Mechanical Engineering / Makina Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4129
Browse
9 results
Search Results
Now showing 1 - 9 of 9
Article Citation - WoS: 22Citation - Scopus: 22Simultaneous Validation of Wearable Motion Capture System for Lower Body Applications: Over Single Plane Range of Motion (rom) and Gait Activities(Walter de Gruyter GmbH, 2022) Mihçin, ŞenayExtracting data from {Zhu, 2019 #5} daily life activities is important in biomechanical applications to define exact boundary conditions for the intended use-based applications. Although optoelectronic camera-marker based systems are used as gold standard tools for medical applications, due to line-of-sight problem, there is a need for wearable, affordable motion capture (MOCAP) systems. We investigate the potential use of a wearable inertial measurement unit (IMU) based-wearable MOCAP system for biomechanical applications. The in vitro proof of concept is provided for the full lower body consisting of hip, knee, and ankle joints via controlled single-plane anatomical range of motion (ROM) simulations using an electrical motor, while collecting data simultaneously via opto-electronic markers and IMU sensors. On 15 healthy volunteers the flexion-extension, abduction-Adduction, internal-external rotation (ROM) values of hip and, the flexion-extension ROM values of the knee and ankle joints are calculated for both systems. The Bland-Altman graphs showed promising agreement both for in vitro and in vivo experiments. The maximum Root Mean Square Errors (RMSE) between the systems in vitro was 3.4° for hip and 5.9° for knee flexion motion in vivo, respectively. The gait data of the volunteers were assessed between the heel strike and toe off events to investigate the limits of agreement, calculating the population averages and standard deviation for both systems over the gait cycle. The maximum difference was for the ankle joint <6°. The results show that proposed system could be an option as an affordable-democratic solution.Article Citation - WoS: 4Citation - Scopus: 5Effects of Tib2 Nanoparticle Content on the Microstructure and Mechanical Properties of Aluminum Matrix Nanocomposites(Walter de Gruyter GmbH, 2017) Kandemir, SinanThe present work reports the fabrication of A357 alloy matrix nanocomposites reinforced with 0.5, 1.0 and 2.0 wt.-% TiB2 nanoparticles (20-30 nm) by a novel method which is the combination of semi-solid mechanical mixing and ultrasonic dispersion of nanoparticles in liquid state. The microstructural and mechanical properties of the fabricated nanocomposites were investigated. The microstructural studies conducted with optical and advanced electron microscopes indicated that reasonably effective deagglomeration and uniform distribution of TiB2 nanoparticles into the matrix were achieved. Transmission electron microscopy studies also confirmed that the nanoparticles were embedded into the matrix and a good bonding was obtained between the matrix and the reinforcement. Increasing nanoparticle content led to grain refinement and significant enhancement in the mechanical properties of nanocomposites. The addition of 0.5, 1.0, and 2.0 wt.-% TiB2 nanoparticles increased the 0.2 % proof stress of matrix alloy by approximately 31, 48 and 61 %, respectively. The contribution of different mechanisms to the strength enhancement is discussed. It is proposed that the strengthening is mainly due to Orowan mechanism and dislocation generation effect by the coefficient of thermal expansion mismatch between the TiB2 nanoparticles and the matrix.Article Citation - WoS: 16Citation - Scopus: 24Developing Polymer Composite-Based Leaf Spring Systems for Automotive Industry(Walter de Gruyter GmbH, 2018) Öztoprak, Nahit; Güneş, Mehmet Deniz; Tanoğlu, Metin; Aktaş, Engin; Eğilmez, Oğuz Özgür; Şenocak, Çiler; Kulaç, GedizComposite-based mono-leaf spring systems were designed and manufactured to replace existing mono-leaf metal leaf spring in a light commercial vehicle. In this study, experimentally obtained mechanical properties of different fiber-reinforced polymer materials are presented first, followed by the description of the finite element analytical model created in Abaqus 6.12-1 (Dassault Systemes Simulia Corp., RI, US) using the obtained properties. The results from the finite element analysis are presented next and compared with actual size experimental tests conducted on manufactured prototypes. The results demonstrated that the reinforcement type and orientation dramatically influenced the spring rate. The prototypes showed significant weight reduction of about 80% with improved mechanical properties. The hybrid composite systems can be utilized for composite-based leaf springs with considerable mechanical performance.Article Citation - WoS: 1Citation - Scopus: 2Off-Design Analysis of Transonic Bypass Fan Systems Using Streamline Curvature Through-Flow Method(Walter de Gruyter GmbH, 2019) Acarer, Sercan; Özkol, ÜnverThe two-dimensional streamline curvature through-flow modeling of turbomachinery is still a key element for turbomachinery preliminary analysis. Basically, axisymmetric swirling flow field is solved numerically. The effects of blades are imposed as sources of swirl, work input/output and entropy generation. Although the topic is studied vastly in the literature for compressors and turbines, combined modeling of the transonic fan and the downstream splitter of turbofan engine configuration, to the authors' best knowledge, is limited. In a prior study, the authors presented a new method for bypass fan modeling for inverse design calculations. Moreover, new set of practical empirical correlations are calibrated and validated. This paper is an extension of this study to rapid off-design analysis of transonic by-pass fan systems. The methodology is validated by two test cases: NASA 2-stage fan and GE-NASA bypass fan case. The proposed methodology is a simple extension for streamline curvature method and can be applied to existing compressor methodologies with minimum numerical effort.Book Part Scissor Linkages in the Design of Adaptive Morphologies(Walter de Gruyter GmbH, 2019) Akgün, Yenal; Maden, Feray; Gür, Şebnem; Kiper, Gökhan; Korkmaz, Koray; Aktaş, Engin; Yar Uncu, MüjdeScissor linkages are capable of forming various expandable structures. Architects can benefit from this type of linkage especially for designing adaptive, movable, transformable shell structures and deployable beam-like structures. Product designers may benefit as well. The two different methods described here convey the basic design approaches. The unit-based method is very effective for obtaining primary geometries like a dome, arch, circle or line, using serial multiplications and arrays of one of the scissor unit types presented here. The loop assembly method is more convenient when a final form, be it straight or free-form, is the main point of departure. In this case, unlike in the unit-based method, it is not necessary to opt for a specific scissor unit type and its dimensional constraints from the beginning. Designers can choose a type and number of loops and then define the scissor units following the loop sides. Since deployability is guaranteed by applying this method, the architect is free to choose the loop type most suitable for the functional needs and aesthetic concerns of the specific design. With the loop assembly method all loop alternatives can be assembled to scissor structures, their possible motions can be tested and evaluated in a short time, whereas the unit-based method is limited to a single type of motion that a specific unit can provide.Article Citation - WoS: 2Citation - Scopus: 2Staphylococcus Epidermidis Adhesion on Surface-Treated Open-Cell Ti6al4v Foams(Walter de Gruyter GmbH, 2016) Türkan, Uğur; Güden, Mustafa; Sudağıdan, MertThe effect of alkali and nitric acid surface treatments on the adhesion of Staphylococcus epidermidis to the surface of 60% porous open-cell Ti6Al4V foam was investigated. The resultant surface roughness of foam particles was determined from the ground flat surfaces of thin foam specimens. Alkali treatment formed a porous, rough Na2Ti5O11 surface layer on Ti6Al4V particles, while nitric acid treatment increased the number of undulations on foam flat and particle surfaces, leading to the development of finer surface topographical features. Both surface treatments increased the nanometric-scale surface roughness of particles and the number of bacteria adhering to the surface, while the adhesion was found to be significantly higher in alkali-treated foam sample. The significant increase in the number of bacterial attachment on the alkali-treated sample was attributed to the formation of a highly porous and nanorough Na2Ti5O11 surface layer.Article Citation - WoS: 4Citation - Scopus: 4A Pore Scale Study on Fluid Flow Through Two Dimensional Dual Scale Porous Media With Small Number of Intraparticle Pores(Walter de Gruyter GmbH, 2016) Sabet, Safa; Mobedi, Moghtada; Özgümüş, TürkülerIn the present study, the fluid flow in a periodic, non-isotropic dual scale porous media consisting of permeable square rods in inline arrangement is analyzed to determine permeability, numerically. The continuity and Navier-Stokes equations are solved to obtain the velocity and pressure distributions in the unit structures of the dual scale porous media for flows within Darcy region. Based on the obtained results, the intrinsic inter and intraparticle permeabilities and the bulk permeability tensor of the dual scale porous media are obtained for different values of inter and intraparticle porosities. The study is performed for interparticle porosities between 0.4 and 0.75 and for intraparticle porosities from 0.2 to 0.8. A correlation based on Kozeny-Carman relationship in terms of inter and intraparticle porosities and permeabilities is proposed to determine the bulk permeability tensor of the dual scale porous media.Article Citation - WoS: 3Citation - Scopus: 3Constructal vascularized structures(Walter de Gruyter GmbH, 2015) Çetkin, ErdalSmart features such as self-healing and selfcooling require bathing the entire volume with a coolant or/and healing agent. Bathing the entire volume is an example of point to area (or volume) flows. Point to area flows cover all the distributing and collecting kinds of flows, i.e. inhaling and exhaling, mining, river deltas, energy distribution, distribution of products on the landscape and so on. The flow resistances of a point to area flow can be decreased by changing the design with the guidance of the constructal law, which is the law of the design evolution in time. In this paper, how the flow resistances (heat, fluid and stress) can be decreased by using the constructal law is shown with examples. First, the validity of two assumptions is surveyed: using temperature independent Hess-Murray rule and using constant diameter ducts where the duct discharges fluid along its edge. Then, point to area types of flows are explained by illustrating the results of two examples: fluid networks and heating an area. Last, how the structures should be vascularized for cooling and mechanical strength is documented. This paper shows that flow resistances can be decreased by morphing the shape freely without any restrictions or generic algorithms.Article Citation - WoS: 4Citation - Scopus: 4Effects of Catalyst Precursor Type and Preparation Conditions, and Solvent Type on Activity and Selectivity of Pt/Sio2 Catalyst in Citral Hydrogenation(Walter de Gruyter GmbH, 2011) Depboylu, Can Okan; Yılmaz, Selahattin; Akkurt, SedatIn this study, citral hydrogenation reaction in liquid phase over silica gel supported Pt catalysts was investigated. It was desired to hydrogenate carbonyl group selectively to produce valuable unsaturated alcohols, namely geraniol and nerol. Pt/SiO2 catalysts were prepared by impregnation method. The effects of parameters investigated in the present study included Pt precursor type (hexachloroplatinic acid (HCLPA), platinum II acetylacetonate (PAA)), catalyst activation temperature (350°C and 450°C), catalyst activation without calcination, catalyst washing with 0.1 M NaOH and solvent type (ethanol, 2-pentanol). The catalysts activities and selectivities were affected by the type of precursor and activation temperature. The maximum citral conversion (89.50 percent) was achieved at lower activation temperature (350°C) with PAA precursor based catalyst. It was observed that higher activation temperature provided lower citral conversion but higher selectivity to unsaturated alcohols; increasing the activation temperature to 450°C decreased citral conversion to 26.10 percent. But selectivity to unsaturated alcohols, geraniol and nerol, increased from 7.06 to 54.60 percent. Catalyst washing and 2-pentanol prevented acetal formation. Catalyst activation without calcination gave lower citral conversion (20.84 percent) and selectivity to unsaturated alcohols (30.00 percent). Copyright © 2011 The Berkeley Electronic Press. All rights reserved.