Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
3 results
Search Results
Article Citation - WoS: 25Citation - Scopus: 26Lowering the Sintering Temperature of Solid Oxide Fuel Cell Electrolytes by Infiltration(Elsevier Ltd., 2019) Sındıraç, Can; Çakırlar, Seda; Büyükaksoy, Aligül; Akkurt, SedatA dense electrolyte with a relative density of over 95% is vital to prevent gas leakage and thus the achievement of high open circuit voltage in solid oxide fuel cells (SOFCs). The densification process of ceria based electrolyte requires high temperatures heat treatment (i.e. 1400-1500 degrees C). Thus, the minimum co-sintering temperatures of the anode-electrode bilayers are fixed at these values, resulting in coarse anode microstructures and consequently poor performance. The main purpose of this study is to densify gadolinia doped ceria (GDC), a common SOFC electrolyte, at temperatures lower than 1400 degrees C. By this aim, an approach involving the infiltration of polymeric precursors into porous electrolyte scaffolds, a method commonly used for composite SOFC electrodes, is proposed. By infiltrating polymeric precursors of GDC into porous GDC scaffolds, a reduction in the sintering temperature by at least 200 degrees C is achieved with no additives that might affect the electrical properties. Energy dispersive x-ray spectroscopy line scan analyses performed on porous GDC scaffolds infiltrated by a marker solution (polymeric FeOx precursor in this case) reveals a homogeneous infiltrated phase distribution, demonstrating the effectiveness of polymeric precursors.Article Citation - WoS: 19Citation - Scopus: 23Influence of Microstructure on the Rheological Behavior of Dense Particle Gels(John Wiley and Sons Inc., 2005) Wyss, Hans M.; Deliormanlı, Aylin M.; Tervoort, Elena V.; Gauckler, Ludwig JuliusRheological measurements are performed on highly concentrated alumina gels. By using an in situ mechanism based on enzyme-catalyzed internal reactions, we are able to form gels of highly concentrated particles without disturbing the microstructures that develop during the gelation process. These gels are produced by two different destabilization mechanisms: Either the pH of the suspension is shifted toward the isoelectric point (ΔpH method) or the ionic strength of the suspension is increased at a constant pH (ΔI method). The two destabilization mechanisms lead to gels of significantly different microstructures. We find notable differences in the rheological behavior of the two systems, suggesting a bond-bending mechanism for stress transmission in the case of ΔpH gels and a bond-stretching mechanism in the case of ΔI gels. In addition, for both kinds of gels we compare the in situ properties to those obtained after altering the microstructure by shearing. Results suggest an increase in elastic and yield properties of concentrated particle gels with decreasing homogeneity of their microstructures.Conference Object Citation - Scopus: 1Microstructural Characterization of Industrial Chromite and Spinel Cement Kiln Refractories With Emphasis on the Iron-Rich Rims(Trans Tech Publications, 2004) Mercanköşk, Y.; Akkurt, Sedat; Çiftçioğlu, MuhsinMagnesia-chromite (MgO + MgO·Cr2O3) and magnesia-spinel (MgO + MgO·Al2O3) refractory bricks that are used in the high temperature zones of rotary cement kilns are investigated for their microstructural characteristics. Their microstructures are important because the size, shape and distribution of periclase grains, chromites and the quality of their bonding phases significantly affect their service performances. The purpose of this study was to characterize the microstructures of industrial brick samples to develop a protocol to compare different products e.g. for evaluation as replacement bricks. In some of the chromite containing bricks iron-rich rims were observed, while a domestic brick with similar chemistry had no such feature. These iron-rich rims were examined using SEM-EDS. It was found that the counter-diffusion of Fe+3 and Cr+3 were responsible for their formation. Exsolved chrome-spinel was widely observed in the microstructures of chromite bricks. Magnesia-spinel bricks were found to contain low melting calcium aluminates as bond phases in the microstructure, posing a threat to service performance. Portmortem microanalysis of industrially used bricks revealed alkali attack in addition to creep as main destruction mechanisms for brick. Traces of elements like Mo, S and alkalies were observed and thought to originate from the use of waste derived fuels.