Sürdürülebilir Yeşil Kampüs Koleksiyonu / Sustainable Green Campus Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7755
Browse
70 results
Search Results
Article Citation - WoS: 16Citation - Scopus: 20Groundwater Recharge Estimation Using Hydrus 1d Model in Alaşehir Sub-Basin of Gediz Basin in Turkey(Springer Verlag, 2019) Tonkul, Serhat; Baba, Alper; Şimşek, Celalettin; Durukan, Seda; Demirkesen, Ali Can; Tayfur, GökmenGediz Basin, located in the western part of Turkey constituting 2% land of the country, has an important groundwater potential in the area. Alasehir sub-basin, located in the southeast of the Gediz Basin and subject to the extensive withdrawal for the irrigation, constitutes the study area. Natural recharge to the sub-basin due to precipitation is numerically investigated in this study. For this purpose, 25 research wells, whose depths range from 20 to 50 m, were drilled to observe the recharge and collect the necessary field data for the numerical model. Meteorological data were collected from 3 weather stations installed in the study area. The numerical model HYDRUS was calibrated using the field water content data. Soil characterization was done on the core samples; the aquifer characterization was performed, and the alluvial aquifer recharge due to precipitation was calculated. As a result, the computed recharge value ranges from 21.78 to 68.52 mm, with an average value of 43.09 mm. According to the numerical model, this amount of recharge corresponds to 10% of the amount of annual rainfall.Article Citation - WoS: 15Citation - Scopus: 19Brominated Flame Retardants in a Computer Technical Service: Indoor Air Gas Phase, Submicron (pm1) and Coarse (pm10) Particles, Associated Inhalation Exposure, and Settled Dust(Elsevier Ltd., 2019) Genişoğlu, Mesut; Sofuoğlu, Aysun; Kurt Karakuş, Perihan Binnur; Birgül, Aşkın; Sofuoğlu, Sait CemilBrominated flame retardants (BFRs) are found in multi-media indoors, therefore, may pose serious risks to human health. This study investigated the occurrence of BFRs in particulate matter (PM1 and PM10) and gas phase by active and passive sampling, and settled dust to estimate potential exposure in a computer technical service. Polybrominated diphenyl ethers (PBDEs) and their alternatives (novel BFRs, NBFRs) were studied. PM and gas phase were collected on glass fiber filters and polyurethane foam plugs, respectively, and analyzed with a GC/MS after extraction, clean-up, and concentration. Inhalation exposure of the staff was estimated based on the measured concentrations using Monte Carlo simulation. BDE-209 was the dominating PBDE congener in all media while bis(2-ethylhexyl)-3,4,5,6-tetrabromophthalate and 1,2-bis(2,4,6-tribromophenoxy)ethane were those of NBFRs. Submicron particulate matter (PM1) BFR levels constituted about one half of the PM10-associated concentrations, while average PM10 mass concentration (69.9 μg m−3) was nine times that of PM1 (7.73 μg m−3). Calculated log10 dust-gas and PM-gas partitioning coefficients ranged from −5.03 to −2.10, −2.21 to −0.55, and −2.26 to −1.04 for settled dust, PM10, and PM1, respectively. The indoor/outdoor concentration ratios were >1 for all compounds indicating the strength of indoor sources in the service. The estimated potential inhalation exposures, for future chronic-toxic and carcinogenic risk assessments, indicated that the levels of gas-phase and PM1-associated exposures were similar at approximately one half of PM10-associated levels. Results of this study indicate that the occurrence of BFRs in all studied media should be taken into consideration for occupational health mitigation efforts.Article Citation - WoS: 2Citation - Scopus: 2A Deterministic and Stochastic Assessment for Exposure and Risk of Arsenic Via Ingestion of Edible Crops(Springer Verlag, 2019) Can Terzi, Begüm; Gündüz, Orhan; Sofuoğlu, Sait CemilNatural arsenic contamination is a critical problem for various places around the world. Simav Plain (Kutahya, Turkey) is one such area that was shown to have natural arsenic contamination in its waters and soils. Arsenic exposure through ingestion of edible crops cultivated in Simav Plain and associated health risks were assessed in this study. To achieve this objective, arsenic levels in 18 crop species were estimated based on measured soil arsenic concentrations. Individual and aggregate non-carcinogenic and carcinogenic risks associated with ingestion of arsenic-contaminated crops were then assessed with scenario-based deterministic point estimates and stochastic population estimates. Monte Carlo simulation was used for the estimation of population health risks. Accordingly, wheat was found as the highest-ranked crop specie for the both types of health risks, followed by tomato and potato, which are three of the most consumed crops in the region. The risk levels estimated in this study were relatively high, indicating consumption of crops grown in the plain may be posing significant health risks even at lower-bound estimates. Consuming wheat, tomato, potato, and their products from uncontaminated sources was found to reduce the aggregate risks up to 88% implicating the importance of proposing suitable management measures for similar risk-prone areas.Article Citation - WoS: 27Citation - Scopus: 28Fast Formation of Nitro-Pahs in the Marine Atmosphere Constrained in a Regional-Scale Lagrangian Field Experiment(American Chemical Society, 2019) Mulder, Marie D.; Dumanoğlu, Yetkin; Efstathiou, Christos; Kukucka, Petr; Matejovicova, Jana; Maurer, Christian; Pribylova, Petra; Prokes, Roman; Sofuoğlu, Aysun; Sofuoğlu, Sait Cemil; Wilson, Jake; Zetzsch, Cornelius; Wotawa, Gerhard; Lammel, GerhardPolycyclic aromatic hydrocarbons (PAHs) and some of their nitrated derivatives, NPAHs, are seemingly ubiquitous in the atmospheric environment. Atmospheric lifetimes may nevertheless vary within a wide range, and be as short as a few hours. The sources and sinks of NPAH in the atmosphere are not well understood. With a Lagrangian field experiment and modeling, we studied the conversion of the semivolatile PAHs fluoranthene and pyrene into the 2-nitro derivatives 2-nitrofluoranthene and 2-nitropyrene in a cloud-free marine atmosphere on the time scale of hours to 1 day between a coastal and an island site. Chemistry and transport during several episodes was simulated by a Lagrangian box model i.e., a box model coupled to a Lagrangian particle dispersion model, FLEXPART-WRF. It is found that the chemical kinetic data do capture photochemical degradation of the 4-ring PAHs under ambient conditions on the time scale of hours to 1 day, while the production of the corresponding NPAH, which sustained 2-nitrofluoranthene/fluoranthene and 2-nitropyrene/pyrene yields of (3.7 ± 0.2) and (1.5 ± 0.1)%, respectively, is by far underestimated. Predicted levels of NPAH come close to observed ones, when kinetic data describing the reactivity of the OH-adduct were explored by means of theoretically based estimates. Predictions are also underestimated by 1-2 orders of magnitude, when NPAH/PAH yields reported from laboratory experiments conducted under high NOx conditions are adopted for the simulations. It is concluded that NPAH sources effective under low NOx conditions, are largely underestimated.Article Citation - WoS: 41Citation - Scopus: 43Chloride or Sulfate? Consequences for Ozonation of Textile Wastewater(Academic Press Inc., 2019) Öktem, Yalçın Aşkın; Yüzer, Burak; Aydın, Muhammed Iberia; Ökten, Hatice Eser; Meriç, Süreyya; Selçuk, HüseyinOzonation of chloride-rich textile wastewater is a common pretreatment practice in order to increase biodegradability and therefore meet the discharge limits. This study is the first to investigate ozone-chloride/bromide interactions and formation of hazardous adsorbable organic halogens (AOX) in real textile wastewater. Initially effect of ozonation on chloride-rich real textile wastewater samples were investigated for adsorbable organic halogens (AOX) formation, biodegradability and toxicity. After 15 min of ozonation, maximum levels of chlorine/bromine generation (0.3 mg/l) and AOX formation (399 mg/l) were reached. OUR and SOUR levels both increased by approximately 58%. Daphnia magna toxicity peaked at 100% for 10 min ozonated sample. Considering adverse effects of ozonation on chloride-rich textile industry effluents, we proposed replacement of NaCl with Na2SO4. Comparative ozonation experiments were carried out for both chloride and sulfate containing synthetic dyeing wastewater samples. Results showed that use of sulfate in reactive dyeing increased biodegradability and decreased acute toxicity. Although sulfate is preferred over chloride for more effective dyeing performance, the switch has been hampered due to sodium sulfate's higher unit cost. However, consideration of indirect costs such as contributions to biodegradability, toxicity, water and salt recovery shall facilitate textile industry's switch from chloride to sulfate.Article Citation - WoS: 34Citation - Scopus: 35Development of High Flux Nanofiltration Membranes Through Single Bilayer Polyethyleneimine/Alginate Deposition(Elsevier Ltd., 2019) Tekinalp, Önder; Alsoy Altınkaya, SacideThe aim of this study is to prepare high flux, stable, antifouling nanofiltration membranes through single bilayer polyelectrolyte deposition. To this end, a tight ultrafiltration support membrane was prepared from a polysulfone/sulfonated polyethersulfone blend. Deposition of a polyethyleneimine and alginate pair on this support has reduced the molecular weight cut off from 6 kDa to below 1 kDa. The pure water permeability and polyethylene glycol 1000 rejection of the coated membrane were found to be 15.5 ± 0.3 L/m2·h·bar and 90 ± 0.6%, respectively, by setting the deposition pH for each layer to 8 and the ionic strengths to 0.5 M and 0 M. This membrane has exhibited significantly higher permeability than commercial membranes with the same molecular weight cut off, retaining 98% of the initial flux during 15 h filtration of bovine serum albumine. In addition, the membrane has been able to completely remove anionic dyes from aqueous solution by showing 99.9% retentions to Reactive red 141, Brilliant blue G and Congo red with a 2 bar transmembrane pressure. High flux and membrane stability in acidic and salty environments have been achieved when deposition conditions favor high adsorption levels for the first layer and strong ionic cross-linking between the carboxyl group on the alginate and the amine groups on the polyethyleneimineArticle Citation - WoS: 27Citation - Scopus: 34Chitosan/Montmorillonite Composite Nanospheres for Sustained Antibiotic Delivery at Post-Implantation Bone Infection Treatment(IOP Publishing Ltd., 2019) Kımna, Ceren; Değer, Sibel; Tamburacı, Sedef; Tıhmınlıoğlu, FundaDespite the advancements in bone transplantation operations, inflammation is still a serious problem that threatens human health at the post-implantation period. Conventional antibiotic therapy methods may lead to some side effects such as ototoxicity and nephrotoxicity, especially when applied in high doses. Therefore, local drug delivery systems play a vital role in bone disorders due to the elimination of the disadvantages introduced by conventional methods. In the presented study, it was aimed to develop Vancomycin (VC) and Gentamicin (GC) loaded chitosan-montmorillonite nanoclay composites (CS/MMT) to provide required antibiotic doses to combat post-implantation infection. CS/MMT nanocomposite formation was supplied by microfluidizer homogenization and spherical drug carrier nanoparticles were obtained by electrospraying technique. Three factors; voltage, distance and flowrate were varied to fabricate spherical nanoparticles with uniform size. Emprical model was developed to predict nanosphere size by altering process variables. Nanospheres were characterized in terms of morphology, hydrodynamic size, zeta potential, drug encapsulation efficiency and release profile. Drug loaded nanospheres have been successfully produced with a size range of 180-350 nm. Nanocomposite drug carriers showed high encapsulation efficiency (80%-95%) and prolonged release period when compared to bare chitosan nanospheres. The drug release from nanocomposite carriers was monitored by diffusion mechanism up to 30 d. The in vitro release medium of nanospheres showed strong antimicrobial activity against gram-positive S. aureus and gram-negative E. coli bacteria. Furthermore, it was found that the nanospheres did not show any cytotoxic effect to fibroblast (NIH/3T3) and osteoblast (SaOS-2) cell lines. The results demonstrated that the prepared composite nanospheres can be a promising option for bone infection prevention at the post implantation period.Article Citation - WoS: 19Citation - Scopus: 29Modeling of an Activated Sludge Process for Effluent Prediction—a Comparative Study Using Anfis and Glm Regression(Springer Verlag, 2018) Araromi, Dauda Olurotimi; Majekodunmi, Olukayode Titus; Adeniran, Jamiu Adetayo; Salawudeen, Taofeeq OlalekanIn this paper, nonlinear system identification of the activated sludge process in an industrial wastewater treatment plant was completed using adaptive neuro-fuzzy inference system (ANFIS) and generalized linear model (GLM) regression. Predictive models of the effluent chemical and 5-day biochemical oxygen demands were developed from measured past inputs and outputs. From a set of candidates, least absolute shrinkage and selection operator (LASSO), and a fuzzy brute-force search were utilized in selecting the best combination of regressors for the GLMs and ANFIS models respectively. Root mean square error (RMSE) and Pearson’s correlation coefficient (R-value) served as metrics in assessing the predicting performance of the models. Contrasted with the GLM predictions, the obtained modeling results show that the ANFIS models provide better predictions of the studied effluent variables. The results of the empirical search for the dominant regressors indicate the models have an enormous potential in the estimation of the time lag before a desired effluent quality can be realized, and preempting process disturbances. Hence, the models can be used in developing a software tool that will facilitate the effective management of the treatment operation.Article Citation - WoS: 91Citation - Scopus: 95Source Apportionment and Carcinogenic Risk Assessment of Passive Air Sampler-Derived Pahs and Pcbs in a Heavily Industrialized Region(Elsevier Ltd., 2018) Çetin, Banu; Yurdakul, Sema; Güngörmüş, Elif; Öztürk, Fatma; Sofuoğlu, Sait CemilCancer has become the primary reason of deaths in Dilovasi probably due to its location with unique topography under the influence of heavy industrialization and traffic. In this study, possible sources and carcinogenic health risks of PAHs and PCBs were investigated in Dilovasi region by Positive Matrix Factorization (PMF) and the USEPA approach, respectively. PAHs and PCBs were measured monthly for a whole year at 23 sampling sites using PUF disk passive samplers. Average ambient air concentrations were found as 285 ± 431 ng/m 3 and 4152 ± 6072 pg/m 3 , for Σ 15 PAH and Σ 41 PCB, respectively. PAH concentrations increased with decreasing temperature especially at urban sites, indicating the impact of residential heating in addition to industrial activities and traffic. On the other hand, PCB concentrations mostly increased with temperature probably due to enhanced volatilization from their sources. Possible sources of PAHs were found as emissions of diesel and gasoline vehicles, biomass and coal combustion, iron and steel industry, and unburned petroleum/petroleum products, whereas iron-steel production, coal and biomass burning, technical PCB mixtures, and industrial emissions were identified for PCBs. The mean carcinogenic risk associated with inhalation exposure to PAHs and PCBs were estimated to be >10 −6 and >10 −5 , respectively, at all sampling points, while the 95th percentile was >10 −5 at 15 of 23 and >10 −4 at 8 of 23 sampling locations, respectively. Probabilistic assessment showed, especially for PCBs, that a majority of Dilovasi population face significant health risks. The higher risks due to PCBs further indicated that PCBs and possibly other pollutants originating from the same sources such as PBDEs and PCNs may be an important issue for the region.Article Citation - WoS: 370Citation - Scopus: 398Graphene-Based Adaptive Thermal Camouflage(American Chemical Society, 2018) Salihoğlu, Ömer; Uzlu, Hasan Burkay; Yakar, Ozan; Aas, Shahnaz; Balcı, Osman; Kakenov, Nurbek; Balcı, Sinan; Olçum, Selim; Süzer, Şefik; Kocabaş, CoşkunIn nature, adaptive coloration has been effectively utilized for concealment and signaling. Various biological mechanisms have evolved to tune the reflectivity for visible and ultraviolet light. These examples inspire many artificial systems for mimicking adaptive coloration to match the visual appearance to their surroundings. Thermal camouflage, however, has been an outstanding challenge which requires an ability to control the emitted thermal radiation from the surface. Here we report a new class of active thermal surfaces capable of efficient real-time electrical-control of thermal emission over the full infrared (IR) spectrum without changing the temperature of the surface. Our approach relies on electro-modulation of IR absorptivity and emissivity of multilayer graphene via reversible intercalation of nonvolatile ionic liquids. The demonstrated devices are light (30 g/m2), thin (<50 μm), and ultraflexible, which can conformably coat their environment. In addition, by combining active thermal surfaces with a feedback mechanism, we demonstrate realization of an adaptive thermal camouflage system which can reconfigure its thermal appearance and blend itself with the varying thermal background in a few seconds. Furthermore, we show that these devices can disguise hot objects as cold and cold ones as hot in a thermal imaging system. We anticipate that, the electrical control of thermal radiation would impact on a variety of new technologies ranging from adaptive IR optics to heat management for outer space applications.