Civil Engineering / İnşaat Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/13
Browse
10 results
Search Results
Now showing 1 - 10 of 10
Article Poliamid 6/6 (pa 66) Mikrofiberler ile Toklaştırılmış Tabakalı Kompozitlerin Mod-ı Delaminasyon Direncinin İstatiksel Analizi(Niğde Ömer Halisdemir Üniversitesi, 2019) Beylergil, Bertan; Tanoğlu, Metin; Aktaş, EnginFiber takviyeli kompozitler, ağırlıklarına oranla yüksek mukavemet ve rijitlikleri nedeniyle uzay ve otomotiv yapısal parçalarında yaygın olarak kullanılmaktadır. Delaminasyon, bu kompozitlerde görülen en yaygın ve kritik hasar modudur. Bu kompozitlerin delaminasyon direncini arttırmak amacıyla, nanokatkılar ile epoksi toklaştırması, dikişleme, z-pimler ve arayüzeyde mikro/nanofiber kullanılması gibi pek çok sayıda teknik geliştirilmiştir. Bu çalışmada, poliamid 6/6 (PA 66) mikrofiberler ile toklaştırılmış karbon fiber/epoksi kompozitlerin Mode-I delaminasyon direnci Weibull dağılımı kullanılarak istatiksel olarak analiz edilmiştir. Test verilerinin istatiksel olarak değerlendirilmesi sonucunda PA 66 mikrofiberlerin kullanılmasının %90 güven seviyesinde kırılma tokluğunu yaklaşık %445 mertebesinde arttırdığı gözlemlenmiştir.Article Citation - WoS: 40Citation - Scopus: 37Investigation of Interlayer Hybridization Effect on Burst Pressure Performance of Composite Overwrapped Pressure Vessels With Load-Sharing Metallic Liner(SAGE Publications, 2020) Kangal, Serkan; Kartav, Osman; Tanoğlu, Metin; Aktaş, Engin; Artem, Hatice SeçilIn this study, multi-layered composite overwrapped pressure vessels for high-pressure gaseous storage were designed, modeled by finite element method and manufactured by filament winding technique. 34CrMo4 steel was selected as a load-sharing metallic liner. Glass and carbon filaments were overwrapped on the liner with a winding angle of [+/- 11 degrees/90 degrees(2)](3) to obtain fully overwrapped composite reinforced vessel with non-identical front and back dome endings. The vessels were loaded with increasing internal pressure up to the burst pressure level. The mechanical performances of pressure vessels, (i) fully overwrapped with glass fibers and (ii) with additional two carbon hoop layers on the cylindrical section, were investigated by both experimental and numerical approaches. In numerical approaches, finite element analysis was performed featuring a simple progressive damage model available in ANSYS software package for the composite section. The metal liner was modeled as elastic-plastic material. The results reveal that the finite element model provides a good correlation between experimental and numerical strain results for the vessels, together with the indication of the positive effect on radial deformation of the COPVs due to the composite interlayer hybridization. The constructed model was also able to predict experimental burst pressures within a range of 8%. However, the experimental and finite element analysis results showed that hybridization of hoop layers did not have any significant impact on the burst pressure performance of the vessels. This finding was attributed to the change of load-sharing capacity of composite layers due to the stiffness difference of carbon and glass fibers.Article Citation - WoS: 8Citation - Scopus: 9Dynamic Behavior Predictions of Fiber-Metal Laminate/Aluminum Foam Sandwiches Under Various Explosive Weights(SAGE Publications, 2016) Baştürk, Suat Bahar; Tanoğlu, Metin; Çankaya, Mehmet Alper; Eğilmez, Oğuz ÖzgürApplication of blast tests causes some problems to characterize the performance of panels due to the drastic conditions of explosive medium. Real test has high safety concerns and is not easily accessible because of its extra budget. Some approaches are needed for the preliminary predictions of dynamic characteristics of panels under blast loading conditions. In this study, the response of sandwiches under blast effect was evaluated by combining quasi-static experiments and computational blast test data. The primary aim is to relate the quasi-static panel analysis to dynamic blast load. Based on this idea, lightweight sandwich composites were subjected to quasi-static compression loading with a special test apparatus and the samples were assumed as single degree-of-freedom mass-spring systems to include dynamic effect. This approach provides a simpler way to simulate the blast loading over the surface of the panels and reveals the possible failure mechanisms without applying any explosives. Therefore the design of the panels can be revised by considering quasi-static test results. In this work, the peak deflections and survivabilities of sandwiches for various explosive weights were predicted based on the formulations reported in the literature. Major failure types were also identified and evaluated with respect to their thicknesses.Article Citation - WoS: 16Citation - Scopus: 24Developing Polymer Composite-Based Leaf Spring Systems for Automotive Industry(Walter de Gruyter GmbH, 2018) Öztoprak, Nahit; Güneş, Mehmet Deniz; Tanoğlu, Metin; Aktaş, Engin; Eğilmez, Oğuz Özgür; Şenocak, Çiler; Kulaç, GedizComposite-based mono-leaf spring systems were designed and manufactured to replace existing mono-leaf metal leaf spring in a light commercial vehicle. In this study, experimentally obtained mechanical properties of different fiber-reinforced polymer materials are presented first, followed by the description of the finite element analytical model created in Abaqus 6.12-1 (Dassault Systemes Simulia Corp., RI, US) using the obtained properties. The results from the finite element analysis are presented next and compared with actual size experimental tests conducted on manufactured prototypes. The results demonstrated that the reinforcement type and orientation dramatically influenced the spring rate. The prototypes showed significant weight reduction of about 80% with improved mechanical properties. The hybrid composite systems can be utilized for composite-based leaf springs with considerable mechanical performance.Conference Object Citation - Scopus: 1Development of Composite Drive Shaft Tube for Automotive Industry(Applied Mechanics Laboratory, 2019) Arslan Özgen, Gizem; Tanoğlu, Metin; Aktaş, Engin; Yücetürk, KutayWeight, vibration, fatigue, and critical speed limitations have been recognized as serious problems in drive shafts in automotive industry for many years. Conventional drive shaft is made up into two parts to increase its fundamental natural bending frequency. This present work deals with the replacement of conventional steel drive shaft with a composite counterparts. The benefits of eliminating the two piece shafts are significant reductions in weight, noise, vibration and harshness. In this work, one-piece propeller shaft composed of carbon/epoxy and glass/epoxy composites have been designed and manufactured for a rear wheel drive automobile. The performance measures are static torque transmission capability, torsional buckling and the fundamental natural bending frequency. The tubular composite shaft samples are being manufactured by using filament winding technique. To predict the torsional properties, fatigue life and failure modes of composite tubes for different fiber orientation angle and stacking sequence, finite element analysis (FEA) has been used. The predicted and experimental values has been reported for comparison. The next phase of work consists of optimization of shaft for the objective function as weight and fundamental natural frequency considering different stacking sequence and fiber orientation. © CCM 2020 - 18th European Conference on Composite Materials. All rights reserved.Article Citation - WoS: 97Citation - Scopus: 110Effect of Polyamide-6,6 (pa 66) Nonwoven Veils on the Mechanical Performance of Carbon Fiber/Epoxy Composites(Elsevier Ltd., 2018) Beylergil, Bertan; Tanoğlu, Metin; Aktaş, EnginIn this study, carbon fiber/epoxy (CF/EP) composites were interleaved with polyamide-6,6 (PA 66) nonwoven veils at two different areal weight densities (17 and 50 gsm) to improve their delamination resistance against Mode-I loading. Mode-I fracture toughness (DCB), tensile, open hole tensile (OHT), flexural, compression, short beam shear (ILSS) and Charpy-impact tests were performed on the reference and PA 66 interleaved composite specimens. The DCB test results showed that the initiation and propagation Mode-I fracture toughness values of the composites were significantly improved by 84 and 171% using PA 66-17 gsm veils respectively, as compared to reference laminates. The use of denser PA 66-50 gsm veils in the interlaminar region led to higher improvement in fracture toughness values (349% for initiation and 718% for propagation) due to the higher amount of veil fibers involved in fiber bridging toughening mechanism. The incorporation of PA 66-50 gsm nonwoven veils also increased the ILSS and Charpy impact strength of the composites by 25 and 15%, respectively. On the other hand, the PA 66 veils reduced in-plane mechanical properties of CF/EP composites due to lower carbon fiber volume fraction and increased thickness.Article Citation - WoS: 31Citation - Scopus: 33Modification of Carbon Fibre/Epoxy Composites by Polyvinyl Alcohol (pva) Based Electrospun Nanofibres(Adcotec Ltd., 2016) Beylergil, Bertan; Tanoğlu, Metin; Aktaş, EnginIn this study, the effects of modifying interlaminar region of unidirectional carbon fibre/epoxy composites by the incorporation of electrospun polyvinyl alcohol (PVA) nanofibres were investigated. PVA nanofibres were directly deposited onto the carbon fabrics by electrospinning method to improve mechanical performance of those composites. The features of the electrospun nanofibres were characterized by microscopy techniques. The unidirectional carbon fibre/epoxy composite laminates with/without PVA nanofibre interlayers were manufactured by vacuum-infusion technique in a [0]4 configuration. Tensile, three-point bending, compression, Charpy-impact and Mode-I fracture toughness tests (Double Cantilever Beam (DCB)) were carried out in accordance with ASTM standards to evaluate mechanical performance of the composites. Scanning electron microscopy (SEM) observations were made on the specimens to evaluate microstructural features. It was observed that the carbon fabrics were successfully coated with a thin layer of PVA nanofibres by electrospinning technique. The results showed that P VA nanofibres improve the mechanical properties of unidirectional carbon/epoxy composite laminates when subjected to in-plane loading. On the other hand, PVA nanofibres slightly reduced the mode-I fracture toughness values although they led to more stable crack propagation.Article Citation - WoS: 108Citation - Scopus: 117Enhancement of Interlaminar Fracture Toughness of Carbon Fiber–epoxy Composites Using Polyamide-6,6 Electrospun Nanofibers(John Wiley and Sons Inc., 2017) Beylergil, Bertan; Tanoğlu, Metin; Aktaş, EnginIn this study, carbon fiber–epoxy composites are interleaved with electrospun polyamide-6,6 (PA 66) nanofibers to improve their Mode-I fracture toughness. These nanofibers are directly deposited onto carbon fabrics before composite manufacturing via vacuum infusion. Three-point bending, tensile, compression, interlaminar shear strength, Charpy impact, and double cantilever beam tests are performed on the reference and PA 66 interleaved specimens to evaluate the effects of PA 66 nanofibers on the mechanical properties of composites. To investigate the effect of nanofiber areal weight density (AWD), nanointerlayers with various AWD are prepared by changing the electrospinning duration. It is found that the electrospun PA 66 nanofibers are very effective in improving Mode-I toughness and impact resistance, compressive strength, flexural modulus, and strength of the composites. However, these nanofibers cause a decrease in the tensile strength of the composites. The glass-transition temperature of the composites is not affected by the addition of PA 66 nanofibers. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017, 134, 45244.Article Citation - WoS: 31Citation - Scopus: 36Mechanical Behavior of Polypropylene-Based Honeycomb-Core Composite Sandwich Structures(SAGE Publications Inc., 2010) Sezgin, Fatma Erinç; Tanoğlu, Metin; Eğilmez, Oğuz Özgür; Dönmez, CemalettinThis article presents results from an experimental study, investigating the effects of core thickness on the mechanical properties of composite sandwich structures with polypropylene(PP)-based honeycomb core and glass fiber-reinforced polymer (GFRP) face-sheets fabricated by hand lay-up technique. Epoxy matrix and non-crimp glass fibers were used for the production of GFRP laminates. Flatwise compression (FC), edgewise compression (EC), three-point bending (3PB) and double cantilever beam (DCB) tests were performed to evaluate the mechanical behavior of the composite sandwich structures (CSSs). Based on the FC tests, an increase in the compressive modulus and strength was observed with an increase in the core thickness. For EC tests, peak loads up to crush of the sandwich panel is discussed using core thickness. According to the 3PB tests, a decrease in core shear stress and facesheet bending stress was observed as the core thickness increases. © SAGE Publications 2010.Article Citation - WoS: 53Citation - Scopus: 63Artificial Neural Network (ann) Prediction of Compressive Strength of Vartm Processed Polymer Composites(Elsevier Ltd., 2005) Seyhan, Abdullah Tuğrul; Tayfur, Gökmen; Karakurt, Murat; Tanoğlu, MetinA three layer feed forward artificial neural network (ANN) model having three input neurons, one output neuron and two hidden neurons was developed to predict the ply-lay up compressive strength of VARTM processed E-glass/ polyester composites. The composites were manufactured using fabric preforms consolidated with 0, 3 and 6 wt.% of thermoplastic binder. The learning of ANN was accomplished by a backpropagation algorithm. A good agreement between the measured and the predicted values was obtained. Testing of the model was done within low average error levels of 3.28%. Furthermore, the predictions of ANN model were compared with those obtained from a multi-linear regression (MLR) model. It was found that ANN model has better predictions than MLR model for the experimental data. Also, the ANN model was subjected to a sensitivity analysis to obtain its response. As a result, the ANN model was found to have an ability to yield a desired level of ply-lay up compressive strength values for the composites processed with the addition of the thermoplastic binder.