WoS İndeksli Yayınlar Koleksiyonu / WoS Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7150
Browse
32 results
Search Results
Now showing 1 - 10 of 32
Article Citation - WoS: 10Citation - Scopus: 12A Robot Arm Design Optimization Method by Using a Kinematic Redundancy Resolution Technique(MDPI, 2022) Maaroof, Omar W.; Dede, Mehmet İsmet Can; Aydın, LeventRedundancy resolution techniques have been widely used for the control of kinematically redundant robots. In this work, one of the redundancy resolution techniques is employed in the mechanical design optimization of a robot arm. Although the robot arm is non-redundant, the proposed method modifies robot arm kinematics by adding virtual joints to make the robot arm kinematically redundant. In the proposed method, a suitable objective function is selected to optimize the robot arm’s kinematic parameters by enhancing one or more performance indices. Then the robot arm’s end-effector is fixed at critical positions while the redundancy resolution algorithm moves its joints including the virtual joints because of the self-motion of a redundant robot. Hence, the optimum values of the virtual joints are determined, and the design of the robot arm is modified accordingly. An advantage of this method is the visualization of the changes in the manipulator’s structure during the optimization process. In this work, as a case study, a passive robotic arm that is used in a surgical robot system is considered and the task is defined as the determination of the optimum base location and the first link’s length. The results indicate the effectiveness of the proposed method.Article Citation - WoS: 7Citation - Scopus: 7Gravity Compensation of a 2r1t Mechanism With Remote Center of Motion for Minimally Invasive Transnasal Surgery Applications [article](Cambridge University Press, 2023) Aldanmaz, Ataol Behram; Ayit, Orhan; Kiper, Gökhan; Dede, Mehmet İsmet CanThis work addresses the gravity balancing of a 2R1T (2 rotations – 1 translation) mechanism with remote center of motion. A previously developed balancing solution is modified and applied to a prototype and test results are presented. The mechanism is an endoscope holder for minimally invasive transnasal pituitary gland surgery. In this surgery, the endoscope is inserted through a nostril of the patient through a natural path to the pituitary gland. During the surgery, it is vital for the manipulator to be statically balanced so that in case of a motor failure, the patient is protected against any harmful motion of the endoscope. Additionally, static balancing takes the gravitational load from the actuators and hence facilitates the control of the mechanism. The mechanism is a 2URRR-URR type parallel manipulator with three legs. The payload mass is distributed to the legs on the sides. By using counter-masses for two links of each leg, the center of mass of each leg is lumped on the proximal link which simplifies the problem to balancing of a two degree-of-freedom inverted pendulum. The two proximal links with the lumped mass are statically balanced via springs. Dynamic simulations indicate that when the mechanism is statically balanced, generated actuator torques are reduced by 93.5%. Finally, the balancing solution is implemented on the prototype of the manipulator. The tests indicate that the manipulator is statically balanced within its task space when the actuators are disconnected. When the actuators are connected, the torque requirements decrease by about 37.8% with balancing.Conference Object Digital Twin of a Servo Driver of a Servo Motor as a First Step Towards a Digital Twin of a Robot Mechanism(Springer, 2022) Küçükoğlu, Sefa Furkan; Carbone, Giuseppe; Dede, Mehmet İsmet CanDigital Twin (DT) offers us to acquire actual system’s critical information and hence, it may be possible to develop and produce more suitable systems in terms of low energy consumption and effectiveness. In this way, responsible consumption and production systems can be designed and the system’s parameters can be tuned via DT. In this study, the model of a servomotor system that is used for industrial purposes is experimentally obtained. This study consists of two steps. In the first step, within the embedded control of the system, position and velocity control loops are deactivated. Then through the servo driver, currents with sinusoidal waveforms at various frequencies are applied to the servomotor. The resultant angular velocity of the motor is monitored and recorded. The amplitude of the current is kept constant during this study. The frequency of the current, however, is increased logarithmically. By using these data, a first-order transfer function (TF) is identified for the motor model. In the second step, all control loops are activated. Consequently, the total servomotor system could be represented in a digital environment. Furthermore, the static friction issue is overcome by using a Coulomb friction model with stiction effect. Finally, several experiments are conducted and then results are compared with the digital model of the servomotor system. The results clearly show that digital model can fairly represent the physical system.Book Part Citation - WoS: 1Citation - Scopus: 1Calibration Study of a Continuously Variable Transmission System Designed for Phri(Springer, 2020) Mobedi, Emir; Dede, Mehmet Ismet CanVariable stiffness actuators (VSAs) have been used in many applications of physical human-robot interfaces (pHRI). A commonly employed design is the spring-based VSA allowing the user to regulate the output force mechanically. The main design criteria of these actuation systems are the adjustment of output force independent from the output motion, and shock absorbing. In our recent work, we implemented certain modifications on the two-cone friction drive continuously variable transmission system (CVT) so that the CVT can be employed in pHRI systems. Subsequently, the optimized prototype is developed. In this study, we introduce the prototype of this new CVT systems, and its force calibration tests. The results indicate that the manufactured CVT is capable of displaying the desired output force throughout its transmission ratio range within a tolerance.Article Citation - WoS: 31Citation - Scopus: 37Kinematic Design of a Non-Parasitic 2r1t Parallel Mechanism With Remote Center of Motion To Be Used in Minimally Invasive Surgery Applications(Elsevier Ltd., 2020) Yaşır, Abdullah; Kiper, Gökhan; Dede, Mehmet İsmet CanIn minimally invasive surgery applications, the use of robotic manipulators is becoming more and more common to enhance the precision of the operations and post-operative processes. Such operations are often performed through an incision port (a pivot point) on the patient's body. Since the end-effector (the handled surgical tool) move about the pivot point, the manipulator has to move about a remote center of motion. In this study, a 3-degrees-of-freedom parallel mechanism with 2R1T (R: rotation, T: translation) remote center of motion capability is presented for minimally invasive surgery applications. First, its kinematic structure is introduced. Then, its kinematic analysis is carried out by using a simplified kinematic model which consists of three intersecting planes. Then the dimensional design is done for the desired workspace and a simulation test is carried out to verify the kinematic formulations. Finally, the prototype of the final design is presented.Article Citation - WoS: 11Citation - Scopus: 11A New Stiffness Performance Index: Volumetric Isotropy Index(MDPI, 2019) Görgülü, İbrahimcan; Dede, Mehmet İsmet CanA new index for a precise calculation of a manipulator's stiffness isotropy is introduced. The proposed index is compared with the conventionally used stiffness isotropy index by making use of the investigation on R-CUBE manipulator. The proposed index is shown to produce relatively more precise results from which a higher number of isotropic poses are detected.Article Citation - WoS: 24Citation - Scopus: 30Time Efficient Stiffness Model Computation for a Parallel Haptic Mechanism Via the Virtual Joint Method(Elsevier, 2020) Carbone, Giuseppe; Görgülü, İbrahimcan; Dede, Mehmet İsmet CanHaptic devices are used for displaying a range of mechanical impedance values to the user. This impedance is regulated by a real-time control loop depending on the position information of the end-effector, which is usually acquired indirectly by using forward kinematics equations. Nevertheless, the kinematic model is insufficient to obtain accurate values if there are non-negligible compliant displacements. This gives a strong motivation for implementing a real-time stiffness model in the haptic control loop for improving its accuracy. Additionally, stiffness performance indices can be used at the design stage for enhancing the haptic devices impedance range within optimal design procedures. Fast solutions of a stiffness model are required for a real-time control as well as for decreasing the optimization time during a design process with a trade-off between accuracy and computational costs. In this study, we propose a computation time-efficient stiffness analysis of a parallel haptic device mechanism. The accuracy and computational costs of the proposed model are calculated and compared with a model that is obtained via a finite element method to demonstrate the effectiveness of the proposed approach with the desired real-time and accuracy performance. (C) 2019 Elsevier Ltd. All rights reserved.Conference Object Citation - Scopus: 1Structural Compliance Effects on the Accuracy and Safety of a R-Cube Haptic Device(Springer Verlag, 2019) Carbone, Giuseppe; Acinapura, Antonio; Mundo, Domenico; Görgülü, İbrahimcan; Dede, Mehmet İsmet CanThis paper addresses the contribution of structural compliance on stiffness and safety of a R-CUBE Haptic Device. Structural compliance is determined in several poses via FEM analysis and addressed by referring to local and global indices of performance. Results are also compared with evidences from experimental tests. Comparison of numerical and experimental data allows to identify and separate the contributions to the overall compliance that are due to the structural stiffness, and other contributions such as joint clearance, pose and loading conditions.Article Citation - WoS: 12Citation - Scopus: 12Geometrical Analysis of a Continuously Variable Transmission System Designed for Human-Robot Interfaces(Elsevier, 2019) Mobedi, Emir; Dede, Mehmet İsmet CanNew robotic systems are placed out of their constrained workspaces in order to work alongside humans. Consequently, these applications call for robots monitoring and regulating physical human-robot interaction. These robots’ mechanical compliance should be varied when they are in physical contact with the human or their changing environments. This compliance variation can be achieved in a variety of ways. However, one common idea is the variation of joint stiffness mechanically, electromechanically or by control. The solution presented in this paper is an electromechanical way of varying the joint stiffness. Among the electromechanical methods for varying the joint stiffness, continuously variable transmission (CVT) systems can be used in human-robot interfaces if a set of design criteria are met. These criteria include backdrivability, independent output position and stiffness variation, shock absorbing and low mass/inertia. In this paper, a novel two-cone CVT design with a double spherical transmission element is introduced by taking into account the abovementioned criteria. Additionally, design parameters are identified via carrying out a geometrical analysis of this new CVT system.Conference Object Citation - WoS: 17Citation - Scopus: 23The Arrows Project: Robotic Technologies for Underwater Archaeology(IOP Publishing Ltd., 2018) Allotta, Benedetto; Costanzi, Riccardo; Ridolfi, Alessandro; Salvetti, Ovidio; Reggiannini, Marco; Kruusmaa, Maarja; Salumäe, Taavi; Lane, David Mike; Frost, Gordon; Tsiogkas, Nikolaos; Cocco, Michele; Gualdesi, Lavinio; Lacava, Giovanni; Roig, Daniel; Gündoğdu, Hilal Tolasa; Dede, Mehmet İsmet Can; Baines, Steven; Tusa, Sebastiano; Latti, Priit; Scaradozzi, DavidThe paper summarizes the main results achieved during the three-year European FP7 ARROWS project (ARchaeological RObot systems for the Worlds Seas). ARROWS concluded at the end of August 2015 and proposed to adapt and develop low-cost Autonomous Underwater Vehicle (AUV) technologies to reduce the operational cost of typical underwater archaeological campaigns. The methodology used by ARROWS researchers identified archaeologists requirements for all the phases of a campaign. These were based on guidelines issued by the project Archaeology Advisory Group (AAG), which comprised of many European archaeologists belonging to the consortium. One of the main goals of the ARROWS project was the development of a heterogeneous team of cooperating AUVs; these comprised of prototypes developed in the project and commercially available vehicles. Three different AUVs have been built and tested at sea: MARTA, characterized by flexible hardware modularity for easy adaption of payload and propulsion systems, U-CAT, a turtle inspired bio-mimetic robot devoted to shipwreck penetration and A-Size AUV, a small light weight vehicle which is easily deployable by a single person. The project also included the development of a cleaning tool for well-known artefacts and maintenance operations. Results from the official final demonstrations of the project, held in Sicily and in Estonia during Summer 2015, are presented in the paper as an experimental proof of the validity of the developed robotic tools.