Phd Degree / Doktora

Now showing 1 - 2 of 2

The Penetration Behavior of Repeated Hemisphere Core Sandwich Structures: an Experimental and Numerical Study
(Izmir Institute of Technology, 2018) Turan, Ali Kıvanç; Taşdemirci, Alper; Güden, Mustafa
In this study, penetration behavior of novel core structure consisting hemispherical and cylindrical parts was investigated. Core units were manufactured with deep drawing method in two thicknesses to have monolithic form without any sort of assembly method or element. Produced specimens were then subjected to penetration tests at low and intermediate velocities against blunt, conical and hemispherical tipped indenters using special fixtures and apparatuses on conventional testing equipment. Effect of heat treatment on penetration behavior was investigated to observe whether residual stresses arise from manufacturing process changes the penetration behavior. Confinement effects were studied experimentally with a special fixture, allowing tested specimen to be radially confined with other core units as in an armor structure. Finally, experimental work was finished by conducting a case study where core units were subjected to spherical projectile impact up to impact velocities of 180 m.s-1 in a composite sandwich structure. Results show that each indenter geometry showed unique deformation characteristics in testing of both core units and both of the core geometries were able to hold a steel spherical projectile with mass of 110 g without full perforation at impact velocity of 180 m.s-1. Details of experimental results were presented in each chapter. Study also included modeling parts where core units were numerically produced with residual stresses and strains and good correlation was noted where thickness was compared with actual measurements on core units. Test conducted on single core structure in as-received and heat-treated condition were also repeated in numerical environment, where numerical study exhibited good correlation on both forcedisplacement curves and deformation of core units with tests. Correlation achieved with experimental study has led into further investigations of strain rate and micro-inertia where behavior of core units was studied at numerical impact velocities of 300 m.s-1. Results show that both strain rate and micro-inertia increase the local maximums and average of force levels. Effect of strain rate and micro-inertia is clearly distinguished for a threshold displacement level where micro-inertia is further dominant on behavior.
Experimental and Numerical Evaluation of the Blast-Like Loading of Fiber Reinforced Polymer Composites and Aluminum Corrugated Core Composite Sandwiches Through Projectile Impact Testing Using Aluminum Corrugated Projectiles
(Izmir Institute of Technology, 2015) Odacı, İsmet Kutlay; Güden, Mustafa; Taşdemirci, Alper
This thesis develops and validates a laboratory scale blast-like testing method that can simulate explosive blast tests in air and under water without using explosives. The study has mainly focused on the shock loading potential of 1050 H14 trapezoidal corrugated core aluminium sandwich structures on E-glass/polyester composite plates and corrugated core composite sandwich structures experimentally, numerically and analytically. The composite plates were modelled using MAT_162 material model in LS-DYNA finite element code. Quasi-static and high strain rate tests were performed to determine the material model parameters of composite and corrugated structure. The resultant parameters were calibrated and validated by comparing the numerical results with the experimental results. The planar shock wave formation and propagation in corrugated core sandwich structures were shown experimentally using a direct impact Split Hopkinson Pressure Bar test set-up. Rigid-perfectly-plastic-locking material model and Hugoniot jump relations revealed the shock loading potential of the tested corrugated core sandwich structures. The shock loading response of composite plates and sandwich structures were investigated by firing the corrugated sandwich projectiles on the targets. These impact tests were also simulated numerically and an analytic model was used to predict the plate deflections. The experimentally, numerically and analytically determined back face deflections were compared with the deflections of the Conwep blast simulations in LS-DYNA. The results have shown that the corrugated core sandwich structures can generate shock loading as in the explosive blast tests and can be used to produce shock loads in laboratory scale experiments.

Phd Degree / Doktora

Browse

Filters

Settings

Sort By

Results per page

Search Results