Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
7 results
Search Results
Article Microstructure-Based Prediction of Mechanical Properties of Austempered Ductile Iron Using Multiple Linear Regression Analysis(Springer int Publ Ag, 2025) Yalcin, M. Alp; Davut, KemalMultiple linear regression analysis (MLRA) was used to predict the mechanical properties of austempered ductile iron (ADI) including yield and tensile strength, uniform elongation, hardening exponent, as well as fracture energy by building a model that uses characteristic features of microstructural constituents as input parameters. The complex multi-scale microstructure of ADI, which is composed of spherical graphite particles over 10 mu m diameter; and an ausferritic matrix with sub-micron sized features, makes it ideal for prediction of mechanical properties. For that purpose, low alloyed ductile iron samples austempered between 300 and 400 degrees C for 45-180 min were tensile tested, and also multi-scale microstructural characterization were carried out using optical microscope, SEM, and EBSD technique. Moreover, a sensitivity analysis was performed to determine which microstructural parameter(s) each mechanical property is most sensitive to. The results show that tensile and yield strength are most sensitive to size and morphology of matrix phases. Moreover, the size and aspect ratio of acicular ferrite correlate well with those of high-carbon austenite; since both form during transformation of parent austenite into ausferrite during austempering treatment. Equiaxed parent austenite grains transform into ausferrite with acicular morphology during the austempering treatment; and presence of equiaxed austenite grains in the austempered samples indicates untransformed regions during austempering treatment. Ductility was found to be more sensitive to nodularity of graphite particles, and this sensitivity was attributed to the size difference between graphite particles and grain size of matrix phases.Article Citation - WoS: 3Citation - Scopus: 3Nondestructive Microstructural Characterization of Austempered Ductile Iron(Walter de Gruyter GmbH, 2023) Tüzün, Mert Yağız; Yalçın, Mustafa Alp; Davut, Kemal; Kılıçlı, VolkanAustempered ductile iron (ADI) has been preferred in a wide range of applications due its unique combination of high strength, good ductility, wear resistance and fracture toughness together with lower cost and lower density compared to steels. Magnetic Barkhausen noise (MBN) measurement offers a better alternative to traditional characterization techniques by being fast and non-destructive. A simple linear regression using only one single independent variable cannot correlate the MBN with the microstructure of ADI, since its microstructure is multi component. Multiple linear regression analysis (MLRA) was used to build a model that uses the characteristic features of microstructural constituents as input parameters to predict the MBN. For that purpose, Cu-Ni-Mo alloyed ductile iron samples austempered between 325 and 400 degrees C and for 45-180 min duration were used. The results show that MBN is most sensitive to the size and shape of acicular ferrite and retained austenite. Moreover, MBN is almost insensitive to the size, morphology and volume fraction of graphite particles. This indicates that retained austenite pins the domain walls more effectively than the graphite particles. Considering the results MLRA, MBN technique can be used to characterize the ausferritic microstructure of ADI.Article Citation - WoS: 16Citation - Scopus: 17Investigation of the High Temperature Dry Sliding Wear Behavior of Graphene Nanoplatelets Reinforced Aluminum Matrix Composites(SAGE Publications, 2021) Martin, Seçkin; Kandemir, Sinan; Antonov, M.In this study, graphene nanoplatelets (GNPs) with a thickness of 50-100 nm have been utilized to improve the mechanical and tribological properties of A360 alloy due to their extraordinary mechanical properties and solid lubricant nature. For the investigation of tribological properties, ball-on disc tests were carried out at various temperatures including room temperature (RT), 150 °C, and 300 °C. According to the hardness and ball-on-disc test results, the nanocomposite samples reinforced with GNPs exhibited improved hardness and wear resistance. The improvement in the wear behavior of nanocomposites was referred to the temporarily formed solid lubricant film of harder GNPs during the wear, and hence coefficient of friction (COF) and volume loss were considerably reduced. Abrasive-adhesive, oxidative, and mild-to-severe were found to be main wear mechanisms at RT, 150 °C, and 300 °C, respectively. Overall, the results show that the nanocomposites fabricated by casting method combined with mechanical stirring and ultrasonication have promising wear performance, especially at elevated temperatures. This may suggest that these developed materials could be potential candidates to be used in the engineering applications requiring high temperature wear performance. © The Author(s) 2020.Article Citation - WoS: 4Citation - Scopus: 5Effects of Tib2 Nanoparticle Content on the Microstructure and Mechanical Properties of Aluminum Matrix Nanocomposites(Walter de Gruyter GmbH, 2017) Kandemir, SinanThe present work reports the fabrication of A357 alloy matrix nanocomposites reinforced with 0.5, 1.0 and 2.0 wt.-% TiB2 nanoparticles (20-30 nm) by a novel method which is the combination of semi-solid mechanical mixing and ultrasonic dispersion of nanoparticles in liquid state. The microstructural and mechanical properties of the fabricated nanocomposites were investigated. The microstructural studies conducted with optical and advanced electron microscopes indicated that reasonably effective deagglomeration and uniform distribution of TiB2 nanoparticles into the matrix were achieved. Transmission electron microscopy studies also confirmed that the nanoparticles were embedded into the matrix and a good bonding was obtained between the matrix and the reinforcement. Increasing nanoparticle content led to grain refinement and significant enhancement in the mechanical properties of nanocomposites. The addition of 0.5, 1.0, and 2.0 wt.-% TiB2 nanoparticles increased the 0.2 % proof stress of matrix alloy by approximately 31, 48 and 61 %, respectively. The contribution of different mechanisms to the strength enhancement is discussed. It is proposed that the strengthening is mainly due to Orowan mechanism and dislocation generation effect by the coefficient of thermal expansion mismatch between the TiB2 nanoparticles and the matrix.Article Citation - WoS: 11Citation - Scopus: 12Electrical Properties of Gadolinia Doped Ceria Electrolytes Fabricated by Infiltration Aided Sintering(Elsevier Ltd., 2019) Sındıraç, Can; Büyükaksoy, Aligül; Akkurt, SedatCommon solid oxide fuel cell (SOFC) electrolyte materials (e.g., gadolinia doped ceria - GDC) demand temperatures exceeding 1400 degrees C for densification by conventional solid state sintering. It is very desirable to reduce the densification of the SOFC electroltytes to i) avoid microstructural coarsening of the composite anode layers, which are co-sintered with the electolyte layer in the anode supported SOFC fabrication scheme and ii) reduce energy consumption during SOFC manufacturing. We have recently demostrated a novel infiltration-aided sintering route to densify GDC ceramics at 1200 degrees C. In the present work, we present the electrical properties of GDC ceramics fabricated thusly. Comparison of high density (>= 95%) samples fabricated by conventional or infiltration-aided sintering reveal that at 700 degrees C, similar total electrical conductivities are obtained, while at 300 degrees C, specific grain boundary resistivity is smaller in the latter. Bulk (grain) conductivity is higher in porous GDC ceramics (relative density <= 90%) fabricated by infiltration-aided sintering than the conventionally sintered ones with similar porosities. Finally, open circuit voltage of 0.84 V at 700 degrees C, obtained under dilute hydrogen and stagnant air conditions suggests that GDC ceramics densified by infiltration-aided sintering are suitable for use as SOFC electrolytes.Article Citation - WoS: 35Citation - Scopus: 39Development of Graphene Nanoplatelet-Reinforced Az91 Magnesium Alloy by Solidification Processing(Springer Verlag, 2018) Kandemir, SinanIt is a challenging task to effectively incorporate graphene nanoplatelets (GNPs) which have recently emerged as potential reinforcement for strengthening metals into magnesium-based matrices by conventional solidification processes due to their large surface areas and poor wettability. A solidification processing which combines mechanical stirring and ultrasonic dispersion of reinforcements in liquid matrix was employed to develop AZ91 magnesium alloy matrix composites reinforced with 0.25 and 0.5 wt.% GNPs. The microstructural studies conducted with scanning and transmission electron microscopes revealed that fairly uniform distribution and dispersion of GNPs through the matrix were achieved due to effective combination of mechanical and ultrasonic stirring. The GNPs embedded into the magnesium matrix led to significant enhancement in the hardness, tensile strength and ductility of the composites compared to those of unreinforced AZ91 alloy. The strength enhancement was predominantly attributed to the grain refinement by the GNP addition and dislocation generation strengthening due to the coefficient of thermal expansion mismatch between the matrix and reinforcement. The improved ductility was attributed to the refinement of β eutectics by transforming from lamellar to the divorced eutectics due to the GNP additions. In addition, the strengthening efficiency of the composite with 0.25 wt.% GNP was found to be higher than those of the composite with 0.5 wt.% GNP as the agglomeration tendency of GNPs is increased with increasing GNP content. These results were compared with those of the GNP-reinforced magnesium composites reported in the literature, indicating the potential of the process introduced in this study in terms of fabricating light and high-performance metal matrix composites.Article Citation - WoS: 19Citation - Scopus: 23Influence of Microstructure on the Rheological Behavior of Dense Particle Gels(John Wiley and Sons Inc., 2005) Wyss, Hans M.; Deliormanlı, Aylin M.; Tervoort, Elena V.; Gauckler, Ludwig JuliusRheological measurements are performed on highly concentrated alumina gels. By using an in situ mechanism based on enzyme-catalyzed internal reactions, we are able to form gels of highly concentrated particles without disturbing the microstructures that develop during the gelation process. These gels are produced by two different destabilization mechanisms: Either the pH of the suspension is shifted toward the isoelectric point (ΔpH method) or the ionic strength of the suspension is increased at a constant pH (ΔI method). The two destabilization mechanisms lead to gels of significantly different microstructures. We find notable differences in the rheological behavior of the two systems, suggesting a bond-bending mechanism for stress transmission in the case of ΔpH gels and a bond-stretching mechanism in the case of ΔI gels. In addition, for both kinds of gels we compare the in situ properties to those obtained after altering the microstructure by shearing. Results suggest an increase in elastic and yield properties of concentrated particle gels with decreasing homogeneity of their microstructures.