Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
Search Results
Now showing 1 - 8 of 8
Article Citation - WoS: 13Citation - Scopus: 14Perspectives of Biomass Catalytic Fast Pyrolysis for Co-Refining: Review and Correlation of Literature Data From Continuously Operated Setups(American Chemical Society, 2022) Prins, Wolter; Yıldız, GürayFor the co-processing of pyrolysis-based biocrudes within petroleum refineries, a degree of conditioning/upgrading involving the cracking of the oligomers and (partial) removal of oxygen could be operationally beneficial. By inducing a complex set of reactions in biomass-derived fast pyrolysis vapors, catalytic fast pyrolysis (CFP) ensures significant changes in oxygen functionalities and alleviates oxygen concentration in the resulting liquid intermediate (CFP-oil). Due to its reduced oxygen content and acidity, CFP-oil could be considered suitable for co-feeding in FCC units and/or for co-hydrotreatment (co-HT) with gas oils within the existing crude oil processing infrastructure. On the operational side, however, research concerning CFP of biomass has shown poor results: deoxygenation of pyrolysis vapors goes along with a progressive reduction in CFP-oil yield. Apart from any control over catalyst activity, selectivity, and lifetime, the other critical issue is in the process design, which is complicated by rapid catalyst deactivation through coke formation and catalyst poisoning by biomass-originated minerals. This review analyzes the outcome of research efforts concerning in- and ex situ CFP of biomass based on carefully selected literature studies reporting the results obtained from meso- and macrolevel laboratory-scale setups, pilot, process development units (PDU), and (semi-) commercial process units, wherein the biomass feedstock and catalyst is fed continuously. Key operational aspects such as the reactor technology, reactive medium, processing mode, and optimization of process parameters are addressed. The performances of continuously operated CFP units were benchmarked through a comparison of yields and elemental compositions of (by-)products. Despite the considerable research efforts related to CFP technology development, the co-processing of CFP-oil is still in its infancy. However, in close collaboration with refinery professionals, it could be made a serious candidate for biobased co-feeding. For refinery integration, quality parameters of CFP-oil, e.g., acidity, stability, and miscibility, should be considered as crucial as its oxygen content.Article Citation - WoS: 9Citation - Scopus: 18Improvement of Photophysical Properties of Cspbbr3 and Mn2+:cspb(br,cl)(3) Perovskite Nanocrystals by Sr2+ Doping for White Light-Emitting Diodes(American Chemical Society, 2022) Yüce, Hürriyet; Mandal, Mukunda; Yalçınkaya, Yenal; Andrienko, Denis; Demir, Mustafa MuammerAll-inorganic metal halide perovskite nanocrystals (NCs) having the general formula ABX(3), where A is a monovalent cation, for example, Cs+, B is a divalent cation, typically Pb2+, and X is Cl-, Br-, I-, or their binary mixture, show potential in optoelectronic devices. In this work, we explore the effect of B-site doping on the optoelectronic properties of CsPbX3 NCs (X = Br, Cl). First, the Pb2+ ions in the pristine CsPbBr3 NC are partially substituted by Mn2+ ions. The alkaline earth metal strontium is then doped on both pristine and the Mn2+-substituted NCs. We found that a small percentage of Sr2+ doping remarkably improves the photoluminescence quantum yield of CsPbBr3 and Mn2+-state emission in Mn2+:CsPb(Br,Cl)(3) NCs. Perovskite NC film/ poly(methyl methacrylate) composites with all four NC variants were used in a white light-emitting diode (WLED), where Sr2+ doping increased the luminous efficiency of the WLED by similar to 4.7%. We attribute this performance enhancement to a reduced defect density and an attenuated microstrain in the local NC structure.Article Citation - WoS: 6Citation - Scopus: 6Tribocorrosion-Resistant Ti40nb-Tin Composites Havingtio(2)-Based Nanotubular Surfaces(American Chemical Society, 2022) Çaha, İhsan; Alves, Alexandra Cruz; Chirico, Caterina; Pinto, Ana Maria; Tsipas, Sophia; Gordo, Elena; Toptan, FatihA novel multifunctional material was developed byhard TiN particle reinforcement addition to a beta-type Ti40Nb alloy,followed by surface functionalization, yielding the formation of ananotubular layer. Corrosion and tribocorrosion behaviors wereinvestigated in a phosphate-buffered saline solution at bodytemperature. The results revealed that the Ti40Nb-TiNcomposites presented similaripassandE(i=0)values together withrelatively similarRoxandCox. However, its tribocorrosion resistancedrastically improved (wear volume is almost 15 times lower than anunreinforced alloy) as a consequence of the load-carrying effectgiven by the reinforcement phases. The corrosion and tribocorro-sion behaviors were further improved through surface functionaliza-tion as observed by significantly loweripassand higherRoxvalues andalmost undetectable wear volume loss from tribocorrosion tests dueto the formation of a well-adhered anatase-rutile TiO2-based nanotubular layer.Article Citation - WoS: 2Citation - Scopus: 2Highly Mobile Excitons in Single Crystal Methylammonium Lead Tribromide Perovskite Microribbons(American Chemical Society, 2022) McClintock, Luke; Song, Ziyi; Travaglini, H. Clark; Senger, Ramazan Tuğrul; Chandrasekaran, Vigneshwaran; Htoon, Han; Yarotski, Dmitry; Yu, DongExcitons are often given negative connotation in solar energy harvesting in part due to their presumed short diffusion lengths. We investigate exciton transport in single-crystal methylammonium lead tribromide (MAPbBr3) microribbons via spectrally, spatially, and temporally resolved photocurrent and photoluminescence measurements. Distinct peaks in the photocurrent spectra unambiguously confirm exciton formation and allow for accurate extraction of the low temperature exciton binding energy (39 meV). Photocurrent decays within a few μm at room temperature, while a gate-tunable long-range photocurrent component appears at lower temperatures (about 100 μm below 140 K). Carrier lifetimes of 1.2 μs or shorter exclude the possibility of the long decay length arising from slow trapped-carrier hopping. Free carrier diffusion is also an unlikely source of the highly nonlocal photocurrent, due to their small fraction at low temperatures. We attribute the long-distance transport to high-mobility excitons, which may open up new opportunities for novel exciton-based photovoltaic applications.Article Citation - WoS: 11Citation - Scopus: 12Colorimetric and Fluorometric Profiling of Advanced Glycation End Products(American Chemical Society, 2022) Ammanath, Gopal; Delachi, Carla Giorgia; Karabacak, Soner; Ali, Yusuf; Boehm, Bernhard O.; Yıldız, Ümit Hakan; Alagappan, Palaniappan; Liedberg, BoProfiling of advanced glycation end products (AGEs) is an emerging area of clinical significance for disease diagnosis and prognosis. Typically, concentrations of AGEs are estimated in laboratories by trained personnel using sophisticated equipment. Herein, a facile approach for colorimetric and fluorometric profiling of AGEs is reported for rapid and on-site analysis. The concentrations of AGE levels in plasma are estimated via changes in optical properties of polythiophenes (PTs) upon interaction with aptamers (Apts) in the presence and in the absence of AGEs. To validate the proposed approach, glyceraldehyde-derived AGEs (AGE class 1 [AGE1]), the biomarker associated with cardiovascular diseases and diabetes, are used as a model system. Colorimetric analysis yielded linear responses for AGE1 for clinically relevant concentration ranges between 1.5 and 300 μg/mL with a limit of detection (LOD) of ∼1.3 μg/mL. Subsequently, an approach utilizing PTs with four different pendant groups in conjunction with four different Apts is demonstrated for qualitative colorimetric profiling and for quantitative fluorometric profiling of up to four AGEs in clinical matrices. Principal component analysis (PCA) of fluorometric responses of AGE-spiked samples yielded distinct responses for the different AGEs tested. Thus, the proposed approach ascertains rapid profiling of spiked AGEs in plasma samples without the requirement of preanalytical processing and advanced instrumentation, thereby facilitating on-site diagnosis.Article Citation - WoS: 7Citation - Scopus: 6L2[gaxfa1–xpbi3]pbi4 (0 ≤ X ≤ 1) Ruddlesden–popper Perovskite Nanocrystals for Solar Cells and Light-Emitting Diodes(American Chemical Society, 2022) Güvenç, Çetin Meriç; Tunç, İlknur; Balcı, SinanThe main challenges to overcome for colloidal 2D Ruddlesden–Popper (RP) organo-lead iodide perovskite nanocrystals (NCs) are phase instability and low photoluminescence quantum yield (PLQY). Herein, we demonstrate colloidal synthesis of guanidinium (GA)-L2[GAPbI3]PbI4, formamidinium (FA)-L2[FAPbI3]PbI4, and GA and FA alloyed L2[GA0.5FA0.5PbI3]PbI4 NCs without using polar or high boiling point nonpolar solvents. Importantly, we show that optical properties and phase stability of L2[APbI3]PbI4 NCs can be affectively tuned by alloying with guanidinium and formamidinium cations. Additionally, the band gap of NCs can be rapidly engineered by bromide ion exchange in L2[GAxFA1–xPbI3]PbI4 (0 ≤ x ≤ 1) NCs. Our approach produces a stable dispersion of L2[FAPbI3]PbI4 NCs with 12.6% PLQY that is at least three times higher than the previously reported PLQY in the nanocrystals. Furthermore, L2[GAPbI3]PbI4 and L2[GA0.5FA0.5PbI3]PbI4 NC films exhibit improved ambient stability over 10 days, which is significantly higher than L2[FAPbI3]PbI4 NC films, which transform to an undesired 1D phase within 6 days. The colloidally synthesized guanidinium- and formamidinium-based 2D RP organo-lead iodide perovskite NCs with improved stability and high PLQY demonstrated in this study may find applications in solar cells and light-emitting diodes. Therefore, large A-site cation-alloyed 2D RP perovskite NCs may provide a new way to rationalize high-performance and stable perovskite solar cells and light-emitting diodes.Article Citation - WoS: 7Citation - Scopus: 7A Perspective on Polythiophenes as Conformation Dependent Optical Reporters for Label-Free Bioanalytics(American Chemical Society, 2022) Sinsinbar, Gaurav; Palaniappan, Alagappan; Yıldız, Ümit Hakan; Liedberg, BoPoly(3-alkylthiophene) (PT)-based conjugated polyelectrolytes (CPEs) constitute an important class of responsive polymers with excellent optical properties. The electrostatic interactions between PTs and target analytes trigger complexation and concomitant conformational changes of the PT backbones that produce distinct optical responses. These conformation-induced optical responses of the PTs enable them to be utilized as reporters for detection of various analytes by employing simple UV-vis spectrophotometry or the naked eye. Numerous PTs with unique pendant groups have been synthesized to tailor their interactions with analytes such as nucleotides, ions, surfactants, proteins, and bacterial and viral pathogens. In this perspective, we discuss PT-target analyte complexation for bioanalytical applications and highlight recent advancements in point-of-care and field deployable assays. Subsequently, we highlight a few areas of critical importance for future applications of PTs as reporters, including (i) design and synthesis of specific PTs to advance the understanding of the mechanisms of interaction with target analytes, (ii) using arrays of PTs and linear discriminant analysis for selective and specific detection of target analytes, (iii) translation of conventional homogeneous solution-based assays into heterogeneous membrane-based assay formats, and finally (iv) the potential of using PT as an alternative to conjugated polymer nanoparticles and dots in bioimaging.Article Citation - WoS: 46Citation - Scopus: 46Thiolene- and Polycaprolactone Methacrylate-Based Polymerized High Internal Phase Emulsion (polyhipe) Scaffolds for Tissue Engineering(American Chemical Society, 2022) Aldemir Dikici, Betül; Malayeri, Atra; Sherborne, Colin; Dikici, Serkan; Paterson, Thomas; Dew, Lindsey; Claeyssens, FrederikHighly porous emulsion templated polymers (PolyHIPEs) provide a number of potential advantages in the fabrication of scaffolds for tissue engineering and regenerative medicine. Porosity enables cell ingrowth and nutrient diffusion within, as well as waste removal from, the scaffold. The properties offered by emulsion templating alone include the provision of high interconnected porosity, and, in combination with additive manufacturing, the opportunity to introduce controlled multiscale porosity to complex or custom structures. However, the majority of monomer systems reported for PolyHIPE preparation are unsuitable for clinical applications as they are nondegradable. Thiol-ene chemistry is a promising route to produce biodegradable photocurable PolyHIPEs for the fabrication of scaffolds using conventional or additive manufacturing methods; however, relatively little research has been reported on this approach. This study reports the groundwork to fabricate thiol- and polycaprolactone (PCL)-based PolyHIPE materials via a photoinitiated thiolene click reaction. Two different formulations, either three-arm PCL methacrylate (3PCLMA) or four-arm PCL methacrylate (4PCLMA) moieties, were used in the PolyHIPE formulation. Biocompatibility of the PolyHIPEs was investigated using human dermal fibroblasts (HDFs) and human osteosarcoma cell line (MG-63) by DNA quantification assay, and developed PolyHIPEs were shown to be capable of supporting cell attachment and viability.