Civil Engineering / İnşaat Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/13
Browse
9 results
Search Results
Article Citation - WoS: 9Citation - Scopus: 13Analysis of Adhesively Bonded Joints of Laser Surface Treated Composite Primary Components of Aircraft Structures(Elsevier, 2023) Martin, Seçkin; Nuhoğlu, Kaan; Aktaş, Engin; Tanoğlu, Metin; İplikçi, Hande; Barışık, Murat; Yeke, Melisa; Türkdoğan, Ceren; Esenoğlu, Gözde; Dehneliler, SerkanThe performance of the adhesively bonded aerospace structures highly depends on the adhesion strength between the adhesive and adherents, which is affected by, in particular, the condition of the bonding surface. Among the various surface treatment methods, as state of the art, laser surface treatment is a suitable option for the CFRP composite structures to enhance the adhesion performance, adjusting the roughness and surface free energy with relatively minimizing the damage to the fibers. The aim of this study is the validation and evaluation of the adhesive bonding behavior of the laser surface-treated CFRP composite structures, using the finite element technique to perform a conservative prediction of the failure load and damage growth. Such objectives were achieved by executing both experimental and numerical analyses of the secondary bonded CFRP parts using a structural adhesive. In this regard, to complement physical experiments by means of numerical simulation, macro-scale 3D FEA of adhesively bonded Single Lap Joint and Skin-Spar Joint specimens has been developed employing the Cohesive Zone Model (CZM) technique in order to simulate bonding behavior in composite structures especially skin-spar relation in the aircraft wing-box.Article Citation - WoS: 15Citation - Scopus: 17Effects of Nanosecond Laser Ablation Parameters on Surface Modification of Carbon Fiber Reinforced Polymer Composites(SAGE Publications, 2023) Martin, Seçkin; İplikçi, Hande; Barışık, Murat; Türkdoğan, Ceren; Yeke, Melisa; Nuhoğlu, Kaan; Esenoğlu, Gözde; Tanoğlu, Metin; Aktaş, Engin; Dehneliler, Serkan; İriş, Mehmet ErdemRemoval of contaminants and top polymer layer from the surface of carbon-fiber-reinforced polymer (CFRP) composites is critical for high-quality adhesive-joining with direct bonding to the reinforcing fiber constituents. Surface treatment with a laser beam provides selective removal of the polymer matrix without damaging the fibers and increasing the wettability. However, inhomogeneous thermal properties of CFRP make control of laser ablation difficult as the laser energy absorbed by the carbon fibers is converted into heat and transmitted through the fiber structures during the laser operation. In this study, the effect of scanning speed and laser power on nanosecond laser surface treatment was characterized by scanning electron microscope images and wetting angle measurements. Low scanning speeds allowed laser energy to be conducted as thermal energy through the fibers, which resulted in less epoxy matrix removal and substantial thermal damage. Low laser power partially degraded the epoxy the surface while the high power damaged the carbon fibers. For the studied CFRP specimens consisting of unidirectional [45/0/?45/90]2s stacking of carbon/epoxy prepregs (HexPly®-M91), 100 mJ/mm2 generated by 10 m/s scanning speed and 30 W power appeared as optimum processing parameters for the complete removal of epoxy matrix from the top surface with mostly undamaged carbon fibers and super hydrophilic surface condition. © The Author(s) 2023.Article Citation - WoS: 8Citation - Scopus: 8Improving Adhesive Behavior of Fiber Reinforced Composites by Incorporating Electrospun Polyamide-6,6 Nanofibers in Joining Region(SAGE Publications, 2022) Esenoğlu, Gözde; Barışık, Murat; Tanoğlu, Metin; Yeke, Melisa; Türkdoğan, Ceren; İplikçi, Hande; Martin, Seçkin; Nuhoğlu, Kaan; Aktaş, Engin; Dehneliler, Serkan; İriş, Mehmet ErdemAdhesive joining of fiber reinforced polymer (CFRP) composite components is demanded in various industrial applications. However, the joining locations frequently suffer from adhesive bond failure between adhesive and adherent. The aim of the present study is improving bonding behavior of adhesive joints by electrospun nanofiber coatings on the prepreg surfaces that have been used for composite manufacturing. Secondary bonding of woven and unidirectional CFRP parts was selected since this configuration is preferred commonly in aerospace practices. The optimum nanofiber coating with a low average fiber diameter and areal weight density is succeed by studying various solution concentrations and spinning durations of the polyamide-6.6 (PA 66) electrospinning. We obtained homogeneous and beadles nanofiber productions. As a result, an average diameter of 36.50 +/- 12 nm electrospun nanofibers were obtained and coated onto the prepreg surfaces. Prepreg systems with/without PA 66 nanofibers were hot pressed to fabricate the CFRP composite laminates. The single-lap shear test coupons were prepared from the fabricated laminates to examine the effects of PA 66 nanofibers on the mechanical properties of the joint region of the composites. The single-lap shear test results showed that the bonding strength is improved by about 40% with minimal adhesive use due to the presence of the electrospun nanofibers within the joint region. The optical and SEM images of fractured surfaces showed that nanofiber-coated joints exhibited a coherent failure while the bare surfaces underwent adhesive failure. The PA66 nanofibers created better coupling between the adhesive and the composite surface by increasing the surface area and roughness. As a result, electrospun nanofibers turned adhesive failure into cohesive and enhanced the adhesion performance composite joints substantially.Article Citation - WoS: 31Citation - Scopus: 32Development and Analysis of Composite Overwrapped Pressure Vessels for Hydrogen Storage(SAGE Publications, 2021) Kartav, Osman; Kangal, Serkan; Yücetürk, Kutay; Tanoğlu, Metin; Aktaş, Engin; Artem, Hatice SeçilIn this study, composite overwrapped pressure vessels (COPVs) for high-pressure hydrogen storage were designed, modeled by finite element (FE) method, manufactured by filament winding technique and tested for burst pressure. Aluminum 6061-T6 was selected as a metallic liner material. Epoxy impregnated carbon filaments were overwrapped over the liner with a winding angle of +/- 14 degrees to obtain fully overwrapped composite reinforced vessels with non-identical front and back dome layers. The COPVs were loaded with increasing internal pressure up to the burst pressure level. During loading, deformation of the vessels was measured locally with strain gauges. The mechanical performances of COPVs designed with various number of helical, hoop and doily layers were investigated by both experimental and numerical methods. In numerical method, FE analysis containing a simple progressive damage model available in ANSYS software package for the composite section was performed. The results revealed that the FE model provides a good correlation as compared to experimental strain results for the developed COPVs. The burst pressure test results showed that integration of doily layers to the filament winding process resulted with an improvement of the COPVs performance.Article Citation - WoS: 40Citation - Scopus: 37Investigation of Interlayer Hybridization Effect on Burst Pressure Performance of Composite Overwrapped Pressure Vessels With Load-Sharing Metallic Liner(SAGE Publications, 2020) Kangal, Serkan; Kartav, Osman; Tanoğlu, Metin; Aktaş, Engin; Artem, Hatice SeçilIn this study, multi-layered composite overwrapped pressure vessels for high-pressure gaseous storage were designed, modeled by finite element method and manufactured by filament winding technique. 34CrMo4 steel was selected as a load-sharing metallic liner. Glass and carbon filaments were overwrapped on the liner with a winding angle of [+/- 11 degrees/90 degrees(2)](3) to obtain fully overwrapped composite reinforced vessel with non-identical front and back dome endings. The vessels were loaded with increasing internal pressure up to the burst pressure level. The mechanical performances of pressure vessels, (i) fully overwrapped with glass fibers and (ii) with additional two carbon hoop layers on the cylindrical section, were investigated by both experimental and numerical approaches. In numerical approaches, finite element analysis was performed featuring a simple progressive damage model available in ANSYS software package for the composite section. The metal liner was modeled as elastic-plastic material. The results reveal that the finite element model provides a good correlation between experimental and numerical strain results for the vessels, together with the indication of the positive effect on radial deformation of the COPVs due to the composite interlayer hybridization. The constructed model was also able to predict experimental burst pressures within a range of 8%. However, the experimental and finite element analysis results showed that hybridization of hoop layers did not have any significant impact on the burst pressure performance of the vessels. This finding was attributed to the change of load-sharing capacity of composite layers due to the stiffness difference of carbon and glass fibers.Article Citation - WoS: 23Citation - Scopus: 26Experimental and Statistical Analysis of Carbon Fiber/Epoxy Composites Interleaved With Nylon 6,6 Nonwoven Fabric Interlayers(SAGE Publications Inc., 2020) Beylergil, Bertan; Tanoğlu, Metin; Aktaş, EnginThermoplastic interleaving is a promising technique to improve delamination resistance of laminated composites. In this study, plain-weave carbon fiber/epoxy composites were interleaved with nylon 6,6 nonwoven fabrics with an areal weight density of 17 gsm. The carbon fiber/epoxy composite laminates with/without nylon 6,6 nonwoven fabric interlayers were manufactured by VARTM technique. Double cantilever beam fracture toughness tests were carried out on the prepared composite test specimens in accordance with ASTM 5528 standard. The experimental test data were statistically analyzed by two-parameter Weibull distribution. The results showed that the initiation and propagation fracture toughness Mode-I fracture toughness of carbon fiber/epoxy composites could be improved by about 34 and 156% (corresponding to a reliability level of 0.50) with the incorporation of nylon 6,6 interlayers in the interlaminar region, respectively. The results also revealed that the percent increase in the propagation fracture toughness value was 67 and 41% at reliability levels of 0.90 and 0.95, respectively.Article Citation - WoS: 108Citation - Scopus: 117Enhancement of Interlaminar Fracture Toughness of Carbon Fiber–epoxy Composites Using Polyamide-6,6 Electrospun Nanofibers(John Wiley and Sons Inc., 2017) Beylergil, Bertan; Tanoğlu, Metin; Aktaş, EnginIn this study, carbon fiber–epoxy composites are interleaved with electrospun polyamide-6,6 (PA 66) nanofibers to improve their Mode-I fracture toughness. These nanofibers are directly deposited onto carbon fabrics before composite manufacturing via vacuum infusion. Three-point bending, tensile, compression, interlaminar shear strength, Charpy impact, and double cantilever beam tests are performed on the reference and PA 66 interleaved specimens to evaluate the effects of PA 66 nanofibers on the mechanical properties of composites. To investigate the effect of nanofiber areal weight density (AWD), nanointerlayers with various AWD are prepared by changing the electrospinning duration. It is found that the electrospun PA 66 nanofibers are very effective in improving Mode-I toughness and impact resistance, compressive strength, flexural modulus, and strength of the composites. However, these nanofibers cause a decrease in the tensile strength of the composites. The glass-transition temperature of the composites is not affected by the addition of PA 66 nanofibers. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017, 134, 45244.Article Citation - WoS: 31Citation - Scopus: 36Mechanical Behavior of Polypropylene-Based Honeycomb-Core Composite Sandwich Structures(SAGE Publications Inc., 2010) Sezgin, Fatma Erinç; Tanoğlu, Metin; Eğilmez, Oğuz Özgür; Dönmez, CemalettinThis article presents results from an experimental study, investigating the effects of core thickness on the mechanical properties of composite sandwich structures with polypropylene(PP)-based honeycomb core and glass fiber-reinforced polymer (GFRP) face-sheets fabricated by hand lay-up technique. Epoxy matrix and non-crimp glass fibers were used for the production of GFRP laminates. Flatwise compression (FC), edgewise compression (EC), three-point bending (3PB) and double cantilever beam (DCB) tests were performed to evaluate the mechanical behavior of the composite sandwich structures (CSSs). Based on the FC tests, an increase in the compressive modulus and strength was observed with an increase in the core thickness. For EC tests, peak loads up to crush of the sandwich panel is discussed using core thickness. According to the 3PB tests, a decrease in core shear stress and facesheet bending stress was observed as the core thickness increases. © SAGE Publications 2010.Article Citation - WoS: 53Citation - Scopus: 63Artificial Neural Network (ann) Prediction of Compressive Strength of Vartm Processed Polymer Composites(Elsevier Ltd., 2005) Seyhan, Abdullah Tuğrul; Tayfur, Gökmen; Karakurt, Murat; Tanoğlu, MetinA three layer feed forward artificial neural network (ANN) model having three input neurons, one output neuron and two hidden neurons was developed to predict the ply-lay up compressive strength of VARTM processed E-glass/ polyester composites. The composites were manufactured using fabric preforms consolidated with 0, 3 and 6 wt.% of thermoplastic binder. The learning of ANN was accomplished by a backpropagation algorithm. A good agreement between the measured and the predicted values was obtained. Testing of the model was done within low average error levels of 3.28%. Furthermore, the predictions of ANN model were compared with those obtained from a multi-linear regression (MLR) model. It was found that ANN model has better predictions than MLR model for the experimental data. Also, the ANN model was subjected to a sensitivity analysis to obtain its response. As a result, the ANN model was found to have an ability to yield a desired level of ply-lay up compressive strength values for the composites processed with the addition of the thermoplastic binder.