Photonics / Fotonik
Permanent URI for this collectionhttps://hdl.handle.net/11147/2590
Browse
40 results
Search Results
Article Citation - WoS: 3Citation - Scopus: 3Green Fabrication of Lanthanide-Doped Hydroxide-Based Phosphors: Y(oh)(3):eu3+ Nanoparticles for White Light Generation(Beilstein-Institut Zur Forderung der Chemischen Wissenschaften, 2019) Güner, Tuğrul; Kuş, Anılcan; Özcan, Mehmet; Genç, Aziz; Şahin, Hasan; Demir, Mustafa MuammerPhosphors can serve as color conversion layers to generate white light with varying optical features, including color rendering index (CRI), high correlated color temperature (CCT), and luminous efficacy. However, they are typically produced under harsh synthesis conditions such as high temperature, high pressure, and/or by employing a large amount of solvent. In this work, a facile, water-based, rapid method has been proposed to fabricate lanthanide-doped hydroxide-based phosphors. In this sense, sub-micrometer-sized Y(OH)(3):Eu3+ particles (as red phosphor) were synthesized in water at ambient conditions in <= 60 min reaction time. The doping ratio was controlled from 2.5-20 mol %. Additionally, first principle calculations were performed on Y(OH)(3):Eu3+ to understand the preferable doping scenario and its optoelectronic properties. As an application, these fabricated red phosphors were integrated into a PDMS/YAG:Ce3+ composite and used to generate white light. The resulting white light showed a remarkable improvement (approximate to 24%) in terms of luminous efficiency, a slight reduction of CCT (from 3900 to 3600 K), and an unchanged CRI (approximate to 60) as the amount of Y(OH)(3):Eu3+ was increased.Article Citation - WoS: 3Citation - Scopus: 4Experimental and First-Principles Investigation of Cr-Driven Color Change in Cesium Lead Halide Perovskites(American Institute of Physics, 2019) Özen, Sercan; Güner, Tuğrul; Topçu, Gökhan; Özcan, Mehmet; Demir, Mustafa Muammer; Şahin, HasanHerein, we report room temperature Cr-doping for all-inorganic perovskites that have attracted great attention in recent years due to their extraordinary optical properties, low cost, and ease of synthesis. Incorporation of Cr 3 + ions into the perovskite crystal lattices is achieved by following a facile route involving an antisolvent recrystallization method at room temperature. It is shown that both Cr-doping and formation of crystals in the CsPbBr x Cl 3 - x phase are provided by increasing the concentration of the CrCl 3 solution. It is also observed that the doping procedure leads to the emergence of three types of distinctive peaks in the PL spectrum originating from CsPbBr x Cl 3 - x domains (476-427nm), Cr-strained host lattices (515nm), and midgap states formed by Cr dopants (675-775nm). It is also found that the Cr-doped perovskites emitting a dark violaceous color change their color to white with a high color rendering index (88) in 30-day time intervals. Easy-tunable optical properties of all-inorganic Cs perovskites indicate their great potential for future optoelectronic device applications.Article Citation - WoS: 5Citation - Scopus: 6Contribution of O-2 Plasma Treatment and Amine Modified Gos on Film Properties of Conductive Pedot:pss: Application in Indium Tin Oxide Free Solution Processed Blue Oled(Elsevier, 2019) Diker, Halide; Yeşil, Fatih; Varlıklı, CananPrimary (n-propyl amine, n-PRYLA), secondary (dipropyl amine, DPRYLA) and alcohol (propanol amine, PRPOHA) amine derivatives were used as amine sources in graphene oxide (GO) modification and obtained samples were named as nPRYLA-GO, DPRYLA-GO and PRPOHA-GO, respectively. Modified graphene oxide (mGO) derivatives were doped in poly (3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PH1000) and O-2 plasma treatment (70W, 3 min) was applied on the spin casted films. PH1000:mGO films presented high optical transparency values (> 90%) and low resistivity (177-183 Q/sq). The roughness values were increased especially when the hydrophobic alkyl chain containing DPRYLA-GO and nPRYLA-GO were doped in PH1000. Prepared films were utilized as anode in solution processed blue organic light emitting diode. PH1000:PRPOHA-GO anode presented more than 30 nm of decrement in full with at half maximum and 1.6, 1.5 and 1.9 fold enhancements in current, power and external quantum efficiency values, compared to those of ITO anode, respectively.Article Citation - WoS: 24Citation - Scopus: 24Defect Tolerant and Dimension Dependent Ferromagnetism in Mnse2(Royal Society of Chemistry, 2019) Eren, İsmail; İyikanat, Fadıl; Şahin, HasanBy performing density functional theory-based calculations, we investigate the structural, vibrational, electronic and magnetic properties of 2D monolayers, nanoribbons and quantum dots of MnSe2. Vibrational spectrum analysis reveals the dynamical stability of not only ferromagnetic but also antiferromagnetic phases of single layer MnSe2 crystal structures. Electronically, calculations show that 1T-MnSe2 is a ferromagnetic structure displaying metallic behavior. It is also found that the structure preserves its dynamical stability and metallic behavior even under the presence of high density Se vacancies. Moreover, it was predicted that, differing from the 2D MnSe2, metal-metal interaction driven reconstructions result in ferromagnetic-to-antiferromagnetic crossover in the ground state of nanoribbons and quantum dots. With its robust ferromagnetic metallic character in the 2D ultra-thin limit and dimension-dependent magnetic properties, MnSe2 is an important candidate for spintronic device applications.Article Citation - WoS: 30Citation - Scopus: 29Stacking-Dependent Excitonic Properties of Bilayer Blue Phosphorene(American Physical Society, 2019) İyikanat, Fadıl; Torun, Engin; Senger, Ramazan Tuğrul; Şahin, HasanAb initio calculations in the framework of many-body perturbation theory (MBPT) are performed to calculate the electronic and optical properties of monolayer and bilayer blue phosphorene with different stacking configurations. It is found that the stacking configuration of bilayer blue phosphorene strongly affects the electronic band gap of the material. By solving the Bethe-Salpeter equation (BSE) on top of the G(0)W(0) calculation, the binding energies, spectral positions, and band decomposition of excitons of monolayer and bilayer configurations are investigated. The most prominent two excitonic peaks of bilayers are examined in detail. Our calculations show that different stacking configurations lead to distinct interlayer interaction characteristics which lead to substantial change in the optical spectrum of bilayer blue phosphorene. Mostly intralayer and mixed interlayer excitons with quite high binding energies are obtained in bilayer blue phosphorene. Our results show that excitonic properties of ultrathin materials play an important role in tuning and improving the optoelectronic performance of two-dimensional materials.Article Citation - WoS: 89Citation - Scopus: 85Cspbbr3 Perovskites: Theoretical and Experimental Investigation on Water-Assisted Transition From Nanowire Formation To Degradation(American Physical Society, 2018) Akbalı, Barış; Topçu, Gökhan; Güner, Tuğrul; Özcan, Mehmet; Demir, Mustafa Muammer; Şahin, HasanRecent advances in colloidal synthesis methods have led to an increased research focus on halide perovskites. Due to the highly ionic crystal structure of perovskite materials, a stability issue pops up, especially against polar solvents such as water. In this study, we investigate water-driven structural evolution of CsPbBr3 by performing experiments and state-of-the-art first-principles calculations. It is seen that while an optical image shows the gradual degradation of the yellowish CsPbBr3 structure under daylight, UV illumination reveals that the degradation of crystals takes place in two steps: transition from a blue-emitting to green-emitting structure and and then a transition from a green-emitting phase to complete degradation. We found that as-synthesized CsPbBr3 nanowires (NWs) emit blue light under a 254 nm UV source. Before the degradation, first, CsPbBr3 NWs undergo a water-driven structural transition to form large bundles. It is also seen that formation of such bundles provides longer-term environmental stability. In addition theoretical calculations revealed the strength of the interaction of water molecules with ligands and surfaces of CsPbBr3 and provide an atomistic-level explanation to a transition from ligand-covered NWs to bundle formation. Further interaction of green-light-emitting bundles with water causes complete degradation of CsPbBr3 and the photoluminescence signal is entirely quenched. Moreover, Raman and x-ray-diffraction measurements revealed that completely degraded regions are decomposed to PbBr2 and CsBr precursors. We believe that the findings of this study may provide further insight into the degradation mechanism of CsPbBr3 perovskite by water.Article Citation - WoS: 28Citation - Scopus: 28Enhanced Stability of Single-Layer W-Gallenene Through Hydrogenation(American Chemical Society, 2018) Badalov, S. V.; Yağmurcukardeş, Mehmet; Peeters, François M.; Şahin, HasanUsing density functional theory based first-principles calculations, the effect of surface hydrogenation on the structural, dynamical, electronic, and mechanical properties of monolayer washboard-gallenene (w-gallenene) is investigated. It is found that the dynamically stabilized strained monolayer of w-gallenene has a metallic nonmagnetic ground state. Both one-sided and two-sided hydrogenations of w-gallenene suppress its dynamical instability even when unstrained. Unlike one-sided hydrogenated monolayer w-gallenene (os-w-gallenene), two-sided hydrogenated monolayer w-gallenene (ts-w-gallenene) possesses the same crystal structure as w-gallenene. Electronic band structure calculations reveal that monolayers of hydrogenated derivatives of w-gallenene exhibit also metallic nonmagnetic ground state. Moreover, the linear-elastic constants, in-plane stiffness and Poisson ratio, are enhanced by hydrogenation, which is opposite to the behavior of other hydrogenated monolayer crystals. Furthermore, monolayer w-gallenene and ts-w-gallenene remain dynamically stable up to relatively higher biaxial strains as compared to borophene. With its enhanced dynamical stability, robust metallic character, and enhanced linear-elastic properties, hydrogenated monolayer w-gallenene is a potential candidate for nanodevice applications as a two-dimensional flexible metal.Article Citation - WoS: 30Citation - Scopus: 32Perylene-Embedded Electrospun Ps Fibers for White Light Generation(Elsevier Ltd., 2019) Güner, Tuğrul; Aksoy, Erkan; Demir, Mustafa Muammer; Varlıklı, CananPerylene dyes have been employed in the fabrication of white light due to their superior photophysical properties and relatively easy synthetic methods. However, their molecular aggregation in solid state is one of the main handicaps since it causes deviation in their optical properties and quenches photoluminescence quantum yields (Phi(f)). Investigation of the photophysical properties of a green (PTE), a yellow (PDI) and a new red (DiPhAPDI) emitting perylene derivative in solution, drop-casted films, polystyrene (PS) fibers and PS fibers embedded in poly (dimethyl siloxane) (PDMS) showed that PS:dye fibers prevent aggregation to some extend and allows high Of of dyes. The Of values of PTE, PDI and DiPhAPDI were all higher than 93.0% in solution and 84.8%, 94.3% and 73.6%, respectively in PS:dye fibers. Embedding the fibers in PDMS improved the photostabilities of the dyes two folds compared to their solution phases. The prepared dye containing fibers were combined together into a single PDMS film and utilized as a frequency conversion layer on a blue LED. Fabricated samples were found to show high color rendering index (>= 90), adjustable CCT (7500 K-5000 K), and power efficiency values exceeding 2001m/W depending on the used fiber amount in mass.Article Citation - WoS: 93Citation - Scopus: 95Single-Layer Janus-Type Platinum Dichalcogenides and Their Heterostructures(American Chemical Society, 2019) Kahraman, Zeynep; Kandemir, Ali; Yağmurcukardeş, Mehmet; Şahin, HasanUltrathin two-dimensional Janus-type platinum dichalcogenide crystals formed by two different atoms at opposite surfaces are investigated by performing state-of-the-art density functional theory calculations. First, it is shown that single-layer PtX2 structures (where X = S, Se, or Te) crystallize into the dynamically stable IT phase and are indirect band gap semiconductors. It is also found that the substitutional chalcogen doping in all PtX2 structures is favorable via replacement of surface atoms with a smaller chalcogen atom, and such a process leads to the formation of Janus-type platinum dichalcogenides (XPtY, where X and Y stand for S, Se, or Te) which are novel single-layer crystals. While all Janus structures are indirect band gap semiconductors as their binary analogues, their Raman spectra show distinctive features that stem from the broken out-of-plane symmetry. In addition, it is revealed that the construction of Janus crystals enhances the piezoelectric constants of PtX2 crystals significantly both in the in plane and in the out-of-plane directions. Moreover, it is shown that vertically stacked van der Waals heterostructures of binary and ternary (Janus) platinum dichalcogenides offer a wide range of electronic features by forming bilayer heterojunctions of type-I, type-II, and type-III, respectively. Our findings reveal that Janus-type ultrathin platinum dichalcogenide crystals are quite promising materials for optoelectronic device applications.Article Citation - WoS: 36Citation - Scopus: 34Raman Fingerprint of Stacking Order in Hfs2-Ca(oh)(2) Heterobilayer(American Physical Society, 2019) Yağmurcukardeş, Mehmet; Özen, Sercan; İyikanat, Fadıl; Peeters, François M.; Şahin, HasanUsing density functional theory-based first-principles calculations, we investigate the stacking order dependence of the electronic and vibrational properties of HfS2-Ca(OH)(2) heterobilayer structures. It is shown that while the different stacking types exhibit similar electronic and optical properties, they are distinguishable from each other in terms of their vibrational properties. Our findings on the vibrational properties are the following: (i) from the interlayer shear (SM) and layer breathing (LBM) modes we are able to deduce the AB' stacking order, (ii) in addition, the AB' stacking type can also be identified via the phonon softening of E-g(I) and A(g)(III) modes which harden in the other two stacking types, and (iii) importantly, the ultrahigh frequency regime possesses distinctive properties from which we can distinguish between all stacking types. Moreover, the differences in optical and vibrational properties of various stacking types are driven by two physical effects, induced biaxial strain on the layers and the layer-layer interaction. Our results reveal that with both the phonon frequencies and corresponding activities, the Raman spectrum possesses distinctive properties for monitoring the stacking type in novel vertical heterostructures constructed by alkaline-earth-metal hydroxides.