Sürdürülebilir Yeşil Kampüs Koleksiyonu / Sustainable Green Campus Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7755
Browse
23 results
Search Results
Now showing 1 - 10 of 23
Article Citation - WoS: 16Citation - Scopus: 20Groundwater Recharge Estimation Using Hydrus 1d Model in Alaşehir Sub-Basin of Gediz Basin in Turkey(Springer Verlag, 2019) Tonkul, Serhat; Baba, Alper; Şimşek, Celalettin; Durukan, Seda; Demirkesen, Ali Can; Tayfur, GökmenGediz Basin, located in the western part of Turkey constituting 2% land of the country, has an important groundwater potential in the area. Alasehir sub-basin, located in the southeast of the Gediz Basin and subject to the extensive withdrawal for the irrigation, constitutes the study area. Natural recharge to the sub-basin due to precipitation is numerically investigated in this study. For this purpose, 25 research wells, whose depths range from 20 to 50 m, were drilled to observe the recharge and collect the necessary field data for the numerical model. Meteorological data were collected from 3 weather stations installed in the study area. The numerical model HYDRUS was calibrated using the field water content data. Soil characterization was done on the core samples; the aquifer characterization was performed, and the alluvial aquifer recharge due to precipitation was calculated. As a result, the computed recharge value ranges from 21.78 to 68.52 mm, with an average value of 43.09 mm. According to the numerical model, this amount of recharge corresponds to 10% of the amount of annual rainfall.Master Thesis Hec Hms Hydrological Model Application Using Scs Curve Number and Soil Moisture Accounting: Case Study of Alaşehir Basin(Izmir Institute of Technology, 2019) Akdeğirmen, Özgün; Baba, Alper; Tayfur, GökmenWater is known as source of life throughout mankind’s history. According to first records of written history; Sumerians and Akkadians used water for their inland transportation and irrigation systems. With first settlements, mankind’s dependency to water has been increased and became one of the most substantial natural resource in our modern age. Importance of this resource even more solidifies when we consider its property of being limited. With realization of global climate change in early 19th century; treat to this limited resource has been revealed. Approximately 68% of the freshwater on earth reserved in glaciers and icecaps and 30% is reserved in groundwater systems according to United States Geological Survey’s (USGS) studies. Owing to the quantity and less compromised to contaminants nature, majority of our freshwater needs met from groundwater. Although the importance of groundwater, its management have always been a challenge due to hard to quantify volumetric changings in aquifers. This study focused on creating a hydrological basin model to investigate volumetric recharge changings in groundwater system. Under scope of this study in an attempt to acquire groundwater recharge amounts; practicality of HEC-HMS hydrological modeling software has been investigated. A SCS Curve Number and Soil Moisture Accounting (SMA) loss methods has been chosen for HEC-HMS modeling application due to availability and accessibility of data that required for loss methods. After data collection from meteorological stations, core drill samples; both methods have been used in HEC-HMS simulation environment and their predictions have been compared. In the comparisons, it was determined that the SCS Curve Number method predicts higher flow potentials and groundwater infiltration amounts compared to the SMA method. Models foresee an average of 33.4 % of precipitation infiltrates into groundwater system.Master Thesis Numerical Modeling the Flood Wave as a Result of Ürkmez Dam(Izmir Institute of Technology, 2018) Şahin, Gül Sümeyra; Tayfur, GökmenDams are constructed to provide benefits to society, hydropower generation, including water supply management and flood control. However, floods caused by failure of a dam is quite catastrophic for lives, properties and environment. Flow models for dam break scenarios ensures crucial information about land use planning and risk managment to minimize flood losses. In this study, estimation of flood innundated areas caused by flood triggered by failure of Urkmez Dam in Izmir is carried out by using HEC-RAS onedimensional (1D) unsteady flow routing model (full Saint Venant equations) and two dimensional model (2D) (full Saint Venant equations or Diffusion wave equations). The experimental distorted physical model provides controlling to simulations. The aim of the paper is to assess the risk of a dam failure potential by comparing performances of 1D and 2D simulations. Two models were compared considering the required data, data preparation, inundated area, flood velocity, flood depth, and flood waves.Article Citation - WoS: 18Citation - Scopus: 24Empirical Sediment Transport Models Based on Indoor Rainfall Simulator and Erosion Flume Experimental Data(John Wiley and Sons Inc., 2017) Aksoy, Hafzullah; Eriş, Ebru; Tayfur, GökmenLand degradation processes start with accelerated runoff and sediment delivery. In this study, rainfall-runoff induced sediment transport is investigated using data from an indoor laboratory experimental setup consisting of a rainfall simulator and an erosion flume. The data are analysed to develop empirical models using sediment discharge, slope, flow discharge, rainfall intensity and sediment size. Fine and medium sands are considered as bare soil in experiments. Four rainfall intensities (45, 65, 85 and 105 mm h−1) are applied with combinations of lateral and longitudinal slopes of 5%, 10%, 15% and 20%. Eighty experiments are conducted. Flow is measured, and sediment within flow is separated and weighted. Experimental data are used for developing empirical models through multiple regression with parameters optimized by genetic algorithm. Results show that slope is the main contributing variable to the sediment transport over hillslopes. Accommodating variables among slope, rainfall intensity, flow discharge and median diameter of sediment as independent variables, one-variable, two-variable and four-variable models are developed considering also that higher number of parameters increases the performance of the model with higher cost of parameterization.Article Citation - WoS: 45Citation - Scopus: 51Evaluation and Assessment of Meteorological Drought by Different Methods in Trarza Region, Mauritania(Springer Verlag, 2017) Yacoub, Ely; Tayfur, GökmenDrought Indexes (DIs) are commonly used for assessing the effect of drought such as the duration and severity. In this study, long term precipitation records (monthly recorded for 44 years) in three stations (Boutilimit (station 1), Nouakchott (station 2), and Rosso (station 3)) are employed to investigate the drought characteristics in Trarza region in Mauritania. Six DI methods, namely normal Standardized Precipitation Index (normal-SPI), log normal Standardized Precipitation Index (log-SPI), Standardized Precipitation Index using Gamma distribution (Gamma-SPI), Percent of Normal (PN), the China-Z index (CZI), and Deciles are used for this purpose. The DI methods are based on 1-, 3-, 6-, and 12 month time periods. The results showed that DIs produce almost the same results for the Trarza region. The droughts are detected in the seventies and eighties more than the 1990s. Twelve drought years might be experienced in station 2 and six in stations 1 and 3 in every 44 years, according to reoccurrence probability of the gamma-SPI and log-SPI results. Stations 1 and 3 might experience fewer drought years than station 2, which is located right on the coast. In station 1, which is located inland, when the annual rainfall is less than 123 mm, it is likely that severe drought would occur. This is 63 mm/year for station 2 and 205 mm/year for station 3 which is located in the south west on the Senegal River. DI results indicate that the CZI and the gamma-SPI methods make similar predictions and the log-SPI makes extreme drought predictions for the monthly period for all the stations. For longer periods (3-, 6-, and 12 month period), for all the stations, the log-SPI and the gamma-SPI produce similar results, making severe drought predictions while the normal-SPI and the CZI methods predict more wet and fewer drought cases. The log-SPI, the gamma-SPI, PN and Deciles were able to capture the historical extreme and severe droughts observed in early 1970s and early 1980s.Article Citation - WoS: 76Citation - Scopus: 84Two-Dimensional Numerical Modeling of Flood Wave Propagation in an Urban Area Due To Ürkmez Dam-Break, Izmir, Turkey(Springer Verlag, 2016) Haltas, İsmail; Tayfur, Gökmen; Elçi, ŞebnemThis study investigated flood inundation in an urban area due to a possible failure of Ürkmez Dam in İzmir, Turkey. The estimation of flood hydrograph upon partial failure of the dam and routing of the flood hydrograph along the narrow valley downstream were first performed by the one-dimensional hydraulic routing model HEC-RAS. The two-dimensional hydraulic routing model FLO-2D is then used to simulate the spreading of the dam-break flood after the flood wave exits the valley. Land use and land cover digital maps were utilized to find the spatially varying roughness coefficient for the floodplain. The influence of the buildings on the flood propagation was represented in the numerical model by the area reduction factor as well as the width reduction factor. The peak flow depth, peak flow velocity and time moment of the peak flow depth maps were shown in the GIS environment. The results reveal that flow depths can reach about 3 m in the residential area. In about 40 min after the dam-break, houses in the large section of the town would be under the maximum flow depths. The two-dimensional hydrodynamic model results were tested against experimental dam-break flow data of the distorted physical model of Ürkmez Dam, which is consisted of the reservoir, dam body and downstream area including Ürkmez Town. The model successfully simulated experimental flow depth data measured at different measurement locations.Article Citation - WoS: 27Citation - Scopus: 28Reverse flood routing in natural channels using genetic algorithm(Springer Verlag, 2015) Zucco, Graziano; Tayfur, Gökmen; Moramarco, TommasoEstablishing a clear overview of data discharge availability for water balance modelling in basins is a priority in Europe, and in the particular in the framework of the system of Economic and Environmental Accounts for Water (SEEAW) developed by the EU Directorate-General for the Environment. However, accurate discharge estimation at a river site depends on rating curve reliability usually defined by recording the water level at a gauged section and carrying out streamflow measurements. Local stage monitoring is fairly straightforward and relatively inexpensive compared to the cost to carry out flow velocity measurements which are, in addition, hindered by high flow. Moreover, hydraulic models may not be ideally suitable to serve the purpose of rating curve extension or its development at a river site upstream/downstream where the discharge is known due to their prohibitive requirement of channel cross-section details and roughness information at closer intervals. Likewise, rainfall-runoff transformation might be applied but its accuracy is tightly linked to detailed information in terms of geomorphological characteristics of intermediate basins as well as rainfall pattern data. On this basis, a procedure for reverse flood routing in natural channels is here proposed for three different configurations of hydrometric monitoring of a river reach where lateral flow is significant and no rainfall data are available for the intermediate basin. The first considers only the downstream channel end as a gauged site where discharge and stages are recorded. The second configuration assumes the downstream end as a gauged site but only in terms of stage. The third configuration envisages both channel ends equipped to recording stages. The channel geometry is known only at channel ends. The developed model has basically four components: (1) the inflow hydrograph is expressed by a Pearson Type-III distribution, involving parameters of peak discharge, time to peak, and a shape factor; (2) the basic continuity equation for flow routing written in the characteristic form is employed; (3) the lateral flow is related to stages at channel ends. (4) the relation between local stage and remote discharge as found by Moramarco et al. (2005b) is exploited. The parameters, coefficients and exponents of the model are obtained, for each configuration, using the genetic algorithm method. Three equipped river branches along the Tiber River in central Italy are used to validate the procedure. Analyses are carried out for three significant flood events occurred along the river and where the lateral flow was significant. Results show the good performance of the procedure for all three monitoring configurations. Specifically, the discharge hydrographs assessed at channel ends are found satisfactory both in terms of shape with a Nash-Sutcliffe ranging overall in the interval (0.755–0.972) and in the reproduction of rating curves at channel ends. Finally, by a synthetic test the performance of the developed procedure is compared to that of the hydraulic model coupled with a hydrologic model. Two river reaches are considered, the first along the Tiber River and the second one located in the Rio Grande basin which is a tributary of the Tiber River. Detailed channel geometry data are available for both the river sections. Results showed the effectiveness of the reverse flood routing to reproducing fairly well the hydrographs simulated by the hydraulic model in the three monitoring investigated configurations.Master Thesis B and Se Transport Modeling in Saturated/Unsaturated Zones(Izmir Institute of Technology, 2002) Yüreklitürk, O. Emin; Tayfur, GökmenThere has been renewed interest in the application of models to the transport of non-point source pollutants. However, very little work has been done to evaluate the performance of a functional transient-state model for the transport of a reactive solute over an extensive study period. This research consists of mathematical modeling to simulate water flow, boron and selenium transport through soil in tile-drained croplands.For Boron part a mathematical model was developed to simulate non-conservative boron transport. The dynamic two-dimensional finite element model simulates water flow and boron transport in saturated-unsaturated soil system, including boron sorption and boron uptake by root-water extraction. Two different models have been employed for the sorption of boron. Similarly, for selenium part a finite element model is developed to simulate species of selenium transport in two dimensions in saturated/unsaturated zones. The model considers water, selenate, selenite and selenomethionine uptake by plants. It also considers oxidation/reduction, volatilization, and chemical and biological transformations of selenate, selenite, and selenomethionine. Comparison of boron transport model results with observed data is satisfactory. The model employed with Langmuir isotherm was found to give slightly better simulation results when compared with the model employed with Freundlich. The sensitivity analysis results indicate that the irrigation scheduling and the irrigation water quality are very important parameters for boron accumulation in the soil. Also the adsorption isotherm parameters, which reflect us the soil properties, are found to be important for the boron movement in the soil. Comparison of selenium transport model with observed data is not quite satisfactory in accuracy when compared with the model for boron transport. This may be the result of the complexity of the mechanisms affecting the selenium transport in soil. There are too many parameters, and due to the errors depending on the parameters, the total error for the estimation of the total selenium increases.Article Citation - WoS: 3Citation - Scopus: 3Simulating Transient Sediment Waves in Aggraded Alluvial Channels by Double-Decomposition Method(American Society of Civil Engineers (ASCE), 2011) Tayfur, Gökmen; Singh, Vijay P.By using the double-decomposition (DD) method, this study simulates transient sediment waves caused by aggradation described by a diffusion-type partial differential equation (PDE). The DD method solves the PDE by decomposing the solution function for sediment rate into a summation of M number of components, where M stands for the order of approximation. The solution was approximated by considering only the first three terms. The model satisfactorily simulated laboratory-measured aggradation bed profiles with, on average, a mean absolute error (MAE) of 0.70 cm, a root-mean-square error (RMSE) of 0.84 cm, a mean relative error (MRE) of 1.11%, and R2=0.95. The model performance was also tested by using numerical and error-function solutions. In addition, the results obtained from application of the DD solution to hypothetical field cases were found to be theoretically compatible with what may be observed in natural streams. However, sediment wave fronts in later periods of the simulation time reached equilibrium bed levels more quickly, around in the middle section of the channel.Article Citation - WoS: 73Citation - Scopus: 84Groundwater Contamination and Its Effect on Health in Turkey(Springer Verlag, 2011) Baba, Alper; Tayfur, GökmenThe sources of groundwater pollution in Turkey are identified, and pathways of contaminants to groundwater are first described. Then, the effects of groundwater quality on health in Turkey are evaluated. In general, sources of groundwater contamination fall into two main categories: natural and anthropogenic sources. Important sources of natural groundwater pollution in Turkey include geological formations, seawater intrusion, and geothermal fluid(s). The major sources of anthropogenic groundwater contamination are agricultural activities, mining waste, industrial waste, on-site septic tank systems, and pollution from imperfect well constructions. The analysis results revealed that natural contamination due to salt and gypsum are mostly found in Central and Mediterranean regions and arsenic in Aegean region. Geothermal fluids which contain fluoride poses a danger for skeleton, dental, and bone problems, especially in the areas of Denizli, Isparta, and AydIn. Discharges from surface water bodies contaminate groundwater by infiltration. Evidence of such contamination is found in Upper KIzIlIrmak basin, Gediz basin, and Büyük Melen river basin and some drinking water reservoirs in Istanbul. Additionally, seawater intrusion causes groundwater quality problems in coastal regions, especially in the Aegean coast. Industrial wastes are also polluting surface and groundwater in industrialized regions of Turkey. Deterioration of water quality as a result of fertilizers and pesticides is another major problem especially in the regions of Mediterranean, Aegean, Central Anatolia, and Marmara. Abandoned mercury mines in the western regions of Turkey, especially in Çanakkale, Izmir, Muǧla, Kütahya, and BalIkesir, cause serious groundwater quality problems. © 2011 Springer Science+Business Media B.V.
- «
- 1 (current)
- 2
- 3
- »