PubMed İndeksli Yayınlar Koleksiyonu / PubMed Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7645
Browse
3 results
Search Results
Now showing 1 - 3 of 3
Article Citation - WoS: 8Citation - Scopus: 9Development of Plant-Based Biopolymer Coatings for 3d Cell Culture: Boron-Silica Quince Seed Mucilage Nanocomposites(Royal Society of Chemistry, 2023) Yılmaz, Hilal Deniz; Cengiz, Uğur; Derkuş, Burak; Arslan, Yavuz EmreSpheroid formation with spontaneous aggregation has captured interest in most cell culture studies due to its easy set-up and more reliable results. However, the economic and technical costs of the advanced systems and commercial ultra-low adhesive platforms have pushed researchers into pursuing alternatives. Nowadays, polymeric coatings, including poly-hydroxyethyl methacrylate and agar/agarose, are the commonly used polymers for non-adhesive plate fabrication, yet the costs and working solvent or heat-dependent preparation procedures maintain the need for the development of novel biomaterials. Here, we propose a greener and more economical approach for producing non-adherent surfaces and spheroid formation. For this, a plant waste-based biopolymer from quince fruit (Cydonia oblonga Miller, from Rosaceae family) seeds and boron-silica precursors were introduced. The unique water-holding capacity of quince seed mucilage (Q) was enriched with silanol and borate groups to form bioactive and hydrophilic nanocomposite overlays for spheroid studies. Moreover, 3D gel plates from the nanocomposite material were fabricated and tested in vitro as a proof-of-concept. The surface properties of coatings and the biochemical and mechanical properties of the nanocomposite materials were evaluated in-depth with techniques, and extra hydrophilic coatings were obtained. Three different cell lines were cultured on these nanocomposite surfaces, and spheroid formation with increased cellular viability was recorded on day 3 with a >200 & mu;m spheroid size. Overall, Q-based nanocomposites are believed to be a fantastic alternative for non-adherent surface fabrication due to their low-cost, easy operation, and intrinsic hydration layer forming capacity with biocompatible nature in vitro.Article Citation - WoS: 19Citation - Scopus: 20Transparent Pullulan/Mica Nanocomposite Coatings With Outstanding Oxygen Barrier Properties(MDPI Multidisciplinary Digital Publishing Institute, 2017) Uysal Ünalan, İlke; Boyacı, Derya; Trabattoni, Silvia; Tavazzi, Silvia; Farris, StefanoThis study presents a new bionanocomposite coating on poly(ethylene terephthalate) (PET) made of pullulan and synthetic mica. Mica nanolayers have a very high aspect ratio (α), at levels much greater than that of conventional exfoliated clay layers (e.g., montmorillonite). A very small amount of mica (0.02 wt %, which is φ ≈ 0.00008) in pullulan coatings dramatically improved the oxygen barrier performance of the nanocomposite films under dry conditions, however, this performance was partly lost as the environmental relative humidity (RH) increased. This outcome was explained in terms of the perturbation of the spatial ordering of mica sheets within the main pullulan phase, because of RH fluctuations. This was confirmed by modelling of the experimental oxygen transmission rate (OTR) data according to Cussler’s model. The presence of the synthetic nanobuilding block (NBB) led to a decrease in both static and kinetic coefficients of friction, compared with neat PET (≈12% and 23%, respectively) and PET coated with unloaded pullulan (≈26% reduction in both coefficients). In spite of the presence of the filler, all of the coating formulations did not significantly impair the overall optical properties of the final material, which exhibited haze values below 3% and transmittance above 85%. The only exception to this was represented by the formulation with the highest loading of mica (1.5 wt %, which is φ ≈ 0.01). These findings revealed, for the first time, the potential of the NBB mica to produce nanocomposite coatings in combination with biopolymers for the generation of new functional features, such as transparent high oxygen barrier materials.Article Citation - WoS: 33Citation - Scopus: 33Folic Acid Modified Clay/Polymer Nanocomposites for Selective Cell Adhesion(Royal Society of Chemistry, 2014) Barlas, Fırat Barış; Ağ Şeleci, Didem; Özkan, Melek; Demir, Bilal; Şeleci, Muharrem; Aydın, Muhammed; Taşdelen, M. A.; Zareie, Hadi M.; Timur, Suna; Özçelik, Serdar; Yağcı, YusufA folic acid (FA) modified poly(epsilon-caprolactone)/clay nanocomposite (PCL/MMT-(CH2CH2OH)2-FA) resulting in selective cell adhesion and proliferation was synthesized and characterized as a cell culture and biosensing platform. For this purpose, first the FA modified clay (MMT-(CH2CH2OH)2-FA) was prepared by treating the organo-modified clay, Cloisite 30B [MMT-(CH2CH 2OH)2] with FA in chloroform at 60°C. Subsequent ring opening polymerization of ε-caprolactone in the presence of tin octoate (Sn(Oct)2) using MMT-(CH2CH2OH)2-FA at 110°C resulted in the formation of MMT-(CH2CH 2OH)2-FA with an exfoliated clay structure. The structures of intermediates and the final nanocomposite were investigated in detail by FT-IR spectral analysis and DSC, TGA, XRD, SEM and AFM measurements. The combination of FA, PCL and clay provides a simple and versatile route to surfaces that allows controlled and selective cell adhesion and proliferation. FA receptor-positive HeLa and negative A549 cells were used to prove the selectivity of the modified surfaces. Both microscopy and electrochemical sensing techniques were applied to show the differences in cell adherence on the modified and pristine clay platforms. This approach is expected to be adapted into various bio-applications such as 'cell culture on chip', biosensors and design of tools for targeted diagnosis or therapy.