Bioengineering / Biyomühendislik
Permanent URI for this collectionhttps://hdl.handle.net/11147/4529
Browse
4 results
Search Results
Now showing 1 - 4 of 4
Article Citation - WoS: 25Citation - Scopus: 30Fabrication of 3d Printed Poly(lactic Acid) Strut and Wet-Electrospun Cellulose Nano Fiber Reinforced Chitosan-Collagen Hydrogel Composite Scaffolds for Meniscus Tissue Engineering(SAGE Publications, 2022) Güneş, Oylum Çolpankan; Kara, Aylin; Baysan, Gizem; Hüsemoğlu, Reşit Buğra; Akokay, Pınar; Ziylan Albayrak, Aylin; Ergür, Bekir Uğur; Havitçioğlu, HasanThe main goal of the study was to produce chitosan-collagen hydrogel composite scaffolds consisting of 3D printed poly(lactic acid) (PLA) strut and nanofibrous cellulose for meniscus cartilage tissue engineering. For this purpose, first PLA strut containing microchannels was incorporated into cellulose nanofibers and then they were embedded into chitosan-collagen matrix to obtain micro- and nano-sized topographical features for better cellular activities as well as mechanical properties. All the hydrogel composite scaffolds produced by using three different concentrations of genipin (0.1, 0.3, and 0.5%) had an interconnected microporous structure with a swelling ratio of about 400% and water content values between 77 and 83% which is similar to native cartilage extracellular matrix. The compressive strength of all the hydrogel composite scaffolds was found to be similar (∼32 kPa) and suitable for cartilage tissue engineering applications. Besides, the hydrogel composite scaffold comprising 0.3% (w/v) genipin had the highest tan δ value (0.044) at a frequency of 1 Hz which is around the walking frequency of a person. According to the in vitro analysis, this hydrogel composite scaffold did not show any cytotoxic effect on the rabbit mesenchymal stem cells and enabled cells to attach, proliferate and also migrate through the inner area of the scaffold. In conclusion, the produced hydrogel composite scaffold holds great promise for meniscus tissue engineering.Article Citation - WoS: 51Citation - Scopus: 583d Printed Gelatin/Decellularized Bone Composite Scaffolds for Bone Tissue Engineering: Fabrication, Characterization and Cytocompatibility Study(Elsevier, 2022) Kara, Aylin; Distler, Thomas; Polley, Christian; Schneidereit, Dominik; Seitz, Hermann; Friedrich, Oliver; Tıhmınlıoğlu, Funda; Boccaccini, Aldo RThree-dimensional (3D) printing technology enables the design of personalized scaffolds with tunable pore size and composition. Combining decellularization and 3D printing techniques provides the opportunity to fabricate scaffolds with high potential to mimic native tissue. The aim of this study is to produce novel decellularized bone extracellular matrix (dbECM)-reinforced composite-scaffold that can be used as a biomaterial for bone tissue engineering. Decellularized bone particles (dbPTs, ∼100 μm diameter) were obtained from rabbit femur and used as a reinforcement agent by mixing with gelatin (GEL) in different concentrations. 3D scaffolds were fabricated by using an extrusion-based bioprinter and crosslinking with microbial transglutaminase (mTG) enzyme, followed by freeze-drying to obtain porous structures. Fabricated 3D scaffolds were characterized morphologically, mechanically, and chemically. Furthermore, MC3T3-E1 mouse pre-osteoblast cells were seeded on the dbPTs reinforced GEL scaffolds (GEL/dbPTs) and cultured for 21 days to assess cytocompatibility and cell attachment. We demonstrate the 3D-printability of dbPTs-reinforced GEL hydrogels and the achievement of homogenous distribution of the dbPTs in the whole scaffold structure, as well as bioactivity and cytocompatibility of GEL/dbPTs scaffolds. It was shown that Young's modulus and degradation rate of scaffolds were enhanced with increasing dbPTs content. Multiphoton microscopy imaging displayed the interaction of cells with dbPTs, indicating attachment and proliferation of cells around the particles as well as into the GEL-particle hydrogels. Our results demonstrate that GEL/dbPTs hydrogel formulations have potential for bone tissue engineering.Article Citation - WoS: 14Citation - Scopus: 17Biocompatibility of Silicon Nitride Produced Via Partial Sintering & Tape Casting(Elsevier Ltd., 2021) Çeçen, Berivan; Topateş, Gülsüm; Kara, Aylin; Akbulut, Serdar Onat; Havıtçıoğlu, Hasan; Kozacı, Leyla DidemThe biocompatibility of silicon nitride ceramics was proven by several studies however this study is apart from the literature in the manner of production routes that are tape casting and partial sintering. We report the tape casting route was chosen and a porous structure was obtained by partial sintering technique. Tape casting brought a smooth surface to the samples. Density and pore size distribution analysis showed that the scaffolds have low density because of the porous structure. XRD and SEM analyses were carried out to reveal the phase and microstructural characteristics of porous ceramic samples. Static contact angle measurement was done for the characterization of the wettability of the scaffolds. It revealed that the surface of the scaffolds was highly hydrophilic which is a desirable characteristic for the protein and cell adhesion. The mechanical characteristics of the scaffolds were analyzed by compression tests. Human osteosarcoma cells were used for in vitro studies. Cell-proliferation and cytotoxicity were analyzed by WST-1 and LDH, respectively. The osteoblastic behavior of the cells on the surface of the scaffolds was identified by alkaline phosphatase activity. BCA analysis was used for total protein content. The BCA and ALP results showed an increasing trend which is directly correlated with cell proliferation. Cells on the surface of the silicon nitride scaffolds were visualized by SEM and fluorescence microscopy where the images supported the in vitro analysis. Therefore, porous silicon nitride scaffolds fabricated via tape casting and partial sintering were biocompatible and they are possible candidates as bone substitute elements. © 2020 Elsevier Ltd and Techna Group S.r.l.Article Citation - WoS: 12Citation - Scopus: 17Fish Scale/Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) Nanofibrous Composite Scaffolds for Bone Regeneration(SAGE Publications, 2020) Kara, Aylin; Güneş, Oylum C.; Albayrak, Aylin Z.; Bilici, Gökçen; Erbil, Güven; Havitcioğlu, HasanThe aim of this study was to produce three-dimensional, nanofibrous fish scale/poly(3-hydroxybutyrate-co-3-hydroxyvalerate) composite scaffolds as bone filling materials. This is the first report wherein fish scales were used within a nanofibrous matrix for bone regeneration. Composite scaffolds with a cotton wool-like structure (fiber diameter: 560 +/- 64 nm; porosity: 82%) were obtained by incorporating chopped fish scales into wet-electrospun poly(3-hydroxybutyrate-co-3-hydroxyvalerate) nanofibers and freeze-drying. The addition of the fish scales improved the mechanical properties, biomineralization tendency, cell viability, alkaline phosphatase activity, and type I collagen production. Consequently, produced composite scaffolds would be regarded to have the therapeutic capacity in bone tissue damages.