Sürdürülebilir Yeşil Kampüs Koleksiyonu / Sustainable Green Campus Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7755
Browse
33 results
Search Results
Article Citation - WoS: 15Citation - Scopus: 19Brominated Flame Retardants in a Computer Technical Service: Indoor Air Gas Phase, Submicron (pm1) and Coarse (pm10) Particles, Associated Inhalation Exposure, and Settled Dust(Elsevier Ltd., 2019) Genişoğlu, Mesut; Sofuoğlu, Aysun; Kurt Karakuş, Perihan Binnur; Birgül, Aşkın; Sofuoğlu, Sait CemilBrominated flame retardants (BFRs) are found in multi-media indoors, therefore, may pose serious risks to human health. This study investigated the occurrence of BFRs in particulate matter (PM1 and PM10) and gas phase by active and passive sampling, and settled dust to estimate potential exposure in a computer technical service. Polybrominated diphenyl ethers (PBDEs) and their alternatives (novel BFRs, NBFRs) were studied. PM and gas phase were collected on glass fiber filters and polyurethane foam plugs, respectively, and analyzed with a GC/MS after extraction, clean-up, and concentration. Inhalation exposure of the staff was estimated based on the measured concentrations using Monte Carlo simulation. BDE-209 was the dominating PBDE congener in all media while bis(2-ethylhexyl)-3,4,5,6-tetrabromophthalate and 1,2-bis(2,4,6-tribromophenoxy)ethane were those of NBFRs. Submicron particulate matter (PM1) BFR levels constituted about one half of the PM10-associated concentrations, while average PM10 mass concentration (69.9 μg m−3) was nine times that of PM1 (7.73 μg m−3). Calculated log10 dust-gas and PM-gas partitioning coefficients ranged from −5.03 to −2.10, −2.21 to −0.55, and −2.26 to −1.04 for settled dust, PM10, and PM1, respectively. The indoor/outdoor concentration ratios were >1 for all compounds indicating the strength of indoor sources in the service. The estimated potential inhalation exposures, for future chronic-toxic and carcinogenic risk assessments, indicated that the levels of gas-phase and PM1-associated exposures were similar at approximately one half of PM10-associated levels. Results of this study indicate that the occurrence of BFRs in all studied media should be taken into consideration for occupational health mitigation efforts.Article Citation - WoS: 27Citation - Scopus: 28Fast Formation of Nitro-Pahs in the Marine Atmosphere Constrained in a Regional-Scale Lagrangian Field Experiment(American Chemical Society, 2019) Mulder, Marie D.; Dumanoğlu, Yetkin; Efstathiou, Christos; Kukucka, Petr; Matejovicova, Jana; Maurer, Christian; Pribylova, Petra; Prokes, Roman; Sofuoğlu, Aysun; Sofuoğlu, Sait Cemil; Wilson, Jake; Zetzsch, Cornelius; Wotawa, Gerhard; Lammel, GerhardPolycyclic aromatic hydrocarbons (PAHs) and some of their nitrated derivatives, NPAHs, are seemingly ubiquitous in the atmospheric environment. Atmospheric lifetimes may nevertheless vary within a wide range, and be as short as a few hours. The sources and sinks of NPAH in the atmosphere are not well understood. With a Lagrangian field experiment and modeling, we studied the conversion of the semivolatile PAHs fluoranthene and pyrene into the 2-nitro derivatives 2-nitrofluoranthene and 2-nitropyrene in a cloud-free marine atmosphere on the time scale of hours to 1 day between a coastal and an island site. Chemistry and transport during several episodes was simulated by a Lagrangian box model i.e., a box model coupled to a Lagrangian particle dispersion model, FLEXPART-WRF. It is found that the chemical kinetic data do capture photochemical degradation of the 4-ring PAHs under ambient conditions on the time scale of hours to 1 day, while the production of the corresponding NPAH, which sustained 2-nitrofluoranthene/fluoranthene and 2-nitropyrene/pyrene yields of (3.7 ± 0.2) and (1.5 ± 0.1)%, respectively, is by far underestimated. Predicted levels of NPAH come close to observed ones, when kinetic data describing the reactivity of the OH-adduct were explored by means of theoretically based estimates. Predictions are also underestimated by 1-2 orders of magnitude, when NPAH/PAH yields reported from laboratory experiments conducted under high NOx conditions are adopted for the simulations. It is concluded that NPAH sources effective under low NOx conditions, are largely underestimated.Article Citation - WoS: 34Citation - Scopus: 35Development of High Flux Nanofiltration Membranes Through Single Bilayer Polyethyleneimine/Alginate Deposition(Elsevier Ltd., 2019) Tekinalp, Önder; Alsoy Altınkaya, SacideThe aim of this study is to prepare high flux, stable, antifouling nanofiltration membranes through single bilayer polyelectrolyte deposition. To this end, a tight ultrafiltration support membrane was prepared from a polysulfone/sulfonated polyethersulfone blend. Deposition of a polyethyleneimine and alginate pair on this support has reduced the molecular weight cut off from 6 kDa to below 1 kDa. The pure water permeability and polyethylene glycol 1000 rejection of the coated membrane were found to be 15.5 ± 0.3 L/m2·h·bar and 90 ± 0.6%, respectively, by setting the deposition pH for each layer to 8 and the ionic strengths to 0.5 M and 0 M. This membrane has exhibited significantly higher permeability than commercial membranes with the same molecular weight cut off, retaining 98% of the initial flux during 15 h filtration of bovine serum albumine. In addition, the membrane has been able to completely remove anionic dyes from aqueous solution by showing 99.9% retentions to Reactive red 141, Brilliant blue G and Congo red with a 2 bar transmembrane pressure. High flux and membrane stability in acidic and salty environments have been achieved when deposition conditions favor high adsorption levels for the first layer and strong ionic cross-linking between the carboxyl group on the alginate and the amine groups on the polyethyleneimineArticle Citation - WoS: 27Citation - Scopus: 34Chitosan/Montmorillonite Composite Nanospheres for Sustained Antibiotic Delivery at Post-Implantation Bone Infection Treatment(IOP Publishing Ltd., 2019) Kımna, Ceren; Değer, Sibel; Tamburacı, Sedef; Tıhmınlıoğlu, FundaDespite the advancements in bone transplantation operations, inflammation is still a serious problem that threatens human health at the post-implantation period. Conventional antibiotic therapy methods may lead to some side effects such as ototoxicity and nephrotoxicity, especially when applied in high doses. Therefore, local drug delivery systems play a vital role in bone disorders due to the elimination of the disadvantages introduced by conventional methods. In the presented study, it was aimed to develop Vancomycin (VC) and Gentamicin (GC) loaded chitosan-montmorillonite nanoclay composites (CS/MMT) to provide required antibiotic doses to combat post-implantation infection. CS/MMT nanocomposite formation was supplied by microfluidizer homogenization and spherical drug carrier nanoparticles were obtained by electrospraying technique. Three factors; voltage, distance and flowrate were varied to fabricate spherical nanoparticles with uniform size. Emprical model was developed to predict nanosphere size by altering process variables. Nanospheres were characterized in terms of morphology, hydrodynamic size, zeta potential, drug encapsulation efficiency and release profile. Drug loaded nanospheres have been successfully produced with a size range of 180-350 nm. Nanocomposite drug carriers showed high encapsulation efficiency (80%-95%) and prolonged release period when compared to bare chitosan nanospheres. The drug release from nanocomposite carriers was monitored by diffusion mechanism up to 30 d. The in vitro release medium of nanospheres showed strong antimicrobial activity against gram-positive S. aureus and gram-negative E. coli bacteria. Furthermore, it was found that the nanospheres did not show any cytotoxic effect to fibroblast (NIH/3T3) and osteoblast (SaOS-2) cell lines. The results demonstrated that the prepared composite nanospheres can be a promising option for bone infection prevention at the post implantation period.Article Citation - WoS: 19Citation - Scopus: 29Modeling of an Activated Sludge Process for Effluent Prediction—a Comparative Study Using Anfis and Glm Regression(Springer Verlag, 2018) Araromi, Dauda Olurotimi; Majekodunmi, Olukayode Titus; Adeniran, Jamiu Adetayo; Salawudeen, Taofeeq OlalekanIn this paper, nonlinear system identification of the activated sludge process in an industrial wastewater treatment plant was completed using adaptive neuro-fuzzy inference system (ANFIS) and generalized linear model (GLM) regression. Predictive models of the effluent chemical and 5-day biochemical oxygen demands were developed from measured past inputs and outputs. From a set of candidates, least absolute shrinkage and selection operator (LASSO), and a fuzzy brute-force search were utilized in selecting the best combination of regressors for the GLMs and ANFIS models respectively. Root mean square error (RMSE) and Pearson’s correlation coefficient (R-value) served as metrics in assessing the predicting performance of the models. Contrasted with the GLM predictions, the obtained modeling results show that the ANFIS models provide better predictions of the studied effluent variables. The results of the empirical search for the dominant regressors indicate the models have an enormous potential in the estimation of the time lag before a desired effluent quality can be realized, and preempting process disturbances. Hence, the models can be used in developing a software tool that will facilitate the effective management of the treatment operation.Article Citation - WoS: 91Citation - Scopus: 95Source Apportionment and Carcinogenic Risk Assessment of Passive Air Sampler-Derived Pahs and Pcbs in a Heavily Industrialized Region(Elsevier Ltd., 2018) Çetin, Banu; Yurdakul, Sema; Güngörmüş, Elif; Öztürk, Fatma; Sofuoğlu, Sait CemilCancer has become the primary reason of deaths in Dilovasi probably due to its location with unique topography under the influence of heavy industrialization and traffic. In this study, possible sources and carcinogenic health risks of PAHs and PCBs were investigated in Dilovasi region by Positive Matrix Factorization (PMF) and the USEPA approach, respectively. PAHs and PCBs were measured monthly for a whole year at 23 sampling sites using PUF disk passive samplers. Average ambient air concentrations were found as 285 ± 431 ng/m 3 and 4152 ± 6072 pg/m 3 , for Σ 15 PAH and Σ 41 PCB, respectively. PAH concentrations increased with decreasing temperature especially at urban sites, indicating the impact of residential heating in addition to industrial activities and traffic. On the other hand, PCB concentrations mostly increased with temperature probably due to enhanced volatilization from their sources. Possible sources of PAHs were found as emissions of diesel and gasoline vehicles, biomass and coal combustion, iron and steel industry, and unburned petroleum/petroleum products, whereas iron-steel production, coal and biomass burning, technical PCB mixtures, and industrial emissions were identified for PCBs. The mean carcinogenic risk associated with inhalation exposure to PAHs and PCBs were estimated to be >10 −6 and >10 −5 , respectively, at all sampling points, while the 95th percentile was >10 −5 at 15 of 23 and >10 −4 at 8 of 23 sampling locations, respectively. Probabilistic assessment showed, especially for PCBs, that a majority of Dilovasi population face significant health risks. The higher risks due to PCBs further indicated that PCBs and possibly other pollutants originating from the same sources such as PBDEs and PCNs may be an important issue for the region.Article Citation - WoS: 32Citation - Scopus: 37Mcdm Analysis of Wind Energy in Turkey: Decision Making Based on Environmental Impact(Springer Verlag, 2018) Değirmenci, Sinem; Bingöl, Ferhat; Sofuoğlu, Sait CemilDevelopment of new wind energy projects require complex planning process involving many social, technical, economic, environmental, political concerns, and different agents such as investors, utilities, governmental agencies, or social groups. The aim of this study is to develop a tool combining Geographic Information System (GIS) and Multi-Criteria Decision-Making (MCDM) methodologies, and its application for Turkey as a case study. A variety of constraints and criteria were identified based on a literature review and regulations gathered from variety of agencies, use of which resulted in determination of infeasible sites. Then, pairwise comparisons were carried out using analytic hierarchy process as the MCDM method to estimate relative importance of the criteria, and to visualize a suitability map with three classes. As the final stage, decision making was carried out based on environmental impact where 45.5% of the Turkish territory was found as infeasible area. Sixty percent of the remaining area are covered by the moderate suitability class, followed by the highly suitable area (20.3%) and low suitable area (19.8%). The output of this study can be used by energy planners to estimate the extent that wind energy can be developed based on public perception, administrative, and environmental aspectsArticle Citation - WoS: 98Citation - Scopus: 118Organophosphate Ester (opes) Flame Retardants and Plasticizers in Air and Soil From a Highly Industrialized City in Turkey(Elsevier Ltd., 2018) Kurt Karakuş, Perihan Binnur; Alegria, Henry; Birgül, Aşkın; Güngörmüş, Elif; Jantunen, LiisaPassive air samples were collected at eight sites in Bursa, Turkey during five sampling periods between February–December 2014. Locations encompassed urban, suburban, industrial, rural and background environments. Soil samples (n = 8) were collected at each site during February 2014. Six OPEs were detected in samples: tris(2-chloroethyl) phosphate (TCEP), tris(chloropropyl) phosphate (TCPP), triphenyl phosphate (TPHP), tris(2-butoxyethyl) phosphate (TBOEP), tris(2-ethylhexyl) phosphate (TEHP), and tris(2-isopropylphenyl) phosphate (T2iPPP). Frequency of detection in air samples was TCPP and TPHP (100%) > TBOEP (88%) > TCEP (85%) > TEHP (78%) > T2iPPP (20%). Total OPEs in air per site by sampling period (excluding non-detects) ranged from 529 to 19,139 pg/m3. In soil, total OPEs ranged from 38 to 468 ng/g dw. In air, alkylated OPEs dominated followed by halogenated and aryl OPEs. In air, annual mean concentrations were TBOEP > TCPP > TPHP > T2iPPP > TEHP > TCEP. In soils, alkylated OPEs were dominant at six sites and chlorinated OPEs at two sites. A comparison of OPE profiles between air and soil suggests that soils may be partly a source of OPEs to air. Mean concentrations in air were not directly proportional to temperature, and there were differences between alkylated compared to halogenated and aryl OPEs. In air, total and alkylated OPEs levels were fairly uniform, whereas more variability was found for the halogenated and aryl compounds. The relative contribution to total OPEs decreases for alkylated OPEs and increases for halogenated OPEs in samples going from background to suburban to urban and industrial sites. Levels of individual OPEs were all positively correlated between air and soils. In air, correlations between individual compounds were weak to moderate and were only statistically significant for TBOEP and TPHP. In soils, correlations were generally stronger and statistically significant only for TPHP and T2iPPP.Article Citation - WoS: 18Citation - Scopus: 21Polybrominated Diphenyl Ethers (pbdes) in Background Air Around the Aegean: Implications for Phase Partitioning and Size Distribution(Springer Verlag, 2017) Besis, Athanasios; Lammel, Gerhard; Kukucka, Petr; Samara, Constantini; Sofuoğlu, Aysun; Dumanoğlu, Yetkin; Eleftheriadis, Kostas; Kouvarakis, Giorgos; Sofuoğlu, Sait Cemil; Vassilatou, Vassiliki; Voutsa, DimitraThe occurrence and atmospheric behavior of tri- to deca-polybrominated diphenyl ethers (PBDEs) were investigated during a 2-week campaign concurrently conducted in July 2012 at four background sites around the Aegean Sea. The study focused on the gas/particle (G/P) partitioning at three sites (Ag. Paraskevi/central Greece/suburban, Finokalia/southern Greece/remote coastal, and Urla/Turkey/rural coastal) and on the size distribution at two sites (Neochorouda/northern Greece/rural inland and Finokalia/southern Greece/remote coastal). The lowest mean total (G + P) concentrations of ∑7PBDE (BDE-28, BDE-47, BDE-66, BDE-99, BDE-100, BDE-153, BDE-154) and BDE-209 (0.81 and 0.95 pg m−3, respectively) were found at the remote site Finokalia. Partitioning coefficients, KP, were calculated, and their linear relationships with ambient temperature and the physicochemical properties of the analyzed PBDE congeners, i.e., the subcooled liquid pressure (PL°) and the octanol-air partition coefficient (KOA), were investigated. The equilibrium adsorption (PL°-based) and absorption (KOA-based) models, as well as a steady-state absorption model including an equilibrium and a non-equilibrium term, both being functions of log KOA, were used to predict the fraction Φ of PBDEs associated with the particle phase. The steady-state model proved to be superior to predict G/P partitioning of BDE-209. The distribution of particle-bound PBDEs across size fractions < 0.95, 0.95–1.5, 1.5–3.0, 3.0–7.2, and > 7.2 μm indicated a positive correlation between the mass median aerodynamic diameter and log PL° for the less brominated congeners, whereas a negative correlation was observed for the high brominated congeners. The potential source regions of PBDEs were acknowledged as a combination of long-range transport with short-distance sources.Article Citation - WoS: 40Citation - Scopus: 47Gelatin-Based 3d Conduits for Transdifferentiation of Mesenchymal Stem Cells Into Schwann Cell-Like Phenotypes(Elsevier Ltd., 2017) Uz, Metin; Büyüköz, Melda; Sharma, Anup D.; Sakaguchi, Donald S.; Alsoy Altınkaya, Sacide; Mallapragada, Surya K.In this study, gelatin-based 3D conduits with three different microstructures (nanofibrous, macroporous and ladder-like) were fabricated for the first time via combined molding and thermally induced phase separation (TIPS) technique for peripheral nerve regeneration. The effects of conduit microstructure and mechanical properties on the transdifferentiation of bone marrow-derived mesenchymal stem cells (MSCs) into Schwann cell (SC) like phenotypes were examined to help facilitate neuroregeneration and understand material-cell interfaces. Results indicated that 3D macroporous and ladder-like structures enhanced MSC attachment, proliferation and spreading, creating interconnected cellular networks with large numbers of viable cells compared to nanofibrous and 2D-tissue culture plate counterparts. 3D-ladder-like conduit structure with complex modulus of ∼0.4 × 106 Pa and pore size of ∼150 μm provided the most favorable microenvironment for MSC transdifferentiation leading to ∼85% immunolabeling of all SC markers. On the other hand, the macroporous conduits with complex modulus of ∼4 × 106 Pa and pore size of ∼100 μm showed slightly lower (∼65% for p75, ∼75% for S100 and ∼85% for S100β markers) immunolabeling. Transdifferentiated MSCs within 3D-ladder-like conduits secreted significant amounts (∼2.5 pg/mL NGF and ∼0.7 pg/mL GDNF per cell) of neurotrophic factors, while MSCs in macroporous conduits released slightly lower (∼1.5 pg/mL NGF and 0.7 pg/mL GDNF per cell) levels. PC12 cells displayed enhanced neurite outgrowth in media conditioned by conduits with transdifferentiated MSCs. Overall, conduits with macroporous and ladder-like 3D structures are promising platforms in transdifferentiation of MSCs for neuroregeneration and should be further tested in vivo. Statement of Significance This manuscript focuses on the effect of microstructure and mechanical properties of gelatin-based 3D conduits on the transdifferentiation of mesenchymal stem cells to Schwann cell-like phenotypes. This work builds on our recently accepted manuscript in Acta Biomaterialia focused on multifunctional 2D films, and focuses on 3D microstructured conduits designed to overcome limitations of current strategies to facilitate peripheral nerve regeneration. The comparison between conduits fabricated with nanofibrous, macroporous and ladder-like microstructures showed that the ladder-like conduits showed the most favorable environment for MSC transdifferentiation to Schwann-cell like phenotypes, as seen by both immunolabeling as well as secretion of neurotrophic factors. This work demonstrates the importance of controlling the 3D microstructure to facilitate tissue engineering strategies involving stem cells that can serve as promising approaches for peripheral nerve regeneration.