Mechanical Engineering / Makina Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4129
Browse
31 results
Search Results
Book Part Citation - WoS: 1Citation - Scopus: 1A Historical Review of Polyhedral Linkages(Springer, 2024) Kiper, GökhanPolyhedral linkages are linkages that resemble polyhedral shapes at different configurations. This paper summarizes the necessary geometrical fundamentals of polyhedral geometry and presents a historical and critical review of the polyhedral linkage designs available in the literature. Basic definitions of polyhedral geometry and operations are needed to comprehend and design polyhedral linkages. First, early works on polyhedral linkages are presented, where flexible polyhedra with rigid faces and flexible edges are issued. The final part is reserved to conformal polyhedral linkages, which go through shape transformations while plane, dihedral and solid angles are preserved. Conformal polyhedral linkages are examined in four categories: 1) Jitterbug-like linkages with screwing polygonal links connected to each other with dihedral angle preserving links, 2) polyhedral linkages with planar kinematic chains in radial motion planes, 3) polyhedral linkages with planar kinematic chains on faces, that are connected to each other with dihedral angle preserving links, and 4) other conformal polyhedral linkages. © The Author(s), under exclusive license to Springer Nature Switzerland AG 2024.Article Citation - WoS: 10Citation - Scopus: 10Stiffness Modeling of a 2-Dof Over-Constrained Planar Parallel Mechanism(Elsevier, 2023) Görgülü, İbrahimcan; Dede, Mehmet İsmet Can; Kiper, GökhanStiffness model acquisition of over-constrained parallel mechanisms is relatively difficult since they have more than necessary kinematic loops. In this study, a stiffness modeling solution for over-constrained parallel mechanisms is proposed while considering the computational cost efficiency. Three contributions of the paper are: (1) Presenting the stiffness modeling procedure for serially connected closed-loop structures by using the Virtual Joint Method (2) Considering the effect of dynamic auxiliary forces and dynamic external forces on the mobile platform's deflection and achieving a direct solution by using superposition principle (3) A model fitting procedure for modifying the stiffness coefficients to comply with the experimental data. A 2 degrees-of-freedom over-constrained parallel mechanism is investigated as a case study. However, the proposed stiffness model is 6-DoF since compliant deflections occur in any direction. A finite element analysis and an experimental study verify the model's results.Article Citation - WoS: 1Citation - Scopus: 1Design of Demountable Reciprocal Frames With New Geometric Properties(Int. Association for Shell and Spatial Structures, 2022) Özen, Gülçin; Kiper, Gökhan; Korkmaz, KorayThis study aims to develop missing geometric knowledge for demountable reciprocal frames (RF). While designing a demountable RF, one should know the initial, in-process and final form of the RF. These processes require some specific geometric knowledge. There are some deficiencies about geometric properties in the previous studies about demountable RFs. In this study, the positions and the orientations of the nexors are found by using the Denavit-Hartenberg parameters. This information gives where the joints are placed, how they are oriented and take position according to one another. Besides, the influence of engagement length on the fan height and the base edge are analyzed. Thereby one will be able to find out how much space the RF covers with the known base edge. With the geometric knowledge obtained from this study, demountable RFs having different engagement lengths can be produced with the same nexors.Article A Novel Design Method of Deployable Semi-Regular Tessellated Surfaces With Plano-Spherical Units(Int. Association for Shell and Spatial Structures, 2022) Maral, Mesude Oraj; Korkmaz, Koray; Kiper, GökhanThe design of movable systems gives an opportunity to create transformable designs which respond to the environmental, functional, cultural, and aesthetical needs of today's architecture. This paper proposes a method for designing a family of deployable structures which can be applied to semi-regular tessellated planar surfaces such as roofs, walls, and shading devices. The generated modular approach and adaptability provides a wide usage area and various combinations for these designs. The regular convex polygon modules are designed as a network of the triangular units. The triangular unit is designed using Bennett's overconstrained plano-spherical linkage topology. The polygonal modules are assembled to each other in one-uniform semi-regular tessellations. The assembly of adjacent regular convex polygons in each tessellation is examined to find a proper solution for no collision during deployment and to properly fit a surface without any gaps or overlaps in the deployed position. The assembly method for creating 1-DoF deployable surfaces and mobility calculations for a unit, the polygonal modules, and the assemblies are computed, and motion studies are demonstrated with CAD models and exemplified for a square module for motion tests in a prototype.Article Citation - WoS: 7Citation - Scopus: 7Gravity Compensation of a 2r1t Mechanism With Remote Center of Motion for Minimally Invasive Transnasal Surgery Applications [article](Cambridge University Press, 2023) Aldanmaz, Ataol Behram; Ayit, Orhan; Kiper, Gökhan; Dede, Mehmet İsmet CanThis work addresses the gravity balancing of a 2R1T (2 rotations – 1 translation) mechanism with remote center of motion. A previously developed balancing solution is modified and applied to a prototype and test results are presented. The mechanism is an endoscope holder for minimally invasive transnasal pituitary gland surgery. In this surgery, the endoscope is inserted through a nostril of the patient through a natural path to the pituitary gland. During the surgery, it is vital for the manipulator to be statically balanced so that in case of a motor failure, the patient is protected against any harmful motion of the endoscope. Additionally, static balancing takes the gravitational load from the actuators and hence facilitates the control of the mechanism. The mechanism is a 2URRR-URR type parallel manipulator with three legs. The payload mass is distributed to the legs on the sides. By using counter-masses for two links of each leg, the center of mass of each leg is lumped on the proximal link which simplifies the problem to balancing of a two degree-of-freedom inverted pendulum. The two proximal links with the lumped mass are statically balanced via springs. Dynamic simulations indicate that when the mechanism is statically balanced, generated actuator torques are reduced by 93.5%. Finally, the balancing solution is implemented on the prototype of the manipulator. The tests indicate that the manipulator is statically balanced within its task space when the actuators are disconnected. When the actuators are connected, the torque requirements decrease by about 37.8% with balancing.Article Citation - WoS: 5Citation - Scopus: 5Loop Based Classification of Planar Scissor Linkages(Springer, 2022) Kiper, Gökhan; Korkmaz, Koray; Gür, Şebnem; Yar Uncu, Müjde; Maden, Feray; Akgün, Yenal; Karagöz, CevahirScissor linkages have been used for several applications since ancient Greeks and Romans. In addition to simple scissor linkages with straight rods, linkages with angulated elements have been introduced in the last decades. In the related literature, two methods have been used to design scissor linkages, one of which is based on scissor elements, and the other is based on assembling loops. This study presents a systematic classification of scissor linkages as assemblies of rhombus, kite, dart, parallelogram and anti-parallelogram loops using frieze patterns and long-short diagonal connections. After the loops are replicated along a curve as a pattern, the linkages are obtained by selection of proper common link sections for adjacent loops. The resulting linkages are analyzed for their motions and they are classified as realizing scaling deployable, angular deployable or transformable motion. Some of the linkages obtained are novel. Totally 10 scalable deployable, 1 angular deployable and 8 transformable scissor linkages are listed. Designers in architecture and engineering can use this list of linkages as a library of scissor linkage topologies.Article Design, Prototyping and Tests of a Rollable Ramp for Temporary Use(Springer, 2021) Doğan Kumtepe, Elvan; Kiper, GökhanPortable ramps, used generally by wheelchair users, offer temporary solution to increase accessibility and mobility. Preferably these ramps should be compact and lightweight for ease of handling and storage. Different types of portable ramps in the market that are used by wheelchair users are generally made of aluminum and require several improvements, especially in terms of lightweight and compactness. Based on wheelchair users’ inclinations a compact and lightweight rollable ramp is designed in this study. A parametric model of the links of the ramp are derived and the rolled geometry is optimized using convex hull and smallest enclosing circle algorithms. The side bars of the links are designed and manufactured from aluminum and the load-bearing panels are manufactured from sandwich composite structures with honeycomb core. Strength calculations are performed analytically and also with finite-element analysis. After the design is finalized, a prototype is manufactured. The designed ramp is 15.4% more compact and has 18.9% less weight compared to the best rival product available in the market. Load tests and functional tests are performed with voluntary wheelchair users. Several positive feedbacks are received from the participants about the ramp being practical, easy to use and store, lightweight, advantage of the anti-slip surface.Conference Object A sustainable association case study: IFToMM member organization Turkey(Springer, 2022) Kiper, Gökhan; Söylemez, EresAs a member of IFToMM founded in 2011, Turkish Machine Theory Association’s (MakTeD) structure has put special emphasis on sustainability of the association and initiated several activities for improving the quality of education and research in mechanism and machine science area, hence supporting the SDG4 Quality Education of the UN. This paper presents the activities and methodologies of MakTeD. The paper starts with a brief history of mechanism and machine science in Turkey. In 10 years MakTeD organized 4 symposiums, 1 conference, 4 summer/winter schools, 8 workshops and hosted an IFToMM Executive Council meeting. Each chapter of the biyearly held National Symposium on Theory of Machines is held by a different university and especially newly established and the universities in relatively smaller cities are prioritized in order to promote those universities and to contribute to development of these universities. Especially the summer/winter schools and workshops have a widespread impact on mechanism and machine science education and research at the universities and institutions. MakTeD also contributes to the community with published books and support programs for young researchers.Article Citation - WoS: 6Citation - Scopus: 7Human-Robot Interfaces of the Neuroboscope: a Minimally Invasive Endoscopic Pituitary Tumor Surgery Robotic Assistance System(ASME, 2021) Dede, Mehmet İsmet Can; Kiper, Gökhan; Ayav, Tolga; Özdemirel, Barbaros; Tatlıcıoğlu, Enver; Hanalioğlu, Şahin; Işıkay, İlkayEndoscopic endonasal surgery is a commonly practiced minimally invasive neurosurgical operation for the treatment of a wide range of skull base pathologies including pituitary tumors. A common shortcoming of this surgery is the necessity of a third hand when the endoscope has to be handled to allow active use of both hands of the main surgeon. The robot surgery assistant NeuRoboScope system has been developed to take over the endoscope from the main surgeon's hand while providing the surgeon with the necessary means of controlling the location and direction of the endoscope. One of the main novelties of the NeuRoboScope system is its human-robot interface designs which regulate and facilitate the interaction between the surgeon and the robot assistant. The human-robot interaction design of the NeuRoboScope system is investigated in two domains: direct physical interaction (DPI) and master-slave teleoperation (MST). The user study indicating the learning curve and ease of use of the MST is given and this paper is concluded via providing the reader with an outlook of possible new human-robot interfaces for the robot assisted surgery systems.Other Corrigendum To “kinematic Design of a Non-Parasitic 2r1t Parallel Mechanism With Remote Center of Motion To Be Used in Minimally Invasive Surgery Applications” [mechanism and Machine Theory 153 (2020) 104013] (mechanism and Machine Theory (2020) 153, (s0094114x20302342), (10.1016/J.mechmachtheory.2020.104013))(Elsevier, 2021) Yaşır, Abdullah; Kiper, Gökhan; Dede, Mehmet İsmet CanThe authors regret that one of the affiliation information for Gökhan Kiper is wrong. Dr. Kiper is not affiliated to Delft University of Technology. Dr. Kiper is affiliated to İzmir Institute of Technology. The data administrators of Elsevier and the corresponding author would like to apologise for any inconvenience caused. © 2021 International Federation for the Promotion of Mechanism and Machine Science