Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection

Permanent URI for this collectionhttps://hdl.handle.net/11147/7148

Browse

Filters

20222

Settings

COAR Access Rights: search.filters.coarAccessRights.embargoed accessSubject: search.filters.subject.Biocompatibility

Search Results

Now showing 1 - 2 of 2
  • Article
    Citation - WoS: 8
    Citation - Scopus: 8
    Design and Fabrication of Polymer Micro/Nano Composites With Two-Level Mechanical Reinforcing Procedure
    (Wiley, 2022) Kandemir, Ayşe Çağıl; Dönmez, Fatma; Davut, Kemal; Kaplan Can, Hatice
    Biocompatible composite production was accomplished by utilizing two-level hierarchical approach for mechanical reinforcement. A well-known commodity polymer; low-density polyethylene (LDPE), which has high-fracture toughness, yet low strength and modulus was used as the main matrix material. As the first step of hierarchy, ductile LDPE was blended with brittle polyvinylpyrrolidone (PVP), which is an eco-friendly, nontoxic and biocompatible polymer. This resulted in slight decrease of strength and drastic reduction of toughness (%70), yet modulus was increased by 78%. As the second level of hierarchy, PVP composites were introduced in LDPE. Nano-scaled Halloysite clay and micro-scaled spherical Silica particles were utilized as additives in the aforementioned PVP composites. The reason for the choice of these particles is that they are nontoxic, low-cost and in the case of Halloysite; abundant in nature. Owing to the implementation of the second level; modulus improvement was further enhanced to 150%, with additional benefits of strength increase up to 17% and less reduction in fracture toughness (minimum 51% reduction). Dynamic mechanical analysis also supported these outcomes that storage modulus of composites are higher than both LDPE and LDPE-PVP blend. The proposed biocompatible composites in the end of this study would be utilized in biomedical applications necessitating mechanical improvements.
  • Article
    Citation - WoS: 46
    Citation - Scopus: 46
    Thiolene- and Polycaprolactone Methacrylate-Based Polymerized High Internal Phase Emulsion (polyhipe) Scaffolds for Tissue Engineering
    (American Chemical Society, 2022) Aldemir Dikici, Betül; Malayeri, Atra; Sherborne, Colin; Dikici, Serkan; Paterson, Thomas; Dew, Lindsey; Claeyssens, Frederik
    Highly porous emulsion templated polymers (PolyHIPEs) provide a number of potential advantages in the fabrication of scaffolds for tissue engineering and regenerative medicine. Porosity enables cell ingrowth and nutrient diffusion within, as well as waste removal from, the scaffold. The properties offered by emulsion templating alone include the provision of high interconnected porosity, and, in combination with additive manufacturing, the opportunity to introduce controlled multiscale porosity to complex or custom structures. However, the majority of monomer systems reported for PolyHIPE preparation are unsuitable for clinical applications as they are nondegradable. Thiol-ene chemistry is a promising route to produce biodegradable photocurable PolyHIPEs for the fabrication of scaffolds using conventional or additive manufacturing methods; however, relatively little research has been reported on this approach. This study reports the groundwork to fabricate thiol- and polycaprolactone (PCL)-based PolyHIPE materials via a photoinitiated thiolene click reaction. Two different formulations, either three-arm PCL methacrylate (3PCLMA) or four-arm PCL methacrylate (4PCLMA) moieties, were used in the PolyHIPE formulation. Biocompatibility of the PolyHIPEs was investigated using human dermal fibroblasts (HDFs) and human osteosarcoma cell line (MG-63) by DNA quantification assay, and developed PolyHIPEs were shown to be capable of supporting cell attachment and viability.