Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
95 results
Search Results
Now showing 1 - 10 of 95
Article Influence of High Content of Sodium Doping in Bi(pb)2212 Superconductors(Pleiades Publishing, 2023) Faiza, Bouaïcha; Mosbah, Mohamed-Fayçal; Özyüzer, LütfiAbstract: We study here, the effect of high content of sodium doping on structural and electrical properties of Bi(Pb)2212 superconductors. The X-ray analysis results showed that all the prepared samples mainly belong to the superconducting tetragonal phase Bi–(Pb)2212. SEM micrographs show that the grains are closely related and have a characteristic flat shape for the superconductor Bi (Pb) 2212. For the undoped sample, the grains are randomly distributed with an average size of 5 μm. For doped samples, the morphology changes with sodium concentration. Resistivity measurements show that all samples have a superconducting character. © 2023, Pleiades Publishing, Ltd.Article Citation - WoS: 3Citation - Scopus: 4Terahertz Wavefront Engineering Using a Hard-Coded Metasurface(Springer, 2023) Noori, Aileen; Akyürek, Bora; Demirhan, Yasemin; Özyüzer, Lütfi; Güven, Kaan; Altan, Hakan; Aygün, GülnurDuring the past few years, coding metamaterials (MM) drew significant attention, where the far-field scattering/transmission pattern of the electromagnetic wave (particularly in the THz regime) can be encoded into a single or few-bit digitized phase-response of the metasurface, thereby enabling a full digital control. Single-bit MMs contain two types of unit cells where the phase becomes 0 and 1 (in units of ?), respectively. By arranging these unit cells into a 2D surface pattern, the THz wavefront can be shaped. In this work, a novel hard-coded metasurface was designed, fabricated, and experimentally investigated for multi-beam reflection of incident THz beam. The design employs stripe and checkerboard patterns of bilayer MM unit cells consisting of square gold patches with a polymer spacing layer from a gold backplane. Experimental and simulation results show that the incident wave in the 0.500–0.750 THz range can be reflected with > 95% efficiency in uniform amplitude and 1-bit coded phase. For the checkerboard metasurface pattern, the measured and analytically calculated reflection angle shows good agreement. The metasurface design is suitable for large-scale fabrication and can potentially be used as a template in the development of actively coded metasurfaces. © 2023, The Author(s), under exclusive licence to Springer Science+Business Media, LLC, part of Springer Nature.Article Citation - WoS: 4Citation - Scopus: 4Development of Single-Use Thin Film Electrodes Based on Zn2sno4 on In2o3:sno2 Substrates With Their Biosensing Applications(Elsevier, 2022) Yurttaş, Betül; Maral, Meltem; Erdem, Arzu; Özyüzer, LütfiDopamine (DA) has a significant impact on the emergence and treatment of certain diseases (e.g., Alzheimer's and Parkinson's diseases). Therefore, monitoring of DA is important, and using biosensors is a favorable option instead of time-consuming and expensive conventional methods. In biosensor manufacturing, thin films have become a rapidly emerging field. In this study, a non-enzymatic electrochemical biosensor based on thin film electrodes is developed for monitoring DA levels. The thin film electrodes (ZTO/ITO) are developed by deposition of Zn2SnO4 (ZTO) on In2O3:SnO2 (ITO) substrates by magnetron sputtering. 3-aminopropyltriethoxysilane (APTES) is used to modify the surface of these electrodes. Physical, optical, and structural properties of the electrodes are determined by applying surface profilometry, UV–VIS–NIR spectrophotometry, X-ray diffraction (XRD), and scanning electron microscopy (SEM) measurements. According to these measurements, it has been observed that the ZTO/ITO combination has a higher optical transmission value than the bare ITO, depending on the deposition time and the oxygen concentration used during ZTO deposition. In addition, the ITO thin film has a crystalline structure, while the ZTO thin film has an amorphous structure and both thin films have a good surface morphology. As electrochemical analysis, cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and differential pulse voltammetry (DPV) measurements are performed. As a result of CV and EIS measurements, a remarkable change (63.54%) was observed after applying APTES modification onto the surface of ZTO/ITO electrode, and the ones obtained by DPV showed successful detection of DA by APTES modified ZTO/ITO. In addition, the experiments in the presence of interferences such as ascorbic acid (AA), uric acid (UA), bovine serum albumin (BSA), and fish sperm double-stranded DNA (fsDNA) show that the electrodes can be successfully applied for voltammetric determination of DA. The detection limit of DA was estimated to be 0.013 µM in the range of DA between 0.1 and 1 µM, and sensitivity was calculated and found to be 11.057 μA μg−1 mL cm−2, which means ZTO/ITO electrodes have a good sensitivity.Article Citation - WoS: 6Citation - Scopus: 5Structural and Optical Characteristics of Antimony Selenosulfide Thin Films Prepared by Two-Step Method(Springer, 2022) Türkoğlu, Fulya; Ekren, Memduh Emirhan; Cantaş, Ayten; Yakıncı, Kübra; Gündoğan, Hazal; Aygün, Gülnur; Özyüzer, LütfiAntimony triselenide (Sb2Se3) is one of the most promising absorber material choices among the inorganic semiconductors that has attracted much attention today. However, highest recorded efficiencies for Sb2Se3 solar cells are still lower than ideal. Exploring antimony selenosulfide (Sb-2(SxSe1-x)(3)) to increase device performance is one option because some features of alloyed Sb-2(SxSe1-x)(3) depend on composition such as bandgap and band position. In this study, two-step process was used to grow Sb-2(SxSe1-x)(3) thin films. In the first stage, Sb2Se3 thin films were deposited on soda lime glass substrates using direct current magnetron sputtering technique. In the second stage, Sb2Se3 thin films were exposed to sulfurization process in a quartz ampoule to obtain Sb-2(SxSe1-x)(3) thin films. Characterization results showed that morphological, optical, and structural properties of Sb-2(SxSe1-x)(3) thin films grown by presented method were highly dependent on amount of sulfur in the films. By the adjustment of the S/S + Se atomic ratio, Sb-2(SxSe1-x)(3) absorber materials with suitable bandgap, favorable orientation and compact morphology can be obtained for photovoltaic applications.Article Citation - WoS: 4Citation - Scopus: 5Enhanced Optoelectronic Properties of Magnetron Sputtered Ito/Ag Multilayers by Electro-Annealing(AVS, 2022) Uyanık, Zemzem; Türkoğlu, Fulya; Köseoğlu, Hasan; Ekmekçioğlu, Merve; Ata, Bengü; Demirhan, Yasemin; Özdemir, Mehtap; Aygün, Gülnur; Özyüzer, LütfiIndium tin oxide/silver/indium tin oxide (ITO/Ag/ITO) multilayers have attracted much attention to fulfill the growing need for high-performance transparent conducting oxide electrodes. To make these transparent multilayers work better, electro-annealing, which is a method of self-heating by electric current, can be effective. Moreover, the effect of current on ITO/Ag/ITO multilayers should be investigated to make sure that electronic devices will be reliable over their lifetime. In this study, ITO/Ag/ITO multilayer electrodes with varying Ag thicknesses were grown by DC magnetron sputtering at room temperature. Structural, optical, and electrical properties of these multilayers were investigated before and after electro-annealing. Measurement results revealed that improved optical transmittance and sheet resistance can be obtained by the optimization of Ag thickness for the as-grown ITO/Ag/ITO layers. The highest figure of merit (FoM) value of 17.37 × 10−3 Ω−1 with optical transmittance of 85.15% in the visible region and sheet resistance of 11.54 Ω/□ was obtained for the Ag thickness of 16.5 nm for as-grown samples. The electro-annealing of as-grown ITO/Ag/ITO multilayers led to improved optical behavior of the multilayer structure over a wide spectral range, especially in the near-infrared range. Electro-annealing also provided an improvement in the crystallinity and sheet resistance of the electrodes. The improvement of the electrical and optical properties of the structure enabled a FoM of 23.07 × 10−3 Ω−1 with the optical transmittance of 86.80% in the visible region and sheet resistance of 10.52 Ω/□. The findings of this work provide proper knowledge of the properties of ITO/Ag/ITO multilayers under electrical current and suggest that the overall performance of the multilayers can be improved by the electro-annealing process.Article Citation - WoS: 8Citation - Scopus: 8Development of Zto/Ag Transparent Electrodes for Thin Film Solar Cells(Springer, 2022) Türkoğlu, Fulya; Köseoğlu, Hasan; Ekmekçioğlu, Merve; Cantaş, Ayten; Özdemir, Mehtap; Aygün, Gülnur; Özyüzer, LütfiThis article presents the optimization of Zinc Tin Oxide/Silver/Zinc Tin Oxide (ZTO/Ag/ZTO) multilayers to implement them in thin film solar cells as transparent electrodes. To achieve improvements on the performance of these transparent multilayers, effect of Ag and ZTO thicknesses, and position of Ag layer within the multilayer were investigated. Electrical and optical characterization of these multilayers revealed that reduced sheet resistance and improved optical transmittance can be acquired for solar cells by the optimization of thin film thicknesses and position of the Ag within the multilayer. The improvement of the electrical and optical behavior of the ZTO/Ag/ZTO structures enabled figure of merit (FoM) values up to 69.69 × 10–3 Ω−1. The performance of our multilayer electrodes was also compared with ITO and AZO electrodes. The obtained results suggest that fabricated multilayer electrodes can be a good choice for thin film solar cells.Conference Object Investigation of In-Gap Field Enhancement at Terahertz Frequencies for a Metasurface Enhanced Sensor(Institute of Electrical and Electronics Engineers, 2021) Tugay, Halime; Altan, Hakan; Demirhan, Yasemin; Özyüzer, Lütfi; Sabah, CumaliThe arrangements of subwavelength inclusions in a metasurface can serve as an effective absorber for the terahertz region. When such an absorber is combined with a unique material, the absorption can induce effects that can lead to a change in the materials electrical properties. Vanadium dioxide shows a passive and reversible change from monoclinic insulator phase to metallic tetragonal rutile structure by using external stimuli such as temperature (340K), photo excitation, electric field, mechanical strain or magnetic field [1,2]. Upon absorption of the THz radiation, the high electric fields that are generated inside the gaps of the metasurface can serve as trigger points, as was shown previously using kV strength THz E-fields.Article Citation - WoS: 33Citation - Scopus: 39High Transparent, Low Surface Resistance Zto/Ag Multilayer Thin Film Electrodes on Glass and Polymer Substrates(Pergamon-Elsevier Science Ltd, 2021) Ekmekçioğlu, Merve; Erdoğan, Nursev; Astarlıoğlu, Aziz Taner; Yiğen, Serap; Aygün, Gülnur; Özyüzer, Lütfi; Özdemir, MehtapZinc tin oxide (ZTO)/Ag/ZTO multilayer thin films were grown by direct current (DC) magnetron sputtering technique at room temperature on soda lime glass (SLG) and different polymer substrates such as polycarbonate (PC) and polyethylene terephthalate (PET) for transparent conductive electrode (TCE) applications. The effect of substrate on the structural, optical and electrical characteristics of ZTO/Ag/ZTO multilayers was investigated. All prepared ZTO/Ag/ZTO films presented amorphous structure as expected from room temperature deposition process and smooth surface quality with very low surface roughness. We found that ZTO/Ag/ZTO multilayer films grown on SLG, PET and PC substrates have very high optical transmission and low surface resistance. Moreover, after ZTO/Ag/ZTO multilayer thin film deposition on polymer substrates, the optical transmission was found to be enhanced because the higher absorption due to Ag layer is compensated by lower reflectance. Our results suggest that ZTO/Ag/ZTO multilayer thin films on any substrate can be a promising alternative to indium tin oxide (ITO) films as a cost-effective, indium-free, flexible and transparent electrode for various applications.Article Citation - WoS: 6Citation - Scopus: 6Nanolitography Based on Electrospun and Etched Nanofibers(Elsevier, 2021) Noori, Aileen; Döğer, Hilal; Demirhan, Yasemin; Özdemir, Mehtap; Özyüzer, Lütfi; Aygün, Gülnur; Sağlam, ÖzgeIn this study, we propose a new type of nanolithography procedure to fabricate orderly patterned metallic nanostructures using the electrohydrodynamic method and the reactive ion etching process. The electrohydrodynamic process parameters were tuned so as to create patterning with precision, and fibers in nanoscale on silver-coated substrates. We also studied reactive ion etching with different durations on the well-patterned samples. The experiments show that applying a voltage of 400 V resulted in straight patterned fibers with a diameter of 208.7 ? 30.3 nm. The statistical analysis on scanning electron microscope (SEM) images showed a significant difference in the diameter of the fibers fabricated at 400 V compared to those at 500 V and 600 V. We also confirm that the etching process has no affect on the fiber diameter. Moreover, electron dispersive X-Ray spectrometer (EDX) results suggest that an etching duration of 7 min is sufficient to remove the silver coating that is not covered with the fibers, and protect the silver nanostructures underneath the fibers. Utilizing a lowcost nanolithography procedure, we obtain the orderly patterned silver nanostructures for possible integration into miniaturized devices.Article Citation - WoS: 2Citation - Scopus: 2In-Situ Thin Film Copper-Copper Thermocompression Bonding for Quantum Cascade Lasers(Springer, 2021) Rouhi, Sina; Özdemir, Mehtap; Ekmekçioğlu, Merve; Yiğen, Serap; Demirhan, Yasemin; Szerling, Anna; Kosiel, Kamil; Kozubal, Maciej; Kruszka, Renata; Prokaryn, Piotr; Ertuğrul, Mehmet; Reno, John L.; Aygün, Gülnur; Özyüzer, LütfiThe choice of metals, bonding conditions and interface purity are critical parameters for the performance of metal-metal bonding quality for quantum cascade lasers (QCLs). Here, we present a novel approach for the thermocompression bonding of Cu-Cu thin films on GaAs-based waveguides without having any oxide phase, contamination or impurities at the interface. We designed a hybrid system in which magnetron sputtering of Ta, thermal evaporation of Cu and Cu-Cu thermocompression bonding processes can be performed sequentially under high vacuum conditions. GaAs/Ta/Cu and Cu/Ta/GaAs structures were thermocompressionally bonded in our in-situ homebuilt bonding system by optimizing the deposition parameters and bonding conditions. The grown thin film and the obtained interfaces were characterized using x-ray diffraction (XRD), scanning electron microscopy (SEM) and energy-dispersive x-ray spectroscopy (EDX) techniques. The optimum Ta and Cu films' thicknesses were found to be about 20 nm and 500 nm, respectively. EDX analysis showed that the Ta thin film interlayer diffused into the Cu structure, providing better adhesivity and rigidity for the bonding. Additionally, no oxidation phases were detected at the interface. The best bonding quality was obtained when heated up to 430 degrees C with an applied pressure of 40 MPa during bonding process.