Civil Engineering / İnşaat Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/13
Browse
3 results
Search Results
Article Citation - WoS: 60Citation - Scopus: 69Experimental and Numerical Investigation of Bed-Load Transport Under Unsteady Flows(American Society of Civil Engineers (ASCE), 2011) Bombar, Gökçen; Elçi, Şebnem; Elçi, Şebnem; Güney, M. Şükrü; Tayfur, Gökmen; 03.03. Department of Civil Engineering; 03. Faculty of Engineering; 01. Izmir Institute of TechnologyThe dynamic behavior of bed-load sediment transport under unsteady flow conditions is experimentally and numerically investigated. A series of experiments are conducted in a rectangular flume (18 m in length, 0.80 m in width) with various triangular and trapezoidal shaped hydrographs. The flume bed of 8 cm in height consists of scraped uniform small gravel of D 50=4.8 mm. Analysis of the experimental results showed that bed-load transport rates followed the temporal variation of the triangular and trapezoidal hydrographs with a time lag on the average of 11 and 30 s, respectively. The experimental data were also qualitatively investigated employing the unsteady-flow parameter and total flow work index. The analysis results revealed that total yield increased exponentially with the total flow work. An original expression which is based on the net acceleration concept was proposed for the unsteadiness parameter. Analysis of the results then revealed that the total yield increased exponentially with the increase in the value of the proposed unsteadiness parameter. Further analysis of the experimental results revealed that total flow work has an inverse exponential variation relation with the lag time. A one-dimensional numerical model that employs the governing equations for the conservation of mass for water and sediment and the momentum was also developed to simulate the experimental results. The momentum equation was approximated by the diffusion wave approach, and the kinematic wave theory approach was employed to relate the bed sediment flux to the sediment concentration. The model successfully simulated measured sedimentographs. It predicted sediment yield, on the average, with errors of 7% and 15% of peak loads for the triangular and trapezoidal hydrograph experiments, respectively.Article Citation - WoS: 10Citation - Scopus: 14Numerical Model for Sediment Transport Over Nonplanar, Nonhomogeneous Surfaces(American Society of Civil Engineers (ASCE), 2004) Tayfur, Gökmen; Tayfur, Gökmen; 03.03. Department of Civil Engineering; 03. Faculty of Engineering; 01. Izmir Institute of TechnologySediment transport on surfaces with spatially variable microtopography, roughness, and infiltration was investigated using the diffusion wave equation. An implicit finite-difference scheme together with multivariate Newton's method was employed to solve the equation numerically. The simulation results showed that microtopography and roughness were the dominant factors causing significant spatial variations in sediment concentration. If the spatially varying microtopography was replaced by an average constant slope, the result was an overestimation of the sediment load. On the other hand, when the spatially varying roughness was replaced by the average roughness and the spatially varying infiltration rate by the average infiltration rate, the sediment discharge was not significantly affected. The sedimentograph reached an equilibrium much sooner when a constant infiltration rate was substituted for the time-varying infiltration rate.Article Citation - WoS: 36Citation - Scopus: 43Applicability of Sediment Transport Capacity Models for Nonsteady State Erosion From Steep Slopes(American Society of Civil Engineers (ASCE), 2002) Tayfur, Gökmen; Tayfur, Gökmen; 03.03. Department of Civil Engineering; 03. Faculty of Engineering; 01. Izmir Institute of TechnologyThe physics-based sediment transport equations are derived from the assumption that the sediment transport rate can be determined by a dominant variable such as flow discharge, flow velocity, slope, shear stress, stream power, and unit stream power. In modeling of sheet erosion/sediment transport, many models that determine the transport capacity by one of these dominant variables have been developed. The developed models mostly simulate steady-state sheet erosion. Few models that are based on the shear-stress approach attempt to simulate nonsteady state sheet erosion. This study qualitatively investigates the applicability of the transport capacity models that are based on one of the commonly employed dominant variables-unit stream power, stream power, and shear stress-to simulate nonsteady state sediment loads from steep slopes under different rainfall intensities. The test of the calibrated models with observed data sets shows that the unit stream power model gives better simulation of sediment loads from mild slopes. The stream power and the shear stress models, on the other hand, simulate sediment loads from steep slopes more satisfactorily. The exponent (ki) in the sediment transport capacity formula is found to be 1.2, 1.9, and 1.6 for the stream power model, the shear stress model, and the unit stream power model, respectively.