Energy Systems Engineering / Enerji Sistemleri Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4752
Browse
6 results
Search Results
Article Citation - WoS: 5Citation - Scopus: 5Exergetic Assessment of an Solar Powered Stand-Alone System Using Liquid Organic Hydrogen Carrier for Energy Storage(Elsevier, 2023) Palmero-Marrero, Ana I.; Zairov, Rüstem; Borge-Diez, David; Çağlar, Başar; Açıkkalp, Emin; Altuntaş, ÖnderThe integration of energy storage technologies into renewable energy systems has gained increasing attention for continuous supply of the renewable-based enegy. Among different storage alternatives, the use of a Liquid Organic Hydrogen Carrier (LOHC) has a significant potential as a reversible energy carrier for short and longterm energy storage. In this study, the technical and economic performance of an stand-alone renewable energy systems using a LOHC for energy storage have been evaluated by exergy-based methods in addition to simple energy and economic analysis. The analysis of the LOHC-free system was also included to determine the effect of LOHC on the system performance. The system containing phovoltaic (PV) panels, an electrolyzer, a micro gas turbine and hydrogenation/dehydrogenation LOHC units was designed to meet the power, heating and cooling requirement of a residential building. The system modelling and performance evaluation were made by using TRNSYS and EES softwares. Results show that the LOHC-containing system has higher energy and exergy efficiencies and exergoeconomic performance than the LOHC-free system while the latter is economically more feasible than the former due to its low capital investment cost.Review Citation - WoS: 21Citation - Scopus: 23A Comprehensive Review of Computational Fluid Dynamics Simulation Studies in Phase Change Materials: Applications, Materials, and Geometries(Springer, 2023) Soodmand, A. Mohammadian; Azimi, B.; Nejatbakhsh, S.; Pourpasha, H.; Farshchi, M. Ebrahimi; Aghdasinia, H.; Mohammadpourfard, Mousa; Heris, S. ZeinaliThermal energy storage systems (TESS) have emerged as significant global concerns in the design and optimization of devices and processes aimed at maximizing energy utilization, minimizing energy loss, and reducing dependence on fossil fuel energy for both environmental and economic reasons. Phase change materials (PCMs) are widely recognized as promising candidates due to their high latent heat storage (LHS) capacity. This review thoroughly evaluates the computational fluid dynamics (CFD) studies conducted in various sections, encompassing materials, modeling, simulation, as well as the results, advantages, and disadvantages of these works. The study is organized into three distinct sections. The first section discusses the applications of PCMs in various areas, including lithium-ion batteries, solar applications, building applications, electronics, and heating and cooling systems. The second section provides a comprehensive summary of cylindrical, rectangular, spherical, arbitrary shapes, and packed-bed geometries employed in TESS. The third section investigates the different types of materials used as PCMs. Based on the findings of this study, it can be concluded that industrial applications of hybrid nanocomposites incorporating PCMs in different geometries pose challenges, particularly in three-dimensional (3D) settings, where instability becomes a significant concern. Hence, further research and investigation are necessary to address these challenges adequately. In conclusion, this study serves as a reference review for future research endeavors in the field of simulating various PCMs in different geometries and applications. It provides valuable insights into the current state of knowledge, highlights potential areas for improvement, and offers guidance for advancing simulation techniques related to PCMs.Article Citation - WoS: 103Citation - Scopus: 113Preparation and Characterizations of Tio2/Zno Nanohybrid and Its Application in Photocatalytic Degradation of Tetracycline in Wastewater(Elsevier, 2023) Zeinali Heris, Saeed; Etemadi, Martin; Mousavi, Seyed Borhan; Mohammadpourfard, Mousa; Ramavandi, BahmanThe photodegradation of tetracycline antibiotics (TC) in an aqueous solution, using the TiO2 nanoparticles, ZnO microparticles, and TiO2/ZnO composite under the UV lamp in a continuous reactor, was performed. The effects of different parameters, such as the initial TC concentration, medium pH, ratio of each photocatalyst, and the flow rate were comprehensively studied. SEM, EDX, and XRD characterization techniques were employed to study the morphology and structure features of the prepared composite. The results revealed that a more significant amount of TC is not easily removed from wastewater. Furthermore, by increasing the pH of the medium to 11, the efficiency of TC degradation was increased, while the amount of removal remained stable at higher pH values. As the flow rate increased up to 190 mL/min, the removal efficiency increased; however, at higher flow rates, lower efficiency was obtained. Moreover, using multivariate analysis and response surface methodology (RSM), a model for removing TC and the effect of experimental parameters on removal efficiency was proposed. The optimal conditions using the RSM method were found to be the reduction efficiency of 78.94 % in pH = 11 (flow rate of 132 mL/min, and TiO2 concentration of 323 mg) and reduction efficiency of 75.89% in pH = 9 (flow rate of 143.19 mL/min and TiO2 concentration of 312.73 mg). © 2023 Elsevier B.V.Article Citation - WoS: 7Citation - Scopus: 7Comprehensive Thermoeconomic Study of a New Solar Thermosyphon-Assisted Multigeneration System(Elsevier, 2023) Anamaq, Rasoul Najafi; Khani, Leyla; Mohammadpourfard, Mousa; Heris, Saeed Zeinali; Gökçen Akkurt, GüldenNowadays, due to the global energy crisis, limited reservoirs of fossil fuels, and their negative environmental effects, the use of renewable energy sources and multigeneration systems have become good alternatives for conventional thermodynamic systems. One of these resources, whose technology has developed rapidly in recent years, is the use of solar energy for the simultaneous generation of various products. Therefore, in this research, a multigeneration system with several subsystems is introduced. The proposed system includes a solar energy collector to receive thermal energy, two thermal energy storage tanks, an organic Rankine cycle, and a Kalina cycle to generate electricity, a multi-effect distillation unit to produce fresh water, an electrolyzer to produce hydrogen, as well as heat recovery for hot water and hot air generation. In this multigeneration system, the cooling unit is designed with the help of a thermosyphon. The performance of the proposed system is studied from energy, exergy, environmental, and exergoeconomic viewpoints using Aspen HYSYS and EES software. The obtained results show that due to the addition of the thermosyphon unit to the refrigeration system, the exergy efficiency increases from 55.62% to 70.26%. As a result of this combination, the performance of the whole system is improved and the amount of costs are reduced. In addition, the parabolic collector system has the highest exergy destruction ratio, 39%, among the subsystems. Furthermore, the results of the exergoeconomic analysis indicate that the PEM water heater with 33.3% and the ejector with 22.7% own the highest cost destruction rates.Article Citation - WoS: 8Citation - Scopus: 10Spray Analysis of Biodiesels Derived From Various Biomass Resources in a Constant Volume Spray Chamber(American Chemical Society, 2022) Ulu, Anılcan; Yıldız, Güray; Rodriguez, Alvaro Diez; Özkol, ÜnverThis research aimed to analyze the spray characteristics of various biodiesels, which have rarely been investigated in terms of spray analysis in the literature compared to fossil diesel. For this purpose, four different methyl ester-type biodiesels were produced from canola, corn, cottonseed, and sunflower oils. These feedstocks were selected due to their wide availability in Turkey and being among the significant resources for biodiesel production. Measured physical properties of biodiesel samples showed that biodiesel fuels had, on average, 1.7 to 1.9 times higher viscosities, 5.3 to 6.6% larger densities, and 37 to 39.1% higher contact angle values than the reference diesel fuel. Spray characteristics of all fuels were experimentally examined in a constant volume spray chamber under chamber pressures of 0, 5, 10, and 15 bar and injection pressures of 600, 800, and 1000 bar. All tested biodiesels performed, on average, 3 to 20% longer spray penetration lengths, 5 to 30% narrower spray cone angles, and 5-18% lesser spray areas than the reference diesel fuel under chamber pressures of 5 and 10 bar. No significant differences occurred at 15 bar ambient pressure between biodiesels and diesel. In addition, analytical and empirical predictions showed that biodiesels had around 21.2-35.1% larger SMD values and approximately 7% lower air entrainment.Article Citation - WoS: 67Citation - Scopus: 74Suitable Site Selection for Offshore Wind Farms in Turkey’s Seas: Gis-Mcdm Based Approach(Springer, 2021) Genç, Mustafa Serdar; Karipoğlu, Fatih; Koca, Kemal; Azgın, Şükrü TanerOffshore wind energy resources are not fully exploited renewable energy resources until now and could play a crucial role in mitigating the impacts of climate change by the generation of renewable electricity. Planning processes such as technical, social, environmental, various agents, and political concerns are necessary for the development of offshore wind energy projects. The objective of this study was to assess the comprehensive feasibility of a desired offshore wind power plant applying Geographical Information Systems (GIS) and Multi-Criteria Decision-Making (MCDM) guidance for the coastal area of Turkey. Furthermore, EMODnet (the European Marine Observation and Data Network) was employed for data acquisition to unlock fragmented and hidden marine data resources and to facilitate investment in sustainable coastal and offshore activities. For the determination of potential site with Multi-Criteria Decision Maker Method, 3 main criteria Technical (C1), Environmental (C2), and Social (C3), and 13 sub-criteria were determined. Based on these criteria, the suitability map was created by using all criteria map layers with their buffer zones. The final map indicated that %1.38 (3294.8 km(2)) of Turkey Seas was suitable for offshore wind farms. The most suitable region was determined in the Marmara Sea with 1194 km(2). The Aegean Sea, the Black Sea, and the Mediterranean Sea were following the Marmara Sea in terms of the huge suitable regions respectively. It was apparent that the growth of offshore wind farms in Turkey would increase if the supporting mechanism and the necessary legislation were ensured.