Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
11 results
Search Results
Now showing 1 - 10 of 11
Article Citation - WoS: 15Citation - Scopus: 15Granulation of Hydrometallurgically Synthesized Spinel Lithium Manganese Oxide Using Cross-Linked Chitosan for Lithium Adsorption From Water(Elsevier B.V., 2024) Recepoğlu,Y.K.; Arabacı,B.; Kahvecioğlu,A.; Yüksel,A.A drastic increase in demand for electric vehicles and energy storage systems increases lithium (Li) need as a critical metal for the 21st century. Lithium manganese oxides stand out among inorganic adsorbents because of their high capacity, chemical stability, selectivity, and affordability for lithium recovery from aqueous media. This study investigates using hydrometallurgically synthesized lithium manganese oxide (Li1.6Mn1.6O4) in granular form coated with cross-linked chitosan for lithium recovery from water. Characterization methods such as SEM, FTIR, XRD, and BET reveal the successful synthesis of the composite adsorbent. Granular cross-linked chitosan-coated and delithiated lithium manganese oxide (CTS/HMO) adsorbent demonstrated optimal removal efficiency of 86 % at pH 12 with 4 g/L of adsorbent dosage. The Langmuir isotherm at 25 °C, which showed monolayer adsorption with a maximum capacity of 4.94 mg/g, a better fit for the adsorption behavior of CTS/HMO. Adsorption was endothermic and thermodynamically spontaneous. Lithium adsorption followed the pseudo-first-order kinetic model. © 2024Article Citation - WoS: 4Citation - Scopus: 5Breakthrough Curve Analysis of Phosphorylated Hazelnut Shell Waste in Column Operation for Continuous Harvesting of Lithium From Water(Elsevier, 2024) Recepoğlu, Yaşar Kemal; Arar, Ozguer; Yuksel, AsliIn batch-scale operations, biosorption employing phosphorylated hazelnut shell waste (FHS) revealed excellent lithium removal and recovery efficiency. Scaling up and implementing packed bed column systems necessitates further design and performance optimization. Lithium biosorption via FHS was investigated utilizing a continuous-flow packed-bed column operated under various flow rates and bed heights to remove Li to ultra-low levels and recover it. The Li biosorption capacity of the FHS column was unaffected by the bed height, however, when the flow rate was increased, the capacity of the FHS column decreased. The breakthrough time, exhaustion time, and uptake capacity of the column bed increased with increasing column bed height, whereas they decreased with increasing influent flow rate. At flow rates of 0.25, 0.5, and 1.0 mL/min, bed volumes (BVs, mL solution/mL biosorbent) at the breakthrough point were found to be 477, 369, and 347, respectively, with the required BVs for total saturation point of 941, 911, and 829, while the total capacity was calculated as 22.29, 20.07, and 17.69 mg Li/g sorbent. In the 1.0, 1.5, and 2.0 cm height columns filled with FHS, the breakthrough times were 282, 366, and 433 min, respectively, whereas the periods required for saturation were 781, 897, and 1033 min. The three conventional breakthrough models of the Thomas, Yoon-Nelson, and Modified Dose-Response (MDR) were used to properly estimate the whole breakthrough behavior of the FHS column and the characteristic model parameters. Li's extremely favorable separation utilizing FHS was evidenced by the steep S-shape of the breakthrough curves for both parameters flow rate and bed height. The reusability of FHS was demonstrated by operating the packed bed column in multi-cycle mode, with no appreciable loss in column performance.Article Citation - WoS: 7Citation - Scopus: 7Cross-Linked Phosphorylated Cellulose as a Potential Sorbent for Lithium Extraction From Water: Dynamic Column Studies and Modeling(American Chemical Society, 2022) Recepoğlu, Yaşar Kemal; Yüksel, AslıPhosphorylated functional cellulose was cross-linked with epichlorohydrin at different ratios because it is a very hydrophilic substance that instantly swells to form a hydrogel when it comes into contact with water. It was aimed to utilize a continuously packed bed column to recover lithium from water under varying operating conditions such as flow rate and bed height. The characterization results confirmed cross-linking based on morphology, structure, surface area, and thermal stability differences. Lithium recovery was more efficient with a low flow rate, but the dynamic sorption process was independent of bed height. The total capacities at the three flow rates with 1.5 cm bed height were 33.56, 30.15, and 25.54 mg g-1, and the total saturation times at the three different bed heights with 0.5 mL min-1 flow rate were 659, 1001, and 1007 min, respectively. Only 15.75 mL of 5% H2SO4 solution was required to desorb approximately 100% of Li from the saturated sorbent.Article Citation - WoS: 13Citation - Scopus: 11Valorization of Olive Tree Pruning Waste for Potential Utilization in Lithium Recovery From Aqueous Solutions(Springer, 2022) Nampeera, Jackline; Recepoğlu, Yaşar Kemal; Yüksel, AslıOlive tree pruning waste, mainly composed of olive branches, was converted into a value-added and sustainable product capable of lithium as a biosorbent through alkali treatment and phosphorylation reaction. Characterization studies were performed by SEM–EDX, XPS, FTIR, and TGA. Factors affecting biosorption mechanism, i.e., sorbent dosage, pH, initial Li+ concentration and temperature, and competitive ions’ presence, were investigated the synthesized functionalized olive branches (FOB). A commercial lithium selective resin, Lewatit TP 260, was also compared with FOB in batch and column studies. The Freundlich model fits adsorption isotherms better than the Langmuir model, with a maximum adsorption capacity of 6.7 mg/g at 30 °C and pH 7–8. Kinetic studies proved fast kinetics and equilibrium were attained in 6 min, while thermodynamic studies showed an exothermic (Δ Ho= - 17.52 kJ/ mol) , spontaneous reaction Δ Go< 0 at all temperatures), and increased randomness Δ So= + 24.27 J/ mol. K) at the interaction interface. Column studies revealed that although Lewatit TP 260 resin showed higher sorption capacity, its desorption efficiency (50.42%) was lower than that of FOB (99.9%), and the degree of column utilization of FOB (56.81%) was better than Lewatit TP 260 resin’s (16.0%). The findings were encouraging in the successful synthesis of a promising biosorbent from an abundant waste in Turkey for use in sustainable lithium recovery from aqueous sources. Graphical abstract: [Figure not available: see fulltext.]Article Citation - WoS: 17Citation - Scopus: 16Synthesis, Characterization and Adsorption Studies of Phosphorylated Cellulose for the Recovery of Lithium From Aqueous Solutions(Editura Acad Romane, 2021) Recepoğlu, Yaşar Kemal; Yüksel, AslıIn this study, pristine cellulose was functionalized by the phosphorylation reaction to make it suitable for lithium separation. After characterization studies of the synthesized adsorbent with SEM, EDX, FTIR, TGA and XPS, the effects of various parameters on the lithium uptake capacity of the adsorbent were examined. The analysis of equilibrium data by several adsorption models showed that maximum adsorption capacity of the adsorbent was found to be 9.60 mg/g at 25 degrees C by the Langmuir model. As initial concentration and contact time increased, adsorption capacity also increased, however, mild temperature (25-35 degrees C) and pH (5-6) were better for the adsorption of lithium. 80% of lithium adsorption within three minutes proved the fast kinetic nature of the adsorbent. A 99.5% desorption efficiency of lithium was achieved with 0.5 M H2SO4, among HCl and NaCl with different molarities. Phosphorylated cellulose was shown to be a favorable adsorbent for the recovery of lithium from aqueous solutions.Article Citation - WoS: 25Citation - Scopus: 26Phosphorylated Hazelnut Shell Waste for Sustainable Lithium Recovery Application as Biosorbent(Springer, 2021) Recepoğlu, Yaşar Kemal; Yüksel, AslıHazelnut shell waste was phosphorylated to develop a novel biosorbent based on natural renewable resource for the recovery of lithium from aqueous solution. For the synthesized biosorbent, the surface morphology and mapping by SEM-EDS, chemical properties by FTIR, elemental analysis by XPS, specific surface area by BET, crystallinity by XRD and thermal properties by TGA were elucidated elaborately. The influence of biosorbent dosage, initial concentration, temperature, contact time, pH and coexisting ions were investigated. The equilibrium sorption capacity reached 6.03 mg/g under optimal conditions (i.e., biosorbent dosage of 12.0 g/L, initial Li concentration of 100 mg/L, pH value of 5.8, sorption temperature of 25 degrees C, and sorption time of 6 min). According to the sorption behavior of the phosphorylated hazelnut shell waste the Freundlich model proved to be more suitable than the Langmuir model indicating maximum sorption capacity as 7.71 mg/g at 25 degrees C. Thermodynamic parameters obtained by different isokinetic temperatures disclosed that the ion exchange reaction was feasible, spontaneous, and exothermic where the interaction between biosorbent surface and solvent plays an important role. A preliminary test on the Li recovery from geothermal water was also performed to check its applicability in a real brine. Desorption studies at 25 degrees C revealed that relatively higher desorption efficiency and capacity were achieved at 97.4% and 5.93 mg/g, respectively with a 1.0 M H2SO4 among other regenerants (i.e., HCl and NaCl). Concentrations of Li and the other cations were determined via ICP-OES. Due to such outstanding features, the novel phosphorylated hazelnut shell waste had great potential for lithium recovery from aqueous solution by being added value as a waste and recovering a strategic element of modern life simultaneously. [GRAPHICS] .Article Citation - WoS: 17Citation - Scopus: 19Effect of Operational Conditions on Separation of Lithium From Geothermal Water by ?-Mno2 Using Ion Exchange–membrane Filtration Hybrid Process(Taylor and Francis Ltd., 2018) Recepoğlu, Yaşar Kemal; Kabay, Nalan; Yoshizuka, Kazuharu; Nishihama, Syouhei; Yılmaz İpek, İdil; Arda, Müşerref; Yüksel, MithatA hybrid system coupling ion exchange and ultrafiltration (UF) was employed to separate lithium from lithium-spiked geothermal water. The effect of process parameters such as adsorbent type, adsorbent dosage, permeate flow rate, and replacement speeds of fresh and saturated adsorbents have been evaluated to determine the efficiency of the hybrid system. According to the results obtained using λ-MnO2 derived from spinel-type lithium manganese dioxide, the optimal operating conditions to separate lithium from geothermal water were found with powdery λ-MnO2 with an adsorbent concentration of 1.5 g adsorbent/L solution, replacement rates of fresh and saturated adsorbents of 6.0 mL/min, and a permeate flow rate of 5.0 mL/min. The ion exchange–UF hybrid system providing an advantage to work with very fine particles easily can be considered as a favorable process for the separation of lithium from geothermal water.Article Citation - WoS: 1Citation - Scopus: 1Adsorption and Diffusion Characteristics of Lithium on Hydrogenated ?- and Ss-Silicene(Beilstein-Institut Zur Forderung der Chemischen Wissenschaften, 2017) İyikanat, Fadıl; Kandemir, Ali; Bacaksız, Cihan; Şahin, HasanUsing first-principles density functional theory calculations, we investigate adsorption properties and the diffusion mechanism of a Li atom on hydrogenated single-layer α- and β-silicene on a Ag(111) surface. It is found that a Li atom binds strongly on the surfaces of both α- and β-silicene, and it forms an ionic bond through the transfer of charge from the adsorbed atom to the surface. The binding energies of a Li atom on these surfaces are very similar. However, the diffusion barrier of a Li atom on H-α-Si is much higher than that on H-β-Si. The energy surface calculations show that a Li atom does not prefer to bind in the vicinity of the hydrogenated upper-Si atoms. Strong interaction between Li atoms and hydrogenated silicene phases and low diffusion barriers show that α- and β-silicene are promising platforms for Li-storage applications.Article Citation - WoS: 2Citation - Scopus: 4Use of Electrospun Fiber Mats for the Remediation of Hypersaline Geothermal Brine(Desalination Publications, 2017) Çelik, Aslı; Koç, Gonca; Erdoğan, Emre; Shahwan, Talal; Baba, Alper; Demir, Mustafa MuammerGeothermal brines display high contents of various metal ions that can adversely affect surface and groundwater resources. Nevertheless, it is possible to sequestrate these metals and use some of them in certain engineering applications. The aim of this study was to fabricate electrospun chitosan fiber mats and remove heavy metal cations from geothermal brine of the Tuzla geothermal field (TGF) by employing these mats. TGF is located on the Biga Peninsula in the northwestern part of Turkey. The brine of TGF has high salinity (EC > 91 mS/cm) and high temperature (reservoir temperature is 173°C). The brine is rich in terms of metal cations. For instance, the concentration of lithium ion in geothermal fluid ranges from 17 to 35 mg/L, with little seasonal variations. A horizontal electrospinning setup was employed to obtain a non-woven mat comprising submicron diameter chitosan fibers at 2.0 kV∙cm−1. This material was then utilized as a stable membrane for the removal of metal ions present in the brine through sorption at 25°C overnight. The results showed that the chitosan fiber mats sequestrate various ions in the brine. Under the studied conditions, the material was capable of removing 46%, 44%, 50%, 44%, 40%, 67% and 48% of Li+, Mg2+, Ba2+, Sr2+, Mn2+, Ca2+ and K+ from the geothermal brine, respectively.Article Citation - WoS: 66Citation - Scopus: 71Lithium Protects Against Paraquat Neurotoxicity by Nrf2 Activation and Mir-34a Inhibition in Sh-Sy5y Cells(Frontiers Media S.A., 2015) Alural, Begüm; Özerdem, Ayşegül; Allmer, Jens; Genç, Kürşad; Genç, ŞerminLithium is a mood stabilizing agent commonly used for the treatment of bipolar disorder. Here, we investigated the potential neuroprotective effect of lithium against paraquat toxicity and its underlying mechanisms in vitro. SH-SY5Y human neuroblastoma cells were treated with paraquat (PQ) 0.5 mM concentration after lithium pretreatment to test lithium's capability in preventing cell toxicity. Cell death was evaluated by LDH, WST-8, and tryphan blue assays. Apoptosis was analyzed using DNA fragmentation, Annexin V immunostaining, Sub G1 cell cycle analysis, and caspase-3 activity assays. BCL2, BAX, and NRF2 protein expression were evaluated by Western-blotting and the BDNF protein level was determined with ELISA. mRNA levels of BCL2, BAX, BDNF, and NRF2 target genes (HO-1, GCS, NQO1), as well as miR-34a expression were analyzed by qPCR assay. Functional experiments were done via transfection with NRF2 siRNA and miR-34a mimic. Lithium treatment prevented paraquat induced cell death and apoptosis. Lithium treated cells showed increased anti-apoptotic protein BCL2 and decreased pro-apoptotic protein BAX expression. Lithium exerted a neurotrophic effect by increasing BDNF protein expression. It also diminished reactive oxygen species production and activated the redox sensitive transcription factor NRF2 and increased its target genes expression. Knockdown of NRF2 abolished neuroprotective, anti-apoptotic, and anti-oxidant effects of lithium. Furthermore, lithium significantly decreased both basal and PQ-induced expression of miR-34a. Transfection of miR-34a specific mimic reversed neuroprotective, anti-apoptotic, and anti-oxidant effects of lithium against PQ-toxicity. Our results revealed two novel mechanisms of lithium neuroprotection, namely NRF2 activation and miR-34a suppression.