Food Engineering / Gıda Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/12
Browse
Search Results
Conference Object Citation - Scopus: 2Preparation and Characterization of Hydroxyapatite/Calcium Phosphate Powders(Trans Tech Publications, 2004) Şimşek, Deniz; Çiftçioğlu, Rukiye; Harsa, ŞebnemThe preparation of calcium phosphate based powders through chemical precipitation in order to determine the optimum conditions for the preparation of stoichiometric, thermally stable hydroxyapatite (HA) powders was investigated in this work. The effects of parameters like pH, aging time, and heat treatment temperature on the phase structure and morphology of the powders were investigated by SEM and XRD.HA was prepared at a Ca/P ratio of 1.67. The precipitation pH had a profound influence on the morphology and crystallite size of the powders in the 4-11 pH range. Relatively large 5 mum prismatic particles were obtained at low pH whereas the powders were formed from agglomerates of nano sized particles at high pH. Powders had a HA dominant phase structure above a pH of 8. Phase pure HA powders were obtained with close to theoretical yields at pH = 10 and 11. The crystallite sizes of the powders varied from about 30 nm at 90degreesC to 50-90 mn at 1250degreesC with the smallest crystallite sizes obtained for pH 10 and 11 powders at 1250degreesC. The crystallite size increased significantly with aging temperature.Conference Object Citation - WoS: 8Citation - Scopus: 12Mechanical Properties of Hydroxyapatite Composites Reinforced With Hydroxyapatite Whiskers(Trans Tech Publications, 2004) Şimşek, Deniz; Çiftçioğlu, Rukiye; Güden, Mustafa; Çiftçioğlu, Muhsin; Harsa, Hayriye ŞebnemSintering and mechanical behavior of pure and hydroxyapatite (HA) whisker reinforced HA composites were investigated in this work. Pure and composite samples were prepared by using a commercial powder and whiskers prepared by molten salt synthesis. The dry-pressed samples were sintered in the 800 and 1300°C range. The effect of whisker-addition on the mechanical properties of HA was investigated through compression and hardness testing. Compressive strength and fracture strain were observed to increase by the addition of whiskers.Conference Object Citation - WoS: 10Citation - Scopus: 13Preparation and Characterization of Polylactide-Hydroxyapatite Biocomposites(Trans Tech Publications, 2004) Gültekin, Naz; Tıhmınlıoğlu, Funda; Çiftçioğlu, Rukiye; Çiftçioğlu, Muhsin; Harsa, Hayriye ŞebnemIn the present study, the preparation and characterization of polylactide-Hydroxyapatite(HA) composite films for biomedical applications have been studied. The effects of number of parameters such as polymer type, HA loading, surface modification and its concentration on the mechanical and microstructural properties of the composites were investigated. Poly-L-Lactide and 96/4 Poly(L-Lactide co D-Lactide) copolymer-HA composites containing 10-40 wt% HA particles have been prepared by solvent casting technique. The HA powder was synthesized by precipitation technique. Interfacial interactions between HA and polylactide polymer were modified to improve filler compatibility and mechanical properties of the composites by surface treatment of the HA with two different silane coupling agents; 3-aminopropyltriemoxysilane (AMPTES) and 3-mercaptopropyltrimethoxysilane (MPTMS) at three different concentrations(0.5-2 wt%). Silane treatment indicated improvements in the mechanical properties of the composites compared to the untreated HA loaded polylactide composites. Tensile test results showed that the maximum improvement in the mechanical properties of the composites was obtained for PLA composites containing 1 wt% aminofunctional silane treated HA and 0.5-wt% mercaptopropyltrimethoxy silane treated HA for PDLA composites. Scanning electron microscopy studies also revealed better dispersion of silane treated HA particles in the polymer matrix.