions of PEG-(N-Boc-L-DOPA)(4), PEG-(N-Boc-L-Tyrosine)(4) and PEG-(N-Boc-L-Phenylalanine)(4) showed that SL-PS was covered with 70%, 50% and 0%, respectively. This showed that spontaneous wet adhesion on PS increases with the number of amino acids hydroxyl groups. This is also supported with the density functional theory (DFT) energy calculations and ab-initio molecular dynamics (AIMD) simulations. In water, interactions between water molecules and hydroxyl groups on the catechol induce catechol adhesion via 7C-7C stacking between the catechol and double styrene rings which were already tilted out with water.Article Citation - WoS: 13Citation - Scopus: 12Orthorhombic Cspbi3 Perovskites: Thickness-Dependent Structural, Optical and Vibrational Properties(Elsevier, 2020) Özen, Sercan; İyikanat, Fadıl; Özcan, Mehmet; Tekneci, Gülsüm Efsun; Eren, İsmail; Sözen, Yiğit; Şahin, HasanCesium lead halide perovskites have been subject to intense investigation, mostly because of their potential to be used in optoelectronic device applications. However, regarding the need for nanoscale materials in forthcoming nanotechnology applications, understanding of how the characteristic properties of these perovskite crystals are modified through dimensional crossover is essential. In this study, thickness-dependence of the structural, electronic and vibrational properties of orthorhombic CsPbI3, which is one of the most stable phase at room temperature, is investigated by means of state-of-the-art first-principles calculations. Our results show that (i) bilayers and monolayers of CsPbI3 can be stabilized in orthorhombic crystal symmetry, (ii) among; the possible ultra-thin perovskites only structures with CsI-terminated surface are dynamically stable (iii) electronic band gap increases with decrease in perovskite thickness due to quantum size effect and (iv) reflectivity and transmissivity of the orthorhombic CsPbI3 can be tuned by varying the thickness that modifies the electron confinement. (c) 2019 Elsevier B.V. All rights reserved.
- «
- 1 (current)
- 2
- 3
- »