WoS İndeksli Yayınlar Koleksiyonu / WoS Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7150
Browse
6 results
Search Results
Article Citation - WoS: 1Citation - Scopus: 2Oluklu alüminyum sandviç panellerde kor yüksekliğinin enerji sönümleme kapasitesine olan etkisi(Gazi Üniversitesi, 2020) Kılıçaslan, Cenk; Güden, MustafaIn this study, energy absorbing capacity of brazed and polyurethane adhesively bonded corrugated aluminum sandwich panels were investigated. In sandwich panels, Al 1050 H14 trapezoidal zig-zag corrugated cores and face and interlayer sheets were used. Each sandwich panel has core orientation of 0 degrees/0 degrees or 0 degrees/90 degrees. The cores used in these panels were smaller, core height is about 3 mm, in contrast to conventional sandwich cores. Impact tests were conducted at 3 and 6 m/s with spherical projectors. Adhesively bonded sandwich panels were also tested at 6 m/s with flat and conical projectors. Numerical models were prepared in LSDYNA to investigated the deformation behavior of cores. Panels tested with flat and conical projectors experienced complete perforation and absorbed more energy at configuration of 0 degrees/0 degrees core orientation. However, panels tested with spherical projectors were not perforated and they absorbed more energy at configuration of 0 degrees/90 degrees core orientation. Energy absorbing capacity of the panels were also compared to the panels having 9 mm height corrugated cores. The results showed that effective collapsing length was seen to increase due to increase in core height and impact energy distributed the whole panel surface more homogenous manner.Article Citation - WoS: 1Sol-Derived Hydroxyapatite Ddip-Coating of a Porous Ti6al4v Powder Compact(Al-Farabi Kazakh State National University, 2009) Altındiş, Mustafa; Güden, Mustafa; Ni, ChaoyingA sintered porous Ti6Al4V powder compact with a mean pore size of 63 µm and an average porosity of 37±1% was dip-coated at soaking times varying between 1- and 5-minute using a sol-derived calcium Hydrooxyapatite (HA) powder. The coated compacts were heat-treated at 840 °C. The coating thickness was found to increase with increasing soaking time, from 1.87 µm at 1-minute soaking to 9 µm at 5-minute soaking on the average. It was shown that at increasing soaking times, the originally open pores started to close, while at low soaking times the Ti6Al4V particles were partially coated. The coating layer was shown to be nano porous and the depth of coating was observed to be relatively shallow: only few particles near the compact surface were HA-coated.Article Citation - WoS: 2Citation - Scopus: 2Staphylococcus Epidermidis Adhesion on Surface-Treated Open-Cell Ti6al4v Foams(Walter de Gruyter GmbH, 2016) Türkan, Uğur; Güden, Mustafa; Sudağıdan, MertThe effect of alkali and nitric acid surface treatments on the adhesion of Staphylococcus epidermidis to the surface of 60% porous open-cell Ti6Al4V foam was investigated. The resultant surface roughness of foam particles was determined from the ground flat surfaces of thin foam specimens. Alkali treatment formed a porous, rough Na2Ti5O11 surface layer on Ti6Al4V particles, while nitric acid treatment increased the number of undulations on foam flat and particle surfaces, leading to the development of finer surface topographical features. Both surface treatments increased the nanometric-scale surface roughness of particles and the number of bacteria adhering to the surface, while the adhesion was found to be significantly higher in alkali-treated foam sample. The significant increase in the number of bacterial attachment on the alkali-treated sample was attributed to the formation of a highly porous and nanorough Na2Ti5O11 surface layer.Article Citation - WoS: 29Citation - Scopus: 32Antimicrobial Activity of Tio2-Coated Orthodontic Ceramic Brackets Against Streptococcus Mutans and Candida Albicans(Springer Verlag, 2010) Özyıldız, Figen; Güden, Mustafa; Uzel, Ataç; Karaboz, İsmail; Akil, Övünç; Bulut, H.Polycrystalline alumina ceramic orthodontic brackets were coated with anatase TiO2 film via a sol-gel dip-coating method. The surface structure morphology and composition of the films were evaluated via scanning electron microscopy, atomic force microscopy, and X-ray diffraction. The antimicrobial activity of the ceramic brackets was assessed against two oral pathogens, S. mutans and C. albicans. The results demonstrated that TiO 2-coated brackets exposed to low energy UV-A illumination efficiently reduced the populations of test microorganisms relative to the uncoated brackets. The reduction efficiencies were 98% for S. mutans ATCC 10449 and 93% for C. albicans ATCC 60193. © The Korean Society for Biotechnology and Bioengineering and Springer 2010.Article Citation - WoS: 88Citation - Scopus: 92Material Parameters of Quaternary Iii–v Semiconductors for Multilayer Mirrors at 1:55 Μm Wavelength(IOP Publishing Ltd., 1996) Güden, Mustafa; Piprek, JoachimNine quaternary (Al,Ga,In) - (P,As,Sb) semiconductor compounds lattice matched to InP are investigated theoretically. Direct bandgap, refractive index at wavelength, and thermal conductivity are calculated as a function of the composition. These material properties are important, e.g. in distributed Bragg reflectors of vertical-cavity lasers. The alloy systems AlGaAsSb, AlGaPSb and GaInPSb are found to promise better performance of those mirrors than the common InGaAsP system.Article Citation - WoS: 10Electrolysis of Mgcl2 With a Top Inserted Anode and an Mg-Pb Cathode(Springer Verlag, 1994) Güden, Mustafa; Karakaya, İshakHigh energy consumption in the production of magnesium by molten salt electrolysis is mainly due to the recombination of magnesium and chlorine. The large interelectrode distance used, in conventional techniques, to reduce the extent of ‘back reaction’, results in a significant potential drop. A laboratory cell that enables the operation with smaller interelectrode distance and easy separation of electrode products has been used to study electrolytic magnesium production. The cell features a top inserted graphite anode and a Mg-Pb alloy cathode at the bottom. Current efficiency and power consumption were determined at 690° C using a current density of 0.48 A cm−2. Experiments were performed to study the effects of MgCl2 concentration and anode-cathode distance (a.c.d.) on cell operation. Results indicated that an electrolyte containing 20% MgCl2 (equiweight NaCl:KCl and 1 % NaF) with a 3 cm a.c.d. reduced the cell voltage to 3.72 V. This value corresponds to an energy consumption of 11.3 kWh kg−1 including the refining of Mg-Pb alloy produced at the cathode. This cell performance is more energy efficient compared to conventional magnesium cells.