Food Engineering / Gıda Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/12
Browse
3 results
Search Results
Article Citation - WoS: 7Citation - Scopus: 9A Screen-Printed Electrode Modified With Gold Nanoparticles/ Cellulose Nanocrystals for Electrochemical Detection of 4,4'-methylene Diphenyl Diamine(Elsevier, 2023) Büyüktaş, Duygu; Ghaani, Masoud; Rovera, Cesare; Carullo, Daniele; Olsson, Richard T.; Korel, Figen; Farris, StefanoDeveloping simple, cost-effective, easy-to-use, and reliable analytical devices if of utmost importance for the food industry for rapid in-line checks of their products that must comply with the provisions set by the current legislation. The purpose of this study was to develop a new electrochemical sensor for the food packaging sector. More specifically, we propose a screen -printed electrode (SPE) modified with cellulose nanocrystals (CNCs) and gold nanoparticles (AuNPs) for the quantification of 4,4'-methylene diphenyl diamine (MDA), which is one of the most important PAAs that can transfer from food packaging materials into food stuffs. The electrochemical performance of the proposed sensor (AuNPs/CNCs/SPE) in the presence of 4,4'- MDA was evaluated using cyclic voltammetry (CV). The modified AuNPs/CNCs/SPE showed the highest sensitivity for 4,4'-MDA detection, with a peak current of 9.81 mu A compared with 7.08 mu A for the bare SPE. The highest sensitivity for 4,4'-MDA oxidation was observed at pH = 7, whereas the detection limit was found at 57 nM and the current response of 4,4'-MDA rose linearly as its concentration increased from 0.12 mu M to 100 mu M. Experiments using real packaging materials revealed that employing nanoparticles dramatically improved both the sensitivity and the selectivity of the sensor, which can be thus considered as a new analytical tool for quick, simple, and accurate measurement of 4,4 '-MDA during converting operations.Article Citation - WoS: 22Citation - Scopus: 27Layer-By Assembly of Lysozyme With Iota-Carrageenan and Gum Arabic for Surface Modification of Food Packaging Materials With Improved Barrier Properties(Elsevier, 2022) Koca, Nazan; Bayramoğlu, BesteThe study aimed to investigate the surface modification of biaxially oriented polypropylene (BOPP) by layer-by-layer (LbL) assembly of lysozyme (LZ) with two different polysaccharides, iota-carrageenan (IC) and gum arabic (GA), for food packaging applications. The effects of solution pH, adsorption time, elimination of intermediate drying steps were investigated. The LbL film growth was monitored up to 10 deposition steps by UV–Vis spectroscopy and in situ surface plasmon resonance (SPR). The most successful processing conditions for both types of coatings were pH 7–7 combination with intermediate drying and 20 min adsorption time. SPR pointed out a ‘dissolution/reconstruction’ mechanism in film formation. The thickness and surface morphology of the coatings were characterized by Atomic force microscopy (AFM). The surface roughnesses of LZ/IC coatings were higher than that of LZ/GA coatings indicating a denser matrix in the latter. Deposition of 5 bilayers of LZ/IC and LZ/GA on BOPP resulted in 66.15% and 56.89% reduction in oxygen transmission rate (OTR) of the film, respectively. The corresponding reductions in water vapor transmission rate (WVTR) were 28% and 33.52%, respectively. Elimination of intermediate drying steps resulted in less overall deposition, rougher surfaces, diminished oxygen and water barrier properties. The edible LbL coatings obtained in this study possess good gas barrier properties, which is very promising for their use in the preservation of fresh/fresh-cut produce in combination with modified atmosphere packaging applications. The results promise reduced use of plastic films in food packaging.Article Citation - WoS: 7Citation - Scopus: 6Development of a Nano-Modified Glassy Carbon Electrode for the Determination of 2,6-Diaminotoluene (tda)(Elsevier, 2021) Büyüktaş, Duygu; Ghaani, Masoud; Rovera, Cesare; Olsson, Richard T.; Korel, Figen; Farris, StefanoThe objective of this study was to improve the overall performance of a glassy carbon electrode (GCE) for the detection of 2,6-diaminotoluene (TDA), a possibly carcinogenic primary aromatic amines (PAAs) that poses a serious risk for the consumer' health because they can transfer from multilayer food packages including adhesives based on aromatic polyurethane (PU) systems, to the food. The modification of the electrode surface was made by means of multi-walled carbon nanotubes (MWCNTs) and mesopomus carbon nanoparticles (MCNs). The MWCNTs-MCNs/GCE allowed achieving the best performance in terms of sensitivity, as revealed by cyclic voltammetry - CV, with an oxidation peak of 20.95 mu A over 0.079 mu A of the bare GCE. The pH of the medium influenced the oxidation of 2,6-TDA, with highest sensitivity at pH similar to 7. Amperometry experiments led to an estimated detection limit of 0.129 mu M, and three linear ranges were obtained for 2,6-TDA: 0.53-11.37 mu M, 11.37-229.36 mu M, and 229.36-2326.60 mu M. Chronoamperometry experiments combined with Cottrell's theory allowed estimating a diffusion coefficient of 2,6-TDA of 1.34 x 10(-4) cm(2) s(-1). The number of electrons (n similar to 1) involved in the catalytic oxidation of 2,6-TDA was determined according to the Lavimn's theory. Real sample tests demonstrated that the modification of the sensor using nanoparticls allowed to obtain a highly sensitive and selective sensor, which can possibly used as an alternative analytical device for the rapid, easy, and reliable determination of 2,6-TDA.