Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
Search Results
Article Citation - WoS: 4Citation - Scopus: 4Novel Electrospun-Based Extractive Probes for Rapid Determination of Clinically Important Compounds in Human Plasma(Elsevier B.V., 2024) Eroğlu, Ahmet Emin; Eroğlu,A.E.; Salih,B.; Boyaci,E.; 01. Izmir Institute of Technology; 04.01. Department of Chemistry; 04. Faculty of ScienceBackground: Coated blade spray (CBS) represents an innovative approach that utilizes solid-phase microextraction principles for sampling and sample preparation. When combined with ambient mass spectrometry (MS), it can also serve as an electrospray ionization source. Therefore, it became a promising tool in analytical applications as it can significantly reduce the analysis time. However, the current CBS coatings are based on the immobilization of extractive particles in bulk polymeric glue, which constrains the diffusion of the analytes to reach the extractive phase; therefore, the full reward of the system cannot be taken at pre-equilibrium. This has sparked the notion of developing new CBS probes that exhibit enhanced kinetics. Results: With this aim, to generate a new extractive phase with improved extraction kinetics, poly(divinylbenzene) (PDVB) nanoparticles were synthesized by mini-emulsion polymerization and then immobilized into sub-micrometer (in diameter) sized polyacrylonitrile fibers which were obtained by electrospinning method. Following the optimization and characterization studies, the electrospun-coated blades were used to determine cholesterol, testosterone, and progesterone in plasma spots using the CBS-MS approach. For testosterone and progesterone, 10 ng mL−1 limits of quantification could be obtained, which was 200 ng mL−1 for cholesterol in spot-sized samples without including any pre-treatment steps to samples prior to extraction. Significance: The comparison of the initial kinetics for dip-coated and electrospun-coated CBS probes proved that the electrospinning process could enhance the extraction kinetics; therefore, it can be used for more sensitive analyses. The total analysis time with this method, from sample preparation to instrumental analysis, takes only 7 min, which suggests that the new probes are promising for fast diagnostic applications. © 2024 Elsevier B.V.Article Citation - WoS: 7Citation - Scopus: 7Improving Mechanical Behavior of Adhesively Bonded Composite Joints by Incorporating Reduced Graphene Oxide Added Polyamide 6,6 Electrospun Nanofibers(Elsevier Sci Ltd, 2024) Tanoğlu, Metin; Barışık, Murat; Tanoglu, Metin; Ulas, M. Erdal; Nuhogu, Kaan; Esenoglu, Gozde; Iris, M. Erdem; 03.10. Department of Mechanical Engineering; 03. Faculty of Engineering; 01. Izmir Institute of TechnologyAdhesive joining of fiber-reinforced polymer (FRP) composites requires adequate interface tailoring and careful surface preparation to obtain a strong bond between components. This study aimed to improve the mechanical performance of adhesively bonded unidirectional carbon fiber-based (CFRP) composite parts by modifying joint surfaces with graphene-added electrospun Polyamide 6,6 (PA66) nanofibers. Reduced graphene oxide (rGO) was dispersed at 10 % wt/v PA66 solution at three different concentrations below rGO saturation limits. Bead-free nanofibers with homogenous graphene distribution were obtained on a prepreg by electrospinning. Addition of up to 2 % rGO yielded complete dispersion through the nanofiber network while the higher values created local agglomerations. Surface wetting experiments showed conversion of slightly hydrophobic surfaces to complete hydrophilic with electrospun nanofiber coating and the lowest contact angle was obtained at 2 % wt/v rGO addition (26.18 degrees +/- 2.03 degrees). Composite plates were produced in a hot press keeping the modified prepregs on top. Plates with different surface treatments joined by secondary bonding using 3 plies of FM 300 K film adhesive. Mechanical properties of adhesively bonded composites were tested by Single lap joint and Charpy impact tests. We achieved an 18 % increase in shear strength and 31 % increase in impact strength by adding 2 % wt/v ratio rGO into PA66 electrospun nanofiber.Review Citation - WoS: 5Citation - Scopus: 5Development and Functionalization of Electrospun Fiber Coated Thin Film Microextraction Devices for Rapid Mass Spectrometric Determination of Biologically Important Polar Molecules(Elsevier B.V., 2024) Eroğlu, Ahmet Emin; Salih,B.; Eroğlu,A.E.; Boyaci,E.; 01. Izmir Institute of Technology; 04.01. Department of Chemistry; 04. Faculty of ScienceRapid diagnosis of diseases is one of the challenging areas in clinical research. From the analytical chemist's perspective, the main challenges are isolating the compounds from the bio-specimen and lengthy analysis times. In this regard, solid phase microextraction offers a platform to address the abovementioned challenges. Moreover, its sharp tip-thin film geometry, known as coated blade spray (CBS), can enhance the extraction and act as an ionization source in direct mass spectrometric analysis. In this study, a new CBS device specifically designed for polar analytes was prepared and optimized to determine urinary metabolites. For this purpose, polyacrylonitrile (PAN) was selected as a base polymer as it can be electrospun to form a nanofibrous structure, and it can be modified with weak ion exchange moieties to interact with polar analytes. Following the electrospinning of PAN, hydrolysis was optimized, and conditions leading to sufficient extraction enhancement without dissolving the polymer were obtained when probes were treated with 5.0 M of NaOH for 2.5 h. Using the coated blades prepared as explained, the evaluation of various extraction conditions showed that 5 min is sufficient for equilibrium extraction. In addition, the solution's ionic strength and pH significantly affect the extraction. Optimum sorption was obtained at no salt added and pH 7.0 conditions. The CBS-MS optimization showed that 10.0 µL of ACN/MeOH/H2O (40:40:20, v/v/v) with formic acid kept for 15 seconds on the blade before voltage application leads to the highest signal. The limits of quantification of the analytes are between 50 and 100 ng/mL. © 2024 Elsevier B.V.