Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection

Permanent URI for this collectionhttps://hdl.handle.net/11147/7148

Browse

Filters

2011 - 20203

Settings

Author: search.filters.author.Şahmaran, MustafaSubject: search.filters.subject.Fly ash

Search Results

Now showing 1 - 3 of 3
  • Article
    Citation - WoS: 10
    Citation - Scopus: 10
    Effects of Mixture Design Parameters on the Mechanical Behavior of High-Performance Fiber-Reinforced Concretes
    (American Society of Civil Engineers (ASCE), 2020) Erdem, Tahir Kemal; Demirhan, Serhat; Yıldırım, Gürkan; Banyhussan, Qais S.; Şahin, Oğuzhan; Balav, Mohammad H.; Şahmaran, Mustafa
    The main purpose of this research is to assess the influence of different design parameters on the mechanical performance of high-performance fiber-reinforced concrete (HPFRC) mixtures. Special attention is also paid to achieving deflection-hardening behavior in the presence of a large amount of coarse aggregates. Different mixture design parameters were the initial curing ages (3, 7, 28, and 90 days), ratios of Class F fly ash (FA) to portland cement (PC) (0.0, 0.2, and 0.4), addition/type of nanomaterials [nanosilica (NS), nanoalumina (NA), and nanocalcite (NC)], and combinations of fibers [polyvinyl-alcohol + steel (P, S) or brass-coated microsteel + steel (B, S)]. The experimental program included the evaluation of compressive strength, flexural strength, and midspan deflection results in addition to test parameters recorded under biaxial flexural loading via a series of square panel tests, including peak load and energy absorption capacities. Test results revealed that deflection-hardening response coupled with multiple microcracks can be obtained when large amounts of coarse aggregates are available for all HPFRC mixtures. As expected, experimental results change depending on the different curing ages and FA/PC ratios. The most distinctive parameters affecting the results are addition/type of nanomaterials and the presence of different fiber combinations. In the presence of nanomaterials, all results from the different tests improved, especially for NA and NS inclusions. With slight concessions in flexural deflection results, B fiber is shown to be a successful candidate to fully replace costly P fibers because most properties of B, S fiber-reinforced HPFRC mixtures outperformed those with P, S fibers, both under four-point bending and biaxial flexural loading.
  • Article
    Citation - WoS: 47
    Citation - Scopus: 53
    Effect of Sustained Flexural Loading on Self-Healing of Engineered Cementitious Composites
    (Japan Concrete Institute, 2013) Özbay, Erdogan; Şahmaran, Mustafa; Yücel, Hasan Erhan; Erdem, Tahir Kemal; Lachemi, Mohamed; Li, Victor C.
    This paper aims to clarify the effects of sustained flexural loading on the self-healing behavior of Engineered Cementitious Composites (ECC). Prismatic specimens of ECC mixtures with two different levels of Class-F fly ash content were cast. Flexural loading was applied to the specimens at 28 days age to generate severe amount of microcracks. The specimens were then stored under continuous water or air exposures with or without sustained mechanical loading, for up to 90 days. For specimens under sustained mechanical loading, the applied sustained load level was 60% of the ultimate flexural strength. The extent of damage was determined as a percentage of loss in mechanical properties. The influences of different exposure regimes and sustained mechanical loading on mechanical properties of ECC mixtures were investigated. Microstructural changes within the microcracks were also analyzed.
  • Article
    Citation - WoS: 75
    Citation - Scopus: 87
    Use of Spent Foundry Sand and Fly Ash for the Development of Green Self-Consolidating Concrete
    (Springer Verlag, 2011) Şahmaran, Mustafa; Lachemi, Mohamed; Erdem, Tahir Kemal; Yücel, Hasan Erhan
    In the United States alone, the foundry industry discards up to 10 million tons of sand each year, offering up a plentiful potential resource to replace sand in concrete products. However, because the use of spent foundry sand (SFS) is currently very limited in the concrete industry, this study investigates whether SFS can successfully be used as a sand replacement material in cost-effective, green, self-consolidating concrete (SCC). In the study, SCC mixtures were developed to be even more inexpensive and environmentally friendly by incorporating Portland cement with fly ash (FA). Tests done on SCC mixtures to determine fresh properties (slump flow diameter, slump flow time, V-funnel flow time, yield stress, and relative viscosity), compressive strength, drying shrinkage and transport properties (rapid chloride permeability and volume of permeable pores) show that replacing up to 100% of sand with SFS and up to 70% Portland cement with FA enables the manufacture of green, lower cost SCC mixtures with proper fresh, mechanical and durability properties. The beneficial effects of FA compensate for some possible detrimental effects of SFS.