Sürdürülebilir Yeşil Kampüs Koleksiyonu / Sustainable Green Campus Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7755
Browse
68 results
Search Results
Article Citation - WoS: 16Citation - Scopus: 20Groundwater Recharge Estimation Using Hydrus 1d Model in Alaşehir Sub-Basin of Gediz Basin in Turkey(Springer Verlag, 2019) Tonkul, Serhat; Baba, Alper; Şimşek, Celalettin; Durukan, Seda; Demirkesen, Ali Can; Tayfur, GökmenGediz Basin, located in the western part of Turkey constituting 2% land of the country, has an important groundwater potential in the area. Alasehir sub-basin, located in the southeast of the Gediz Basin and subject to the extensive withdrawal for the irrigation, constitutes the study area. Natural recharge to the sub-basin due to precipitation is numerically investigated in this study. For this purpose, 25 research wells, whose depths range from 20 to 50 m, were drilled to observe the recharge and collect the necessary field data for the numerical model. Meteorological data were collected from 3 weather stations installed in the study area. The numerical model HYDRUS was calibrated using the field water content data. Soil characterization was done on the core samples; the aquifer characterization was performed, and the alluvial aquifer recharge due to precipitation was calculated. As a result, the computed recharge value ranges from 21.78 to 68.52 mm, with an average value of 43.09 mm. According to the numerical model, this amount of recharge corresponds to 10% of the amount of annual rainfall.Article Citation - WoS: 15Citation - Scopus: 19Brominated Flame Retardants in a Computer Technical Service: Indoor Air Gas Phase, Submicron (pm1) and Coarse (pm10) Particles, Associated Inhalation Exposure, and Settled Dust(Elsevier Ltd., 2019) Genişoğlu, Mesut; Sofuoğlu, Aysun; Kurt Karakuş, Perihan Binnur; Birgül, Aşkın; Sofuoğlu, Sait CemilBrominated flame retardants (BFRs) are found in multi-media indoors, therefore, may pose serious risks to human health. This study investigated the occurrence of BFRs in particulate matter (PM1 and PM10) and gas phase by active and passive sampling, and settled dust to estimate potential exposure in a computer technical service. Polybrominated diphenyl ethers (PBDEs) and their alternatives (novel BFRs, NBFRs) were studied. PM and gas phase were collected on glass fiber filters and polyurethane foam plugs, respectively, and analyzed with a GC/MS after extraction, clean-up, and concentration. Inhalation exposure of the staff was estimated based on the measured concentrations using Monte Carlo simulation. BDE-209 was the dominating PBDE congener in all media while bis(2-ethylhexyl)-3,4,5,6-tetrabromophthalate and 1,2-bis(2,4,6-tribromophenoxy)ethane were those of NBFRs. Submicron particulate matter (PM1) BFR levels constituted about one half of the PM10-associated concentrations, while average PM10 mass concentration (69.9 μg m−3) was nine times that of PM1 (7.73 μg m−3). Calculated log10 dust-gas and PM-gas partitioning coefficients ranged from −5.03 to −2.10, −2.21 to −0.55, and −2.26 to −1.04 for settled dust, PM10, and PM1, respectively. The indoor/outdoor concentration ratios were >1 for all compounds indicating the strength of indoor sources in the service. The estimated potential inhalation exposures, for future chronic-toxic and carcinogenic risk assessments, indicated that the levels of gas-phase and PM1-associated exposures were similar at approximately one half of PM10-associated levels. Results of this study indicate that the occurrence of BFRs in all studied media should be taken into consideration for occupational health mitigation efforts.Article Citation - WoS: 2Citation - Scopus: 2A Deterministic and Stochastic Assessment for Exposure and Risk of Arsenic Via Ingestion of Edible Crops(Springer Verlag, 2019) Can Terzi, Begüm; Gündüz, Orhan; Sofuoğlu, Sait CemilNatural arsenic contamination is a critical problem for various places around the world. Simav Plain (Kutahya, Turkey) is one such area that was shown to have natural arsenic contamination in its waters and soils. Arsenic exposure through ingestion of edible crops cultivated in Simav Plain and associated health risks were assessed in this study. To achieve this objective, arsenic levels in 18 crop species were estimated based on measured soil arsenic concentrations. Individual and aggregate non-carcinogenic and carcinogenic risks associated with ingestion of arsenic-contaminated crops were then assessed with scenario-based deterministic point estimates and stochastic population estimates. Monte Carlo simulation was used for the estimation of population health risks. Accordingly, wheat was found as the highest-ranked crop specie for the both types of health risks, followed by tomato and potato, which are three of the most consumed crops in the region. The risk levels estimated in this study were relatively high, indicating consumption of crops grown in the plain may be posing significant health risks even at lower-bound estimates. Consuming wheat, tomato, potato, and their products from uncontaminated sources was found to reduce the aggregate risks up to 88% implicating the importance of proposing suitable management measures for similar risk-prone areas.Article Citation - WoS: 27Citation - Scopus: 28Fast Formation of Nitro-Pahs in the Marine Atmosphere Constrained in a Regional-Scale Lagrangian Field Experiment(American Chemical Society, 2019) Mulder, Marie D.; Dumanoğlu, Yetkin; Efstathiou, Christos; Kukucka, Petr; Matejovicova, Jana; Maurer, Christian; Pribylova, Petra; Prokes, Roman; Sofuoğlu, Aysun; Sofuoğlu, Sait Cemil; Wilson, Jake; Zetzsch, Cornelius; Wotawa, Gerhard; Lammel, GerhardPolycyclic aromatic hydrocarbons (PAHs) and some of their nitrated derivatives, NPAHs, are seemingly ubiquitous in the atmospheric environment. Atmospheric lifetimes may nevertheless vary within a wide range, and be as short as a few hours. The sources and sinks of NPAH in the atmosphere are not well understood. With a Lagrangian field experiment and modeling, we studied the conversion of the semivolatile PAHs fluoranthene and pyrene into the 2-nitro derivatives 2-nitrofluoranthene and 2-nitropyrene in a cloud-free marine atmosphere on the time scale of hours to 1 day between a coastal and an island site. Chemistry and transport during several episodes was simulated by a Lagrangian box model i.e., a box model coupled to a Lagrangian particle dispersion model, FLEXPART-WRF. It is found that the chemical kinetic data do capture photochemical degradation of the 4-ring PAHs under ambient conditions on the time scale of hours to 1 day, while the production of the corresponding NPAH, which sustained 2-nitrofluoranthene/fluoranthene and 2-nitropyrene/pyrene yields of (3.7 ± 0.2) and (1.5 ± 0.1)%, respectively, is by far underestimated. Predicted levels of NPAH come close to observed ones, when kinetic data describing the reactivity of the OH-adduct were explored by means of theoretically based estimates. Predictions are also underestimated by 1-2 orders of magnitude, when NPAH/PAH yields reported from laboratory experiments conducted under high NOx conditions are adopted for the simulations. It is concluded that NPAH sources effective under low NOx conditions, are largely underestimated.Article Citation - WoS: 41Citation - Scopus: 43Chloride or Sulfate? Consequences for Ozonation of Textile Wastewater(Academic Press Inc., 2019) Öktem, Yalçın Aşkın; Yüzer, Burak; Aydın, Muhammed Iberia; Ökten, Hatice Eser; Meriç, Süreyya; Selçuk, HüseyinOzonation of chloride-rich textile wastewater is a common pretreatment practice in order to increase biodegradability and therefore meet the discharge limits. This study is the first to investigate ozone-chloride/bromide interactions and formation of hazardous adsorbable organic halogens (AOX) in real textile wastewater. Initially effect of ozonation on chloride-rich real textile wastewater samples were investigated for adsorbable organic halogens (AOX) formation, biodegradability and toxicity. After 15 min of ozonation, maximum levels of chlorine/bromine generation (0.3 mg/l) and AOX formation (399 mg/l) were reached. OUR and SOUR levels both increased by approximately 58%. Daphnia magna toxicity peaked at 100% for 10 min ozonated sample. Considering adverse effects of ozonation on chloride-rich textile industry effluents, we proposed replacement of NaCl with Na2SO4. Comparative ozonation experiments were carried out for both chloride and sulfate containing synthetic dyeing wastewater samples. Results showed that use of sulfate in reactive dyeing increased biodegradability and decreased acute toxicity. Although sulfate is preferred over chloride for more effective dyeing performance, the switch has been hampered due to sodium sulfate's higher unit cost. However, consideration of indirect costs such as contributions to biodegradability, toxicity, water and salt recovery shall facilitate textile industry's switch from chloride to sulfate.Article Citation - WoS: 34Citation - Scopus: 35Development of High Flux Nanofiltration Membranes Through Single Bilayer Polyethyleneimine/Alginate Deposition(Elsevier Ltd., 2019) Tekinalp, Önder; Alsoy Altınkaya, SacideThe aim of this study is to prepare high flux, stable, antifouling nanofiltration membranes through single bilayer polyelectrolyte deposition. To this end, a tight ultrafiltration support membrane was prepared from a polysulfone/sulfonated polyethersulfone blend. Deposition of a polyethyleneimine and alginate pair on this support has reduced the molecular weight cut off from 6 kDa to below 1 kDa. The pure water permeability and polyethylene glycol 1000 rejection of the coated membrane were found to be 15.5 ± 0.3 L/m2·h·bar and 90 ± 0.6%, respectively, by setting the deposition pH for each layer to 8 and the ionic strengths to 0.5 M and 0 M. This membrane has exhibited significantly higher permeability than commercial membranes with the same molecular weight cut off, retaining 98% of the initial flux during 15 h filtration of bovine serum albumine. In addition, the membrane has been able to completely remove anionic dyes from aqueous solution by showing 99.9% retentions to Reactive red 141, Brilliant blue G and Congo red with a 2 bar transmembrane pressure. High flux and membrane stability in acidic and salty environments have been achieved when deposition conditions favor high adsorption levels for the first layer and strong ionic cross-linking between the carboxyl group on the alginate and the amine groups on the polyethyleneimineArticle Citation - WoS: 27Citation - Scopus: 34Chitosan/Montmorillonite Composite Nanospheres for Sustained Antibiotic Delivery at Post-Implantation Bone Infection Treatment(IOP Publishing Ltd., 2019) Kımna, Ceren; Değer, Sibel; Tamburacı, Sedef; Tıhmınlıoğlu, FundaDespite the advancements in bone transplantation operations, inflammation is still a serious problem that threatens human health at the post-implantation period. Conventional antibiotic therapy methods may lead to some side effects such as ototoxicity and nephrotoxicity, especially when applied in high doses. Therefore, local drug delivery systems play a vital role in bone disorders due to the elimination of the disadvantages introduced by conventional methods. In the presented study, it was aimed to develop Vancomycin (VC) and Gentamicin (GC) loaded chitosan-montmorillonite nanoclay composites (CS/MMT) to provide required antibiotic doses to combat post-implantation infection. CS/MMT nanocomposite formation was supplied by microfluidizer homogenization and spherical drug carrier nanoparticles were obtained by electrospraying technique. Three factors; voltage, distance and flowrate were varied to fabricate spherical nanoparticles with uniform size. Emprical model was developed to predict nanosphere size by altering process variables. Nanospheres were characterized in terms of morphology, hydrodynamic size, zeta potential, drug encapsulation efficiency and release profile. Drug loaded nanospheres have been successfully produced with a size range of 180-350 nm. Nanocomposite drug carriers showed high encapsulation efficiency (80%-95%) and prolonged release period when compared to bare chitosan nanospheres. The drug release from nanocomposite carriers was monitored by diffusion mechanism up to 30 d. The in vitro release medium of nanospheres showed strong antimicrobial activity against gram-positive S. aureus and gram-negative E. coli bacteria. Furthermore, it was found that the nanospheres did not show any cytotoxic effect to fibroblast (NIH/3T3) and osteoblast (SaOS-2) cell lines. The results demonstrated that the prepared composite nanospheres can be a promising option for bone infection prevention at the post implantation period.Article Citation - WoS: 370Citation - Scopus: 398Graphene-Based Adaptive Thermal Camouflage(American Chemical Society, 2018) Salihoğlu, Ömer; Uzlu, Hasan Burkay; Yakar, Ozan; Aas, Shahnaz; Balcı, Osman; Kakenov, Nurbek; Balcı, Sinan; Olçum, Selim; Süzer, Şefik; Kocabaş, CoşkunIn nature, adaptive coloration has been effectively utilized for concealment and signaling. Various biological mechanisms have evolved to tune the reflectivity for visible and ultraviolet light. These examples inspire many artificial systems for mimicking adaptive coloration to match the visual appearance to their surroundings. Thermal camouflage, however, has been an outstanding challenge which requires an ability to control the emitted thermal radiation from the surface. Here we report a new class of active thermal surfaces capable of efficient real-time electrical-control of thermal emission over the full infrared (IR) spectrum without changing the temperature of the surface. Our approach relies on electro-modulation of IR absorptivity and emissivity of multilayer graphene via reversible intercalation of nonvolatile ionic liquids. The demonstrated devices are light (30 g/m2), thin (<50 μm), and ultraflexible, which can conformably coat their environment. In addition, by combining active thermal surfaces with a feedback mechanism, we demonstrate realization of an adaptive thermal camouflage system which can reconfigure its thermal appearance and blend itself with the varying thermal background in a few seconds. Furthermore, we show that these devices can disguise hot objects as cold and cold ones as hot in a thermal imaging system. We anticipate that, the electrical control of thermal radiation would impact on a variety of new technologies ranging from adaptive IR optics to heat management for outer space applications.Article Citation - WoS: 75Citation - Scopus: 74Scaffold-Free Three-Dimensional Cell Culturing Using Magnetic Levitation(Royal Society of Chemistry, 2018) Türker, Esra; Demirçak, Nida; Arslan Yıldız, AhuThree-dimensional (3D) cell culture has emerged as a pioneering methodology and is increasingly utilized for tissue engineering, 3D bioprinting, cancer model studies and drug development studies. The 3D cell culture methodology provides artificial and functional cellular constructs serving as a modular playground prior to animal model studies, which saves substantial efforts, time and experimental costs. The major drawback of current 3D cell culture methods is their dependency on biocompatible scaffolds, which often require tedious syntheses and fabrication steps. Herein, we report an easy-to-use methodology for the formation of scaffold-free 3D cell culture and cellular assembly via magnetic levitation in the presence of paramagnetic agents. To paramagnetize the cell culture environment, three different Gadolinium(iii) chelates were utilized, which led to levitation and assembly of cells at a certain levitation height. The assembly and close interaction of cells at the levitation height where the magnetic force was equilibrated with gravitational force triggered the formation of complex 3D cellular structures. It was shown that Gd(iii) chelates provided an optimal levitation that induced intercellular interactions in scaffold-free format without compromising cell viability. NIH 3T3 mouse fibroblasts and HCC827 non-small-cell lung cancer cells were evaluated via the magnetic levitation system, and the formation of 3D cell culture models was validated for both cell lines. Hereby, the developed magnetic levitation system holds promises for complex cellular assemblies and 3D cell culture studies.Article Citation - WoS: 32Citation - Scopus: 37Mcdm Analysis of Wind Energy in Turkey: Decision Making Based on Environmental Impact(Springer Verlag, 2018) Değirmenci, Sinem; Bingöl, Ferhat; Sofuoğlu, Sait CemilDevelopment of new wind energy projects require complex planning process involving many social, technical, economic, environmental, political concerns, and different agents such as investors, utilities, governmental agencies, or social groups. The aim of this study is to develop a tool combining Geographic Information System (GIS) and Multi-Criteria Decision-Making (MCDM) methodologies, and its application for Turkey as a case study. A variety of constraints and criteria were identified based on a literature review and regulations gathered from variety of agencies, use of which resulted in determination of infeasible sites. Then, pairwise comparisons were carried out using analytic hierarchy process as the MCDM method to estimate relative importance of the criteria, and to visualize a suitability map with three classes. As the final stage, decision making was carried out based on environmental impact where 45.5% of the Turkish territory was found as infeasible area. Sixty percent of the remaining area are covered by the moderate suitability class, followed by the highly suitable area (20.3%) and low suitable area (19.8%). The output of this study can be used by energy planners to estimate the extent that wind energy can be developed based on public perception, administrative, and environmental aspects