Mechanical Engineering / Makina Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4129
Browse
Search Results
Article Citation - WoS: 3Citation - Scopus: 3Determination of Activation Energy for Carbon/Epoxy Prepregs Containing Carbon Nanotubes by Differential Scanning Calorimetry(SAGE Publications, 2022) Uz, Yusuf Can; Tanoğlu, MetinThe aim of the present study is the thermal characterization of laboratory-scale carbon fiber/epoxy-based prepregs by incorporating single-wall carbon nanotubes (SWCNTs). Investigation of the cure behavior of a prepreg system is crucial for the characterization and optimization of the fiber reinforced polymeric (FRP) composite. To affect dispersion characteristics, SWCNTs were functionalized by oxidizing their surface with carboxyl (-COOH) group using an acid treatment. The modified resin system contained 0.05, 0.1, and 0.2 wt. % functionalized SWCNTs (F-SWCNTs). Carbon fiber (CF) reinforced prepregs containing various amount of F-SWCNTs were prepared using drum-type winding technique. FTIR was performed to identify new bonding groups formed after the functionalization of SWCNTs. Cure kinetics of prepregs prepared with/without F-SWCNTs were investigated using isoconversional methods.Article Citation - WoS: 7Citation - Scopus: 10The Computational Approach To Predicting Wear: Comparison of Wear Performance of Cfr-Peek and Xlpe Liners in Total Hip Replacement(Taylor & Francis, 2022) Alpkaya, Alican Tuncay; Mihçin, ŞenayWear on articulating bearing surfaces is a key factor causing revision in total hip replacement (THR). Wear debris that releases particles from bearing surfaces might result in adverse soft tissue reactions requiring revision surgeries. In this study, a comprehensive computational wear model based on the Archard wear equation was performed to investigate the wear performance under a three-dimensional (3D) physiological gait cycle, mimicking a normal walking condition (5 million cycles). The study shows that the accuracy of the model is highly dependent on the mesh convergence, the wear fraction, and the scaling factor. The simulations were run to provide a vast amount of detail for the reproducibility of the work. Cobalt chromium (CoCr) on cross-linked polyethylene (XLPE) and CoCr on carbon-fiber-reinforced polyether ether ketone (CFR-PEEK) prototype models were created in silico. The volumetric wear rates for CoCr-on-XLPE were calculated as 0.2989 (Formula presented.) for CoCr head and 21.0271 (Formula presented.) for XLPE liner, while for CoCr-on-CFR-PEEK they were 0.3484 (Formula presented.) for CoCr head and 1.8476 (Formula presented.) for CFR-PEEK liner. When compared to in vivo and in vitro studies, the wear patterns of these two prototypes are consistent with those of the conventional polyethylene liners in the literature. Although the volumetric wear rate of the CFR-PEEK liner is about 11 times lower than the counterpart of XLPE in MoP implants, the wear rate of CoCr was higher when compared to its use with XLPE. Therefore, CFR-PEEK articulating against orthopa\edic metals may not be as good an alternative as XLPE, due to higher indicative metallic wear. This detailed computational wear modeling methodology could be utilized in design improvements of implants.Article Citation - WoS: 1Citation - Scopus: 1Design of Demountable Reciprocal Frames With New Geometric Properties(Int. Association for Shell and Spatial Structures, 2022) Özen, Gülçin; Kiper, Gökhan; Korkmaz, KorayThis study aims to develop missing geometric knowledge for demountable reciprocal frames (RF). While designing a demountable RF, one should know the initial, in-process and final form of the RF. These processes require some specific geometric knowledge. There are some deficiencies about geometric properties in the previous studies about demountable RFs. In this study, the positions and the orientations of the nexors are found by using the Denavit-Hartenberg parameters. This information gives where the joints are placed, how they are oriented and take position according to one another. Besides, the influence of engagement length on the fan height and the base edge are analyzed. Thereby one will be able to find out how much space the RF covers with the known base edge. With the geometric knowledge obtained from this study, demountable RFs having different engagement lengths can be produced with the same nexors.Article A Novel Design Method of Deployable Semi-Regular Tessellated Surfaces With Plano-Spherical Units(Int. Association for Shell and Spatial Structures, 2022) Maral, Mesude Oraj; Korkmaz, Koray; Kiper, GökhanThe design of movable systems gives an opportunity to create transformable designs which respond to the environmental, functional, cultural, and aesthetical needs of today's architecture. This paper proposes a method for designing a family of deployable structures which can be applied to semi-regular tessellated planar surfaces such as roofs, walls, and shading devices. The generated modular approach and adaptability provides a wide usage area and various combinations for these designs. The regular convex polygon modules are designed as a network of the triangular units. The triangular unit is designed using Bennett's overconstrained plano-spherical linkage topology. The polygonal modules are assembled to each other in one-uniform semi-regular tessellations. The assembly of adjacent regular convex polygons in each tessellation is examined to find a proper solution for no collision during deployment and to properly fit a surface without any gaps or overlaps in the deployed position. The assembly method for creating 1-DoF deployable surfaces and mobility calculations for a unit, the polygonal modules, and the assemblies are computed, and motion studies are demonstrated with CAD models and exemplified for a square module for motion tests in a prototype.Article Citation - WoS: 22Citation - Scopus: 22Simultaneous Validation of Wearable Motion Capture System for Lower Body Applications: Over Single Plane Range of Motion (rom) and Gait Activities(Walter de Gruyter GmbH, 2022) Mihçin, ŞenayExtracting data from {Zhu, 2019 #5} daily life activities is important in biomechanical applications to define exact boundary conditions for the intended use-based applications. Although optoelectronic camera-marker based systems are used as gold standard tools for medical applications, due to line-of-sight problem, there is a need for wearable, affordable motion capture (MOCAP) systems. We investigate the potential use of a wearable inertial measurement unit (IMU) based-wearable MOCAP system for biomechanical applications. The in vitro proof of concept is provided for the full lower body consisting of hip, knee, and ankle joints via controlled single-plane anatomical range of motion (ROM) simulations using an electrical motor, while collecting data simultaneously via opto-electronic markers and IMU sensors. On 15 healthy volunteers the flexion-extension, abduction-Adduction, internal-external rotation (ROM) values of hip and, the flexion-extension ROM values of the knee and ankle joints are calculated for both systems. The Bland-Altman graphs showed promising agreement both for in vitro and in vivo experiments. The maximum Root Mean Square Errors (RMSE) between the systems in vitro was 3.4° for hip and 5.9° for knee flexion motion in vivo, respectively. The gait data of the volunteers were assessed between the heel strike and toe off events to investigate the limits of agreement, calculating the population averages and standard deviation for both systems over the gait cycle. The maximum difference was for the ankle joint <6°. The results show that proposed system could be an option as an affordable-democratic solution.