Civil Engineering / İnşaat Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/13
Browse
14 results
Search Results
Article Citation - WoS: 2Citation - Scopus: 2Numerical Simulation of Flow and Dam Body Sediment Over a Movable Bed Due To an Earthfill Dam Break(Yıldız Teknik Üniversitesi, 2022) Tayfur, Gökmen; Issakhov, Alibek; Zhandaulet, YeldosThis paper presents the numerical simulations of flow and dam body sediment transport over a movable bed due to an earthfill dam break. The RANS equations, together with the k-omega SST turbulent model, are employed. The phase characteristic parameter is used as the phases of air, water, sediment, and bulk of dam body. The system of equations is solved numerically using the PISO algorithm. The numerical model is first verified using the dam break experimental data from the literature. The model successfully captures the temporal changes in the measured flow depths, pressures, wave fronts, and arrival times. The ve rified mod el is then app lied to simulate the flow and sediment transport as a result of an artificial earthfill dam break having an obstacle at its downstream section. The simulations show that there is a noticeable decrease in the shock pressures at all points around the obstacle and there is an increase in the water levels. The bulk dam body sediment moves together with the water flow wh ile sp reading. It takes longer time for the sediment laden flow to reach the obstacle. The investigation of dam body formed by different soils shows that the soil type has minor effect while the transport of sediment can raise the water levels and change the morphology of the downstream section.Conference Object Citation - Scopus: 3Seismic Performance of Cfrp Jacketed Sub-Standard Rc Columns Under High Axial Stress and Shear Demand(Springer, 2022) Demir, Merve Nur; Demir, Uğur; Demir, Cem; İlki, AlperIn the last decades, lessons learnt from the major earthquakes, that occurred in many countries, brought revisions in prevailing seismic design codes. As a consequence of this phenomenon, the current building stock in Turkey is mainly comprised of reinforced concrete (RC) buildings which were designed according to different seismic design codes. The presented paper is a component of a comprehensive investigation which containing three variables i) high axial load ratio defined as axial load divided by the axial capacity, ii) high shear demand defined as the ratio of shear demand at flexural yielding to shear resistance and iii) low transverse reinforcement ratio owing to large spacing among steel reinforcements. Thus, a total of four full-scale square RC columns comprised of i) one column designed to comply with the former Turkish Seismic Design Code (TSDC, 1975) and ii) three columns which are not compliant to any design codes (referred as sub-standard), were tested under high axial load ratio, 0.4 for code-conforming and 0.75 for sub-standard columns, combined with reversed cyclic lateral loading. The columns were also designed to have high shear demand in the order of 0.62 and 0.80 for bare sub-standard according to ACI 318 (2019) and TBEC (2018) design codes as sometimes observed in existing sub-standard structures. In addition to that, the ratio of shear demand for the code-conforming column is calculated 0.43 and 0.50 as per design codes, respectively. Besides, the ratio of transverse reinforcement area to the minimum required transverse reinforcement area was 0.19 and 0.77 for sub-standard columns according to ACI 318 (2019) and TBEC (2018), respectively. For the code-conforming column, the aforementioned ratio was 0.57 and 1.32 for both design codes, in the same manner. One of the sub-standard columns was kept as a reference column while the other two of them have been externally jacketed with one layer or two layers of carbon fiber-reinforced polymer (CFRP) sheets. Test results pointed out that the confinement provided by CFRP jacketing has remarkably improved the performance of seismically-deficient RC columns subjected to high axial compression under high shear demand in terms of lateral load capacity and ductility. The experimental results were also supplemented with theoretical work to evaluate the effects of CFRP jacketing on the seismic behavior of sub-standard RC columns.Conference Object Citation - WoS: 1Citation - Scopus: 2Seismic Performance of Substandard Rc Columns Retrofitted With Sprayed Gfrm(Springer, 2022) Kian, Nima; Demir, Uğur; Demir, Cem; Maraşlı, Muhammed; İlki, AlperThere is a myriad amount of substandard reinforced concrete (RC) buildings in developing countries that do not comply with the requirements and instructions of the current building design codes. In particular, columns in these substandard buildings demonstrate unsatisfactory and undesired behavior against lateral loads, mainly due to low concrete compressive strength and poor reinforcement detailing. The problem is exacerbated when the axial load ratio (ratio of applied axial load to the axial load capacity) and/or the shear ratio (ratio of shear force corresponding to moment capacity (Ve) to the shear capacity (Vr)) is/are high, leading to brittle failure modes. In this study, three full-scale substandard RC columns subjected to high axial load ratio of 0.75 were tested under constant axial load combined with reversed cyclic lateral displacements. Shear ratio (Ve/Vr) of the substandard columns were 0.75 and 0.82 according to ACI 318-19 (ACI 318 (2019) Building Code Requirements for Structural Concrete. American Concrete Institute, Farmington Hills, MI, USA) and (Turkish Building Earthquake Code (Turkish Building Earthquake Code (TBEC) (2018) Disaster & Emergency Management Authority, Ankara, Turkey), respectively. According to the TBEC (Turkish Building Earthquake Code (TBEC) (2018) Disaster & Emergency Management Authority, Ankara, Turkey), columns had a high Ve/(fctmbd) ratio of 1.12, where, fctm, b, and d are the direct tensile strength of concrete, width of the cross-section, and effective depth of the section. The ratio of transverse reinforcement to minimum required transverse reinforcement according to the ACI 318-19 (ACI 318 (2019) Building Code Requirements for Structural Concrete. American Concrete Institute, Farmington Hills, MI, USA) and TBEC (Turkish Building Earthquake Code (TBEC) (2018) Disaster & Emergency Management Authority, Ankara, Turkey) was 0.19 and 0.77, respectively. Two of the columns were retrofitted with an innovative, cost-effective, and easily-applicable strengthening method, through external jacketing with sprayed glass fiber reinforced mortar (GFRM) of different characteristics. The remaining column was tested as the reference specimen to evaluate the efficiency of the strengthening method. The test results demonstrated the extremely poor performance of the reference substandard column as well as the remarkable lateral load capacity and ductility improvement provided by the adopted novel strengthening approach.Conference Object Experimental Investigation of the Stabilization Performance of Geogrids for Unpaved Roads with Low Bearing Capacity Subgrade(Springer International Publishing AG, 2022) Gokova, Suleyman; Saltan, Mehmet; Terzi, Serdal; Tutumluer, Erol; Uz, Volkan Emre; Karasahin, MustafaIn this study, laboratory experiments were carried out on real sized samples to investigate the reinforcement performance of geogrids in highway pavements constructed on low bearing capacity subgrade (California Bearing Ratio, CBR = 3%). In all prepared samples, Hot Mix Asphalt (HMA) layer was not applied. A moving wheel load was applied with Accelerated Pavement Tester (APT) device on representative pavement samples with and without geogrids. Two types of geogrids were used to construct the pavement sample configurations. Resistance to plastic (permanent) deformation was recorded as a performance indicator to compare structural performance trends of the pavement samples. For this objective, surface deformations were measured after certain wheel load repetitions. Rut depths have been calculated from surface profiles measured with a laser profiler and were plotted versus number of load repetitions. As a result of this study, the use of geogrid over soft subgrade with lowCBR values has been shown to extend the life of the pavement by reducing the rut depth.Conference Object Citation - WoS: 2Citation - Scopus: 3Micromechanical Modeling of Inter-Granular Localization, Damage and Fracture(Elsevier, 2018) Yalçınkaya, Tuncay; Özdemir, İzzet; Fırat, Ali Osman; Tandoğan, İzzet TarıkThe recent developments in the production of miniaturized devices increases the demand on micro-components where the thickness ranges from tens to hundreds of microns. Various challenges, such as size effect and stress concentrations at the grain boundaries, arise due to the deformation heterogeneity observed at grain scale. Various metallic alloys, e.g. aluminum, exhibit substantial localization and stress concentration at the grain boundaries. In this regard, inter-granular damage evolution, crack initiation and propagation becomes an important failure mechanism at this length scale. Crystal plasticity approach captures intrinsically the heterogeneity developing due to grain orientation mismatch. However, the commonly used local versions do not possess a specific GB model and leads to jumps at the boundaries. Therefore, a more physical treatment of grain boundaries is needed. For this purpose, in this work, the Gurtin GB model (Gurtin (2008)) is incorporated into a strain gradient crystal plasticity framework (Yalcinkaya et al. (2011), Yalcinkaya et al. (2012), Yalcinkaya (2017)), where the intensity of the localization and stress concentration could be modelled considering the effect of grain boundary orientation, the mismatch and the strength of the GB. A zero thickness 12-node interface element for the integration of the grain boundary contribution and a 10-node coupled finite element for the bulk response are developed and implemented in Abaqus software as user element subroutines. 3D grain microstructure is created through Voronoi tessellation and the interface elements are automatically inserted between grains. After obtaining the localization, the mechanical behavior of the GB is modelled through incorporation of a potential based cohesive zone model (see Park et al. (2009), Cerrone et al. (2014)). The numerical examples present the performance of the developed tool for the intrinsic localization, crack initiation and propagation in micron-sized specimens. (C) 2018 The Authors. Published by Elsevier B.V.Article Citation - WoS: 7Citation - Scopus: 8Enrichment of Trace Element Concentrations in Coal and Its Combustion Residues and Their Potential Environmental and Human Health Impact: Can Coal Basin, Nw Turkey as a Case Study(Inderscience Enterprises, 2016) Baba, Alper; Gürdal, Gülbin; Şanlıyüksel Yücel, DenizIn this study, the variation of trace element concentrations ( total of 48 trace elements including rare earth elements) in coal, coal ash and fly ash were examined and compared with coal Clarke values. Results showed that the average concentrations of trace elements including As, B, Cu, Ce, Co, Cs, Gd, Hf, La, Lu, Mo, Nd, Nb, Pr, Pb, Sc, Sm, Ta, Tb, Th, U, V, W, Y, Yb, Zn and Zr in the Can Basin coals are higher than their respective Clarke values for world low-rank coals. The elements As, Cu, Co, Cs, Mo, Nb, Sc, Pb, Pr, Th, U, V, Zn and Zr are enriched in coal ashes, whereas As, Co, Nb, Sc, U and V are enriched in fly ashes. Among the elements, maximum enrichment in coal was observed for As, with the average concentration of 253.5 ppm As in the Can Basin coals, while the coal Clarke value is 14 ppm and world average value is 8.3 ppm. From the ecotoxicological point of view, combustion residues formed by indoor combustion of coal and/or in thermal power plants may be a hazard to the environment and to aquatic and terrestrial life including human beings, particularly As, trace elements and released radioactive elements.Conference Object Citation - WoS: 1Citation - Scopus: 2Three Dimensional Grain Boundary Modeling in Polycrystalline Plasticity(American Institute of Physics, 2018) Yalçınkaya, Tuncay; Özdemir, İzzet; Fırat, Ali OsmanAt grain scale, polycrystalline materials develop heterogeneous plastic deformation fields, localizations and stress concentrations due to variation of grain orientations, geometries and defects. Development of inter-granular stresses due to misorientation are crucial for a range of grain boundary (GB) related failure mechanisms, such as stress corrosion cracking (SCC) and fatigue cracking. Local crystal plasticity finite element modelling of polycrystalline metals at micron scale results in stress jumps at the grain boundaries. Moreover, the concepts such as the transmission of dislocations between grains and strength of the grain boundaries are not included in the modelling. The higher order strain gradient crystal plasticity modelling approaches offer the possibility of defining grain boundary conditions. However, these conditions are mostly not dependent on misorientation of grains and can define only extreme cases. For a proper definition of grain boundary behavior in plasticity, a model for grain boundary behavior should be incorporated into the plasticity framework. In this context, a particular grain boundary model ([l]) is incorporated into a strain gradient crystal plasticity framework ([2]). In a 3-D setting, both bulk and grain boundary models are implemented as user-defined elements in Abaqus. The strain gradient crystal plasticity model works in the bulk elements and considers displacements and plastic slips as degree of freedoms. Interface elements model the plastic slip behavior, yet they do not possess any kind of mechanical cohesive behavior. The physical aspects of grain boundaries and the performance of the model are addressed through numerical examples.Conference Object Citation - WoS: 1Development of a Proper Mix-Design for Impact Loading of Deflection Hardening Hybrid Fiber Reinforced Concrete(Springer Verlag, 2018) Alami, Muhammad Musa; Erdem, Tahir Kemal; Yardımcı, Mert Yücel; Aydın, SerdarThis study aims to develop a low-cost Hybrid Fiber Reinforced Concrete (HyFRC) that exhibits deflection hardening behavior under bending and has high energy absorption capacity under impact loading by determining proper combination of steel and polyvinyl alcohol (PVA) fibers. More than forty mixtures were prepared including two mixtures of conventional concrete, six mixtures of Engineered Cementitious Composites (ECC), and thirty-six mixtures of HyFRC. The design parameters were chosen as fly ash to cement ratio (1.2, 1.7 and 2.2), steel fiber type and amount (0.5%, 0.75%, and 1.25% by volume), PVA fiber amount (0.25% and 0.50% by volume), and maximum aggregate size (Dmax) of 8 mm and 16 mm. Several tests were carried out on fresh and hardened specimens such as bending, compression, and low-velocity flexural impact loading. Based on the results, it is found that the mixture with 0.75% steel fiber and 0.25% PVA showed the best performance for the aim of the study.Article Citation - WoS: 11Citation - Scopus: 12Cement Based Strain Sensor: a Step To Smart Concrete(Foundation Cement, Lime, Concrete, 2011) Teomete, Egemen; Erdem, Tahir KemalAccording to a report published in USA, 30% of the bridges in USA were found to be structurally de cient while concrete infrastructures have a state of material deterioration before the design life is reached (1). Earthquakes, material degradations and other environmental effects decrease the performance of the structures. The assessment of structures by structural health monitoring is very important to protect the lives of people. The best decision about a damaged structure after an earthquake can be made by use of structural tests and structural health monitoring. Structural tests and structural health monitoring are important steps in the decision making of asset management for maintenance and repair of infrastructures. The classical sensors (strain gauges, piezo-electric sensors) have low durability, low sensitivity and high cost. The low durability of classical sensors disables long term measurement while their high cost limits the amount of sensors that can be used (2). The addition of carbon ber to cement based material decreases the electrical resistance of the material. By application of load, the electrical resistance of the material changes (3-5).Article Citation - WoS: 5Citation - Scopus: 7Experimental and Modeling Study of Strength of High Strength Concrete Containing Binary and Ternary Binders(Foundation Cement, Lime, Concrete, 2011) Erdem, Tahir Kemal; Tayfur, Gökmen; Kırca, ÖnderSilica fume (SF), fl y ash (FA) and ground granulated blastfurnace slag (S) are among the most widely utilized mineral additions for normal strength concrete (NSC) and high strength concrete (HSC). High Reactivity Metakaolin (HRMK) is a relatively new mineral addition, produced by calcination of highly pure kaolin. The replacement of cement with HRMK increases the strength, especially at early ages, and improves durability of concrete. (1-3). Pumice (P) is a porous volcanic glass containing 60-75 SiO2% and 13-17% Al2O3. When fi nely ground, it shows pozzolanic characteristics but it is generally used as a lightweight aggregate in the concrete industry (4, 5). HRMK and P have white color and, therefore, are useful for production of white concrete when applied with white Portland cement (WPC)