Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
14 results
Search Results
Now showing 1 - 10 of 14
Article Citation - WoS: 2Citation - Scopus: 10Water and Water Vapor Sorption Studies in Poly(propylene)-Zeolite Composites(John Wiley and Sons Inc., 2003) Pehlivan, Hilal; Özmıhçı, Filiz; Tıhmınlıoğlu, Funda; Balköse, Devrim; Ülkü, SemraWater and water vapor sorption to porous poly(propylene)zeolite composites prepared by hot pressing have been studied as a function of zeolite loading. This work presents the first report on the effect of the zeolite as a filler on the water sorption properties of PP composites. Water swelling experiments were conducted at 25°C using pure PP and PP-zeolite film samples having different zeolite loadings (6-40 wt%). Since PP is a hydrophobic polymer, it does not sorp any water, but the composites having 10, 20, 30, and 40% zeolite sorbed 0.63, 1.00, 1.72 and 3.74 wt% water, respectively. The zeolite itself at the same conditions sorbed 24.5 wt% water. As the filler loading in the composites increased, equilibrium uptake values increased too. On the other hand, water vapor sorption and kinetics has been studied using a Cahn 2000 gravimetric sorption system. Within in the range 0.35-0.95%, water vapor was adsorbed by the composites containing 10-40 wt% zeolite. Experimental effective water vapor diffusivities of the composite films were about one order of magnitude higher than the experimental water diffusion coefficient in composites. The transport of water in composites was slower than that in the liquid water due to the longer diffusion pathway and adsorption on the surface of the composites. Although the liquid water may fill all the voids in the composite, water vapor is adsorbed on the surface of the zeolite only.Article Citation - WoS: 2Citation - Scopus: 2A Study of Chemical and Physical Changes During Biaxially Oriented Polypropylene Film Production(Walter de Gruyter GmbH, 2003) Ülkü, Semra; Balköse, Devrim; Arkış, Esen; Sipahioğlu, MuzafferPolypropylene films obtained during the biaxial orientation process were characterized by energy dispersive X-ray analysis (EDX), scanning electron microscopy. X-ray diffraction, differential scanning calorimetry, infrared spectroscopy. Inorganic particles with Al, Si, Na, Mg, Ti, K,O elements were present in biaxially oriented films. Polypropylene had molecules with both isotactic configuration and it was crystallized only in isotactic α phase. The films drawn in one and two directions had unit cells with b axis parallel to surface of the films. The antioxidants present in the films were consumed during processing, preventing polypropylene oxidation in air at high processing temperatures. One surface of the films contained less polypropylene and had functional groups rich in oxygen such as C=O and COO.Article Citation - WoS: 6Citation - Scopus: 7Preparation and Characterization of Flexible Poly(vinyl Chloride) Foam Films(John Wiley and Sons Inc., 2012) Şahin, Erdem; Yaşar Mahlıçlı, Filiz; Yetgin, Senem; Balköse, DevrimIn this study, the effect of activator ZnO and heating time at 190°C on foaming, gelation, and dehydrochlorination of poly(vinyl chloride) (PVC) plastisol was investigated. For this purpose, a PVC plastisol was prepared by mixing PVC, dioctyl phthalate (DOP), azodicarbonamide (ADC), ZnO, and the heat stabilizers calcium stearate (CaSt 2) and zinc stearate(ZnSt 2). PVC plastisol films were heated for 3, 6, 12, and 24 min periods at 190°C to see the effect of heating time on the gelation and foaming processes of the PVC foam. The time of 12 min was determined to be optimum for the completion of gelation and foaming processes without thermal degradation of PVC. No foaming was observed under the same conditions for the samples without ZnO. ZnO had a significant catalytic effect on ADC decomposition, accelerating the foaming of the films. Average porosity measurement showed a consistent increase in porosity with heating time up to 76% and the average density decreased from 1.17 to 0.29 g/cm 3 on foaming. Tensile tests showed that the tensile strength and tensile strain both increased considerably up to 0.98 MPa and 207%, respectively, with heating time and the elastic modulus was seen to gradually decrease from 4.7 to 0.7 MPa with heating time. Films without ZnO had higher tensile strength since there were no pores. PVC thermomat tests showed that ZnO lowered the stability time of plastigel film with azodicarbonamide.Article Citation - WoS: 17Citation - Scopus: 21Effects of Particle Size and Electrical Resistivity of Filler on Mechanical, Electrical, and Thermal Properties of Linear Low Density Polyethylene-Zinc Oxide Composites(John Wiley and Sons Inc., 2013) Özmıhçı Ömürlü, Filiz; Balköse, DevrimThe effects of particle size and electrical resistivity of zinc oxide (ZnO) on mechanical properties, electrical and thermal conductivities of composites made with linear low density polyethylene (LLDPE) were investigated. Micron sized (mZnO), submicron sized (sZnO), and nano sized (nZnO) powders having resistivities of 1.5 × 106, 1.5 × 109, and 1.7 × 108 were used to prepare composites with 5-20 vol % filler. The tensile strength was lowered and the modulus of elasticity of the composites was increased with ZnO addition. Rather than the particle size of the ZnO, its initial resistivity and aspect ratio affected the resistivity of composites. The resistivity of the LLDPE was lowered from 2.3 × 1016 Ω cm down to 1.4 × 1010 Ω cm with mZnO addition. Thermal conductivity of the composites was increased with ZnO addition 2.5-3 times of the polymer matrix. The composites can be used for electrostatically dissipating and heat sink applications due to their decreased electrical resistivity and increased thermal conductivity.Article Citation - WoS: 10Citation - Scopus: 10Morphology, Order, Light Transmittance, and Water Vapor Permeability of Aluminum-Coated Polypropylene Zeolite Composite Films(John Wiley and Sons Inc., 2011) Balköse, Devrim; Oğuz, Kaan; Özyüzer, Lütfi; Tarı, Süleyman; Arkış, Esen; Özmıhçı Ömürlü, FilizIn this study, the polypropylene-zeolite composite films having 2-6 wt % natural zeolite were coated with a thin film of aluminum (Al) by magnetron sputtering, and the contribution of the Al coating on film properties was investigated. The samples were characterized by EDX, X-ray diffraction, SEM, AFM, UV-visible spectroscopy, and water vapor permeation analyses. The surface of the films coated with a smooth Al film having 98-131 nm thickness. EDX revealed that Al percentage on the surface appeared to be as 8-10 wt % indicating contribution of polymer surface under Al film to analysis. XRD analysis showed that the grain size of Al at the surface was 22-29 nm. The surface roughness increased after Al-coating process. The transmission of coated films was very low for both UV and visible regions of the light spectrum. Permeation analysis indicated that water vapor permeation was lower for Al-coated material.Article Citation - WoS: 12Citation - Scopus: 13Statistical Thermal Stability of Pvc(John Wiley and Sons Inc., 2010) Atakul Savrık, Sevdiye; Cansever Erdoğan, Beyhan; Balköse, Devrim; Ülkü, SemraExperimental design was used to optimize the processing parameters for the decomposition of poly (vinyl chloride). Factorial design and face centered composite design (FCC) were applied to determine the optimum conditions. A total of 10 g PVC powder was mixed with different amounts of zinc stearate (ZnSt 2) and natural zeolite and tested for thermal stability. Factorial fitted model was explained by first order pattern due to the significant main effect regression constants, and FCC model was described by second order model owing to higher order polynomial coefficients. FCC design was superior to factorial design as FCC considers not only its pure quadratic effects contribution but also its higher overall desirability for thermal stability of PVC. For factorial design the optimum conditions were determined as 163.06 mg for ZnSt2, 399.99 mg for zeolite, and 140°C for temperature with desirability of 0.933. However, 400 mg for ZnSt2, 333.24 mg for zeolite, and 140°C for temperature with desirability of 0.956 were obtained as the optimum conditions by FCC design. © 2010 Wiley Periodicals, Inc.Article Citation - WoS: 2Citation - Scopus: 1Stabilizing Effect of Biobased Additives on the Thermal Degradation of Pvc(Trans Tech Publications, 2010) Egbuchunam, Theresa Obuajulu; Okieimen, Felix Ebhodaghe; Balköse, DevrimNovel biobased additives prepared from rubber seed oil were evaluated as thermal stabilizer for PVC. Divalent metal (barium and cadmium) soaps of rubber seed oil were prepared by metathesis in aqueous alcohol and characterized by thermal methods (differential scanning calorimetry and thermogravimetry). The stabilizing effect of the soaps and their admixtures on the thermal degradation of PVC powder and plasticized PVC was examined by dynamic thermogravimetry and dehydrochlorination studies at 160°C using the Thermomat equipment. The metal soaps showed multiple decomposition endotherms but were generally stable (with weight loss less than 5%) within the temperature range (180-220°C) frequently used in the processing of PVC. Using the Broido model, values of apparent activation energy of decomposition of between 50 and 200 kJmol-1 were obtained for the soaps. The biobased additives were found to be relatively effective in stabilizing PVC in powder and plasticized forms against thermal degradation. Using inhibition/retardation time, temperature of incipient decomposition, and temperature at which various extents of decomposition was attained as indices of thermal stabilization, the results from this study indicate a potential for the application of the biobased additives as thermal stabilizer for PVC in rigid and flexible formulations. © (2010) Trans Tech Publications, Switzerland.Conference Object Citation - WoS: 18Citation - Scopus: 19Development of Synergistic Heat Stabilizers for Pvc From Zinc Borate-Zinc Phosphate(Taylor and Francis Ltd., 2009) Erdoğdu, Cem Aykut; Atakul, Sevdiye; Balköse, Devrim; Ülkü, SemraThe importance of flame-retardant and smoke-suppressed poly(vinyl chloride) (PVC) compositions is increasing gradually in the polymer industry since PVC releases smoke and toxic gases (hydrogen chloride, HCl) during heating at temperatures above 140°C with the result of dehydrochlorination reaction. In this study, the synergistic effects of zinc borate (ZB)-zinc phosphate (ZP) on the thermal stability of PVC were investigated using thermal techniques. The induction and stability time values of PVC plastigels were obtained at 140°C and 160°C. The results revealed that PVC plastigels having only ZP and ZB retarded dehydrochlorination of PVC compared with the unstabilized sample. However, the plastigels with both ZB and ZP had a superior synergistic effect on char formation of PVC. Since the induction periods of the samples having both ZB and ZP were higher than those of the unstabilized samples having only ZB or only ZP, the synergistic effect was observed.Article Citation - WoS: 18Citation - Scopus: 19Effect of Zeolite Filler on the Thermal Degradation Kinetics of Polypropylene(John Wiley and Sons Inc., 2006) Pehlivan, Hilal; Balköse, Devrim; Ülkü, Semra; Tıhmınlıoğlu, FundaIn this study, the thermal degradation behavior of polypropylene (PP) and PP-zeolite composites was investigated, Clinoptilolite, a natural zeolitic tuff, was used as the filler material in composites. The effects of both pure clinoptilolite and silver-ion-exchanged clinoptilolite on the thermal degradation kinetics of the PP composites was studied with differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Polymer degradation was evaluated with DSC at heating rates of 5, 10, and 20°C/ min from room temperature to 500°C. The silver concentration (4.36, 27.85, and 183.8 mg of Ag/g of zeolite) was the selected parameter under consideration. From the DSC curves, we observed that the heat of degradation values of the composites containing 2-6% silver-exchanged zeolite (321-390 kj/kg) were larger than that of the pure PP (258 kj/kg). From the DSC results, we confirmed that the PPzeolite composites can be used at higher temperatures than the pure PP polymer because of its higher thermal stability, The thermal decomposition activation energies of the composites were calculated with both the Kissinger and Ozawa models. The values predicted from these two equations were in close agreement. From the TGA curves, we found that zeolite addition into the PP matrix slowed the decomposition reaction; however, silver-exchanged zeolite addition into the matrix accelerated the reaction. The higher the silver concentration was, the lower were the thermal decomposition activation energies we obtained. As a result, PP was much more susceptible to thermal decomposition in the presence of silver-exchanged zeolite.Article Citation - WoS: 8Citation - Scopus: 10Moisture Sorption and Thermal Characteristics of Polyaramide Blend Fabrics(John Wiley and Sons Inc., 2006) Genç, Gözde; Alp, Burcu; Balköse, Devrim; Ülkü, Semra; Cireli, AysunFour types of fabrics woven from various polyaramid fibers of Nomex and Kevlar blends were characterized by morphology, XRD, elemental analysis, thermal analysis, and moisture adsorption isotherms. The blends consisted of Polybenzimidazole/ Kevlar blend (40% FBI and 60% Kevlar®), Nomex Delta A (blend of 60% Kevlar and 40% Nomex®), Nomex Delta T (blend of 75% Nomex, 23% Kevlar, and 2% P140 antistatic fiber), and Nomex III (fabric with a 95/5 blend of Nomex and Kevlar) containing 1% steel fiber. TGA and DTG curves have been compared to evaluate thermal behavior of the FBI, Kevlar, and Nomex blends and the resuls were correlated with the moisture sorption data. The data were also compared with fiber morphologies provided by SEM and crystallinities derived from XRD diffrac tograms. Moisture adsorption isotherms were correlated with a number of empirical models, including Nernst, Freundlich, Handersen, Iglesias-Chirife, and with the models having a theoretical background such as Langmuir, BET, GAB, and Hüttig. The linear regression models were statistically analyzed to obtain the best fitting model that explains the sorption profiles of the samples and theoretical monolayer moisture capacities of Nomex and Kevlar blends were calculated by using Hüttig isotherms.