Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
58 results
Filters
Settings
Search Results
Now showing 1 - 10 of 58
Article Citation - WoS: 6Citation - Scopus: 6Experimental and Density Functional Theory Study on Humidity Sensing Properties of Copper Phthalocyanine (cupc)(IOP Publishing, 2019) Farzaneh, Amir; Esrafili, Mehdi D.; Okur, SalihThe quartz crystal microbalance (QCM) technique was applied to investigate humidity sensing properties of a copper phthalocyanine (CuPc) thin film prepared by drop cast method. The humidity adsorption and desorption kinetics of (CuPc) thin film was evaluated. The QCM and electrical measurements results showed that humidity sensing properties of CuPc is very sensitive to humidity changes and reversible adsorption/desorption performance which is an indicative of a good humidity sensor even at room temperature. Reproducible experimental results indicated that CuPc thin films have an abundant potential for humidity sensing applications at ambient temperature. According to the first-principle density functional theory calculations, the promising humidity sensing properties of CuPc can be attributed to the considerable charge transfer from the water molecule into Cu atom.Article Citation - WoS: 2Citation - Scopus: 2Scanning Probe Oxidation Lithography on Ta Thin Films(American Scientific Publishers, 2008) Okur, Salih; Büyükköse, Serkan; Tarı, SüleymanA Semi-Contact Scanning Probe Lithography Technique (SC-SPL) has been applied to create nano-oxide patterns on Ta thin films grown by DC magnetron sputtering method on SiO 2/Si substrates. The height and linewidth profiles of nano-oxide lines created by a conductive AFM tip on Ta film surfaces were measured as a function of applied voltage, oxidation time, humidity, and tip apex curvature. The AFM surface measurements show that the height of the oxides increases linearly with increasing voltage; but there was no oxide growth, when less than 4 V was applied even at 85% relative humidity. Electrical measurements were performed and the resistivities of the TaO x layer and Ta film were obtained as 5.76 × 10 8 and 1.4 × 10 5 Ohm-cm, respectively.Article Citation - WoS: 5Citation - Scopus: 4The Effect of Annealing Temperature on the Optical Properties of a Ruthenium Complex Thin Film(Elsevier Ltd., 2016) Ocakoğlu, Kasım; Okur, Salih; Aydın, Hasan; Emen, Fatih MehmetThe stability of the optical parameters of a ruthenium polypyridyl complex (Ru-PC K314) film under varying annealing temperatures between 278 K and 673 K was investigated. The ruthenium polypyridyl complex thin film was prepared on a quartz substrate by drop casting technique. The transmission of the film was recorded by using Ultraviolet/Visible/Near Infrared spectrophotometer and the optical band gap energy of the as-deposited film was determined around 2.20 eV. The optical parameters such as refractive index, extinction coefficient, and dielectric constant of the film were determined and the annealing effect on these parameters was investigated. The results show that Ru PC K314 film is quite stable up to 595 K, and the rate of the optical band gap energy change was found to be 5.23 × 10- 5 eV/K. Furthermore, the thermal analysis studies were carried out in the range 298-673 K. The Differential Thermal Analysis/Thermal Gravimmetry/Differantial Thermal Gravimmetry curves show that the decomposition is incomplete in the temperature range 298-673 K. Ru-PC K314 is thermally stable up to 387 K. The decomposition starts at 387 K with elimination of functional groups such as CO2, CO molecules and SO3H group was eliminated between 614 K and 666 K.Article Citation - WoS: 4Citation - Scopus: 4Effect of Aromatic Sams Molecules on Graphene/Silicon Schottky Diode Performance(Electrochemical Society, Inc., 2016) Yağmurcukardeş, Nesli; Aydın, Hasan; Can, Mustafa; Yanılmaz, Alper; Mermer, Ömer; Okur, Salih; Selamet, YusufAu/n-Si/Graphene/Au Schottky diodes were fabricated by transferring atmospheric pressure chemical vapor deposited (APCVD) graphene on silicon substrates. Graphene/n-Si interface properties were improved by using 5-[(3-methylphenyl)(phenyl) amino]isophthalic acid (MePIFA) and 5-(diphenyl)amino]isophthalic acid (DPIFA) aromatic self-assembled monolayer (SAM) molecules. The surface morphologies of modified and non-modified films were investigated by atomic force microscopy and scanning electron microscopy. The surface potential characteristics were obtained by Kelvin-probe force microscopy and found as 0.158 V, 0.188 V and 0,383 V as a result of SAMs modification. The ideality factors of n-Si/Graphene, n-Si/MePIFA/Graphene and n-Si/DPIFA/Graphene diodes were found as 1.07, 1.13 and 1.15, respectively. Due to the chain length of aromatic organic MePIFA and DPIFA molecules, also the barrier height φB values of the devices were decreased. While the barrier height of n-Si/Graphene diode was obtained as 0.931 eV, n-Si/MePIFA/Graphene and n-Si/DPIFA/Graphene diodes have barrier height of 0.820 and 0.720 eV, respectively.Article Citation - WoS: 60Citation - Scopus: 66Preparation and Characterization of Calcium Stearate Powders and Films Prepared by Precipitation and Langmuir-Blodgett Techniques(American Chemical Society, 2010) Gönen, Mehmet; Öztürk, Serdar; Balköse, Devrim; Okur, Salih; Ülkü, SemraThe preparation of calcium stearate (CaSt2) using precipitation and Langmuir-Blodgett techniques was investigated in this study. While sodium stearate and calcium chloride were used in the precipitation process, calcium stearate nanofilms were produced from stearic acid and calcium chloride in sodium borate buffer with the Langmuir-Blodgett technique. Fourier transform infrared (FTIR) spectroscopy indicated carboxylate bands at 1577 and 1543 cm-1 in equal intensity in the powder form, but the films had a higher intensity 1577 cm-1 band than the 1543 cm-1 band. This showed the calcium ions associated with the COO- ions in the monodendate and bidendate structures in powders, and it was mainly in the bidendate structure in films. While characteristic peaks of CaSt2 at 2θ values of 6.40° and 19.58° were obtained in the X-ray diffraction (XRD) pattern of the dried powdered product, no sharp peaks were present in the 13 layer CaSt2 film. From scanning electron microscopy (SEM) micrographs, it was seen that calcium stearate powder had lamellar structure and the average particle size was 600 nm. The AFM picture of the CaSt2 film indicated the surface was not smooth with a peak to valley distance of 6 nm. © 2010 American Chemical Society.Article Citation - WoS: 29Citation - Scopus: 31Electrical Properties of Sam-Modified Ito Surface Using Aromatic Small Molecules With Double Bond Carboxylic Acid Groups for Oled Applications(Elsevier Ltd., 2014) Can, Mustafa; Havare, Ali Kemal; Aydın, Hasan; Yağmurcukardeş, Nesli; Demir, Şerafettin; İçli, Sıddık; Okur, Salih5-[(3-Methylphenyl)(phenyl)amino]isophthalic acid (5-MePIFA) and 5-(diphenyl)amino]isophthalic acid (5-DPIFA) organic molecules were synthesized to form self-assembled monolayer on indium tin oxide (ITO) anode to enhance hole transport from ITO to organic hole transport layers such as TPD. The modified surface was characterized by scanning tunneling microscopy (STM). The change in the surface potential was measured by Kelvin probe force microscopy (KPFM). Our Kelvin probe force microscopy (KPFM) measurements showed that the surface potentials increased more than 100 mV with reference to bare indium tin-oxide. The results show that the threshold voltage on OLEDs with modified ITO is lowered significantly compared to OLEDs with unmodified ITO. The hole mobility of TPD has been estimated using space-charge-limited current measurements (SCLC).Article Citation - WoS: 22Citation - Scopus: 24Preparation of the Ferrocene-Substituted 1,3-Distal P-Tert Based Qcm Sensors Array and Utilization of Its Gas-Sensing Affinities(Elsevier Ltd., 2014) Sayın, Serkan; Özbek, Cebrail; Okur, Salih; Yılmaz, MustafaThe article describes the synthesis of the new ferrocene-substituted calix[4]arene derivative 4 as sensitive layer, and suggests that the immobilization of it is on a quartz crystal microbalance gold electrode via the drop-casting method in order to produce the calix[4]arene-based QCM sensor. In addition, sensor response of the calix[4]arene-based QCM sensor was investigated towards carbon dioxide (CO2) and carbon monoxide (CO). The sensing and selectivity studies show that the ferrocene-substituted calix[4]arene-based QCM sensor is an effective gas sensor toward both carbon dioxide and carbon monoxide.Article Citation - WoS: 3Citation - Scopus: 4Electrical Characterization of Interdigitated Humidity Sensors Based on Cnt Modified Calixarene Molecules(Polish Academy of Sciences, 2013) Özbek, Cebrail; Çulcular, Evren; Okur, Salih; Yılmaz, M.; Kurt, M.In this study, we report on the optimization and characterization of chloroform soluble calix[4]arene derivative as a humidity sensor based on electrical properties. Due to the fact that calix[4]arene molecules are nonconductive, we modified the calix[4]arene molecules with carbon nanotubes with electrostatic bond in order to increase the conductance of calix[4]arene molecule (5,11,17,23-tetra-ter-butyl-25,27-dehydrazinamidcarbonilmetoxy-26,28- -dehydroxy-kalix[4]aren). Using photolithography technique, we fabricated interdigitated gold electrodes with 3 micrometers separation to investigate the electrical properties of carbon nanotubes modified calix[4]arene molecule where we used dropcast method to form a thin film of carbon nanotubes modified calix[4]arene molecule on the gold electrodes. Our reproducible experimental results indicated that the chloroform soluble carbon nanotubes modified calix[4]arene films have great potential for humidity sensing applications at room temperature operations.Article Citation - WoS: 3Citation - Scopus: 4Electrical Characterizations of Schottky Diodes on Ito Modified by Aromatic Sams(Polish Academy of Sciences, 2013) Havare, A. Kemal; Okur, Salih; Yağmurcukardeş, Nesli; Can, M.; Aydın, H.; Şeker, M.; Demiç, ŞerafettinIn order to understand the electronic properties of the organic Schottky diode, ITO/TPD/Al and ITO/SAM/ TPD/Al organic Schottky devices were fabricated to obtain currentffvoltage characteristics. From the slopes and y-axis intercepts of the plots, the values of the ideality factor, barrier heights of the ITO/SAM/TPD/Al diode were determined as 2.03 and 0.56 eV, respectively. The surface characterizations of modified and unmodified ITO were performed via atomic force microscopy.Article Citation - WoS: 1Citation - Scopus: 1Improvement of Anode/Htl Interface Properties Using Self-Assembled Monolayer in Organic Electronic Devices(Polish Academy of Sciences, 2013) Yaman, M.; Yağmurcukardeş, Nesli; Havare, A. Kemal; Aydın, H.; Ocakoğlu, Kasım; Okur, SalihFabrication and characterization of highly effcient organic light-emitting diode with surface modification of indium tin oxide anodes by using self-assembled monolayer technique have been studied. Four different self-assembled molecules, K-28 ruthenium complex, octadecylamine hydrochloride, octadecyltrichlorosilane and mercaptohexdecanoic acid are used to modify ITO surface to improve the interface properties. Space charge limited currents measurements have been used to evaluate carrier mobility under steady state current. The results show that the surface properties such as the stability of ITO anode layer have significant effects on charge injection in organic light-emitting diode devices.