GCRIS

Now showing 1 - 3 of 3

Effect of Colloidal Interactions in the Forming of Lead Magnesium Niobate Ceramics
(Izmir Institute of Technology, 2007) Deliormanlı, Aylin Müyesser; Polat, Mehmet
Electrokinetic properties of lead magnesium niobate (PMN) powders in liquid medium are investigated in this thesis. Isoelectric point of aqueous PMN suspensions was determined as a function of solids concentration. Dissolution character of both Pb+2 and Mg+2 cations in PMN structure were examined as a function of pH. Poly(acrylic acid)-poly(ethylene) oxide PAA/PEO comb polymers were tested as the novel dispersant in this system and their effect on the stability and flow behavior of aqueous PMN suspensions was investigated. Stability and flow behavior were mainly studied by rheological measurements and sedimentation experiments as a function of pH and polyelectrolyte concentration. Adsorption of comb polymers onto PMN surface and their effect on the powder dissolution were also investigated. Results indicated that the PAA/PEO comb polymers impart stability to PMN suspensions over a wide pH range and ionic strength where pure PAA fails. In the course of this study PMN powders were consolidated using two different wet shaping methods. First, PMN films were produced using aqueous tape casting method which is widely used in the manufacture of multilayer ceramic capacitors. Secondly, three-dimensional PMN lattices were produced using robocasting method. In the former case, the goal was to provide alternative recipes for the aqueous tape casting process to be utilized in industrial applications since the current technology is based on the organic solvent based techniques. Results showed that it was possible to produce high quality PMN films with thicknesses in the range of 10 to 250 .m using aqueous based tape casting process. In the latter case, the results showed that robocasting is a suitable technique for the preparation of three dimensional PMN ceramics. Based on these results overall conclusion and the contribution of this study can be summarized as follows: The work carried out gives new insights into the manufacturing of PMN based ceramics using aqueous based techniques. Such improvements may bring benefits in the manufacturing of smaller electronic components employed in the personal computers and mobile phones and other consumer products in the near future.
Gas Permeation Through Sol-Gel Derived Alumina and Silica Based Membranes
(Izmir Institute of Technology, 2009) Topuz, Berna; Çiftçioğlu, Muhsin
The scope of this thesis is to design defect-free microporous and mesoporous ceramic membranes having micro-engineered pore network that would contribute to the enhancement of pore control abilities as well as the thermal stability.In this study, mono-dispersed silica sols having well-defined silica spheres ranging in size from 5 to 700 nm were prepared through sol-gel methods and thin membrane layers were consolidated on either y-alumina support or unsupported form.The packing of 5 nm silica spheres resulted in micropores of 0.87 nm in 400 oC treatedmembranes with the porosity of 0.32 which are in well aggrement with the porosity level of random loose packing. Silica spheres with varying concentration and size were incorporated into polymeric network to complement the percolative structure of sphere packing with interpenetrated polymeric silica network in order to design well-defined thermally stable transport pathway. Low shrinkage value was obtained for sphere incorporated system providing the high thermal stability by affecting the thermally induced microcrack formation as well as the structural relaxation during consolidation.The resulting hybrid structure enabled the detailed transport properties that support to be able to control the pore structure but N2/CO2 separation properties are needed to be improved.Stable polymeric alumina sols having particle sizes smaller than 2 nm could be obtained when the hydrolysis conditions were accurately controlled. The mixture of prepared polymeric silica and alumina sols in mullite compositions (3:2) provided to the crystallization of mullite with homogeneously mixed stable oxide network upon heat treatment at 775 oC.
Investigation of Effects of Microstructural and Surface Properties of Ultrafiltration/ Nanofiltration Ceramic Membranes on Their Performance
(Izmir Institute of Technology, 2009) Erdem, İlker; Çiftçioğlu, Muhsin
The ceramic membranes with their superior chemical, thermal, mechanical and microbiological properties and long service lives are gaining importance in pressure driven filtration processes. The diverse requirements of different applications enforce preparation of tailor-made ceramic membranes with specific characteristics. This dissertation focused on the preparation and characterization and filtration performance of asymmetric multilayer ceramic membranes. Support is the layer responsible for mechanical stability while top layer is mainly responsible for separation and intermediate layer is balancing the microstructural difference between these two layers. The permeability of alumina support could be increased over 100 L / m2 h by 15% starch addition. The intermediate layer was prepared by coating fine alumina or zirconia powders and / or colloidal sols with thicknesses between 0.2-70 .. The top layer was formed from pure or mix of zirconia or titania polymeric sols with average particle sizes in the range of 3 . 50 nm with a thickness smaller than 1.. The physicochemical properties of these mixed oxides were modified by changing the composition and calcination temperature enabling preparation of top layers with varying Donnan exclusion capacities. The membranes prepared could reject sugar, PEG 1000 and PEG 4000 up to 10, 60 and 19%, respectively, that which can be increased via further optimization of parameters in coating / heat treatment processes.

Phd Degree / Doktora

Browse

Filters

Settings

Sort By

Results per page

Search Results