WoS İndeksli Yayınlar Koleksiyonu / WoS Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7150
Browse
34 results
Search Results
Now showing 1 - 10 of 34
Article Citation - WoS: 3Citation - Scopus: 4Terahertz Wavefront Engineering Using a Hard-Coded Metasurface(Springer, 2023) Noori, Aileen; Akyürek, Bora; Demirhan, Yasemin; Özyüzer, Lütfi; Güven, Kaan; Altan, Hakan; Aygün, GülnurDuring the past few years, coding metamaterials (MM) drew significant attention, where the far-field scattering/transmission pattern of the electromagnetic wave (particularly in the THz regime) can be encoded into a single or few-bit digitized phase-response of the metasurface, thereby enabling a full digital control. Single-bit MMs contain two types of unit cells where the phase becomes 0 and 1 (in units of ?), respectively. By arranging these unit cells into a 2D surface pattern, the THz wavefront can be shaped. In this work, a novel hard-coded metasurface was designed, fabricated, and experimentally investigated for multi-beam reflection of incident THz beam. The design employs stripe and checkerboard patterns of bilayer MM unit cells consisting of square gold patches with a polymer spacing layer from a gold backplane. Experimental and simulation results show that the incident wave in the 0.500–0.750 THz range can be reflected with > 95% efficiency in uniform amplitude and 1-bit coded phase. For the checkerboard metasurface pattern, the measured and analytically calculated reflection angle shows good agreement. The metasurface design is suitable for large-scale fabrication and can potentially be used as a template in the development of actively coded metasurfaces. © 2023, The Author(s), under exclusive licence to Springer Science+Business Media, LLC, part of Springer Nature.Article Citation - WoS: 4Citation - Scopus: 4Development of Single-Use Thin Film Electrodes Based on Zn2sno4 on In2o3:sno2 Substrates With Their Biosensing Applications(Elsevier, 2022) Yurttaş, Betül; Maral, Meltem; Erdem, Arzu; Özyüzer, LütfiDopamine (DA) has a significant impact on the emergence and treatment of certain diseases (e.g., Alzheimer's and Parkinson's diseases). Therefore, monitoring of DA is important, and using biosensors is a favorable option instead of time-consuming and expensive conventional methods. In biosensor manufacturing, thin films have become a rapidly emerging field. In this study, a non-enzymatic electrochemical biosensor based on thin film electrodes is developed for monitoring DA levels. The thin film electrodes (ZTO/ITO) are developed by deposition of Zn2SnO4 (ZTO) on In2O3:SnO2 (ITO) substrates by magnetron sputtering. 3-aminopropyltriethoxysilane (APTES) is used to modify the surface of these electrodes. Physical, optical, and structural properties of the electrodes are determined by applying surface profilometry, UV–VIS–NIR spectrophotometry, X-ray diffraction (XRD), and scanning electron microscopy (SEM) measurements. According to these measurements, it has been observed that the ZTO/ITO combination has a higher optical transmission value than the bare ITO, depending on the deposition time and the oxygen concentration used during ZTO deposition. In addition, the ITO thin film has a crystalline structure, while the ZTO thin film has an amorphous structure and both thin films have a good surface morphology. As electrochemical analysis, cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and differential pulse voltammetry (DPV) measurements are performed. As a result of CV and EIS measurements, a remarkable change (63.54%) was observed after applying APTES modification onto the surface of ZTO/ITO electrode, and the ones obtained by DPV showed successful detection of DA by APTES modified ZTO/ITO. In addition, the experiments in the presence of interferences such as ascorbic acid (AA), uric acid (UA), bovine serum albumin (BSA), and fish sperm double-stranded DNA (fsDNA) show that the electrodes can be successfully applied for voltammetric determination of DA. The detection limit of DA was estimated to be 0.013 µM in the range of DA between 0.1 and 1 µM, and sensitivity was calculated and found to be 11.057 μA μg−1 mL cm−2, which means ZTO/ITO electrodes have a good sensitivity.Article Citation - WoS: 8Citation - Scopus: 8Development of Zto/Ag Transparent Electrodes for Thin Film Solar Cells(Springer, 2022) Türkoğlu, Fulya; Köseoğlu, Hasan; Ekmekçioğlu, Merve; Cantaş, Ayten; Özdemir, Mehtap; Aygün, Gülnur; Özyüzer, LütfiThis article presents the optimization of Zinc Tin Oxide/Silver/Zinc Tin Oxide (ZTO/Ag/ZTO) multilayers to implement them in thin film solar cells as transparent electrodes. To achieve improvements on the performance of these transparent multilayers, effect of Ag and ZTO thicknesses, and position of Ag layer within the multilayer were investigated. Electrical and optical characterization of these multilayers revealed that reduced sheet resistance and improved optical transmittance can be acquired for solar cells by the optimization of thin film thicknesses and position of the Ag within the multilayer. The improvement of the electrical and optical behavior of the ZTO/Ag/ZTO structures enabled figure of merit (FoM) values up to 69.69 × 10–3 Ω−1. The performance of our multilayer electrodes was also compared with ITO and AZO electrodes. The obtained results suggest that fabricated multilayer electrodes can be a good choice for thin film solar cells.Article Citation - WoS: 6Citation - Scopus: 6Nanolitography Based on Electrospun and Etched Nanofibers(Elsevier, 2021) Noori, Aileen; Döğer, Hilal; Demirhan, Yasemin; Özdemir, Mehtap; Özyüzer, Lütfi; Aygün, Gülnur; Sağlam, ÖzgeIn this study, we propose a new type of nanolithography procedure to fabricate orderly patterned metallic nanostructures using the electrohydrodynamic method and the reactive ion etching process. The electrohydrodynamic process parameters were tuned so as to create patterning with precision, and fibers in nanoscale on silver-coated substrates. We also studied reactive ion etching with different durations on the well-patterned samples. The experiments show that applying a voltage of 400 V resulted in straight patterned fibers with a diameter of 208.7 ? 30.3 nm. The statistical analysis on scanning electron microscope (SEM) images showed a significant difference in the diameter of the fibers fabricated at 400 V compared to those at 500 V and 600 V. We also confirm that the etching process has no affect on the fiber diameter. Moreover, electron dispersive X-Ray spectrometer (EDX) results suggest that an etching duration of 7 min is sufficient to remove the silver coating that is not covered with the fibers, and protect the silver nanostructures underneath the fibers. Utilizing a lowcost nanolithography procedure, we obtain the orderly patterned silver nanostructures for possible integration into miniaturized devices.Article Citation - WoS: 2Citation - Scopus: 2In-Situ Thin Film Copper-Copper Thermocompression Bonding for Quantum Cascade Lasers(Springer, 2021) Rouhi, Sina; Özdemir, Mehtap; Ekmekçioğlu, Merve; Yiğen, Serap; Demirhan, Yasemin; Szerling, Anna; Kosiel, Kamil; Kozubal, Maciej; Kruszka, Renata; Prokaryn, Piotr; Ertuğrul, Mehmet; Reno, John L.; Aygün, Gülnur; Özyüzer, LütfiThe choice of metals, bonding conditions and interface purity are critical parameters for the performance of metal-metal bonding quality for quantum cascade lasers (QCLs). Here, we present a novel approach for the thermocompression bonding of Cu-Cu thin films on GaAs-based waveguides without having any oxide phase, contamination or impurities at the interface. We designed a hybrid system in which magnetron sputtering of Ta, thermal evaporation of Cu and Cu-Cu thermocompression bonding processes can be performed sequentially under high vacuum conditions. GaAs/Ta/Cu and Cu/Ta/GaAs structures were thermocompressionally bonded in our in-situ homebuilt bonding system by optimizing the deposition parameters and bonding conditions. The grown thin film and the obtained interfaces were characterized using x-ray diffraction (XRD), scanning electron microscopy (SEM) and energy-dispersive x-ray spectroscopy (EDX) techniques. The optimum Ta and Cu films' thicknesses were found to be about 20 nm and 500 nm, respectively. EDX analysis showed that the Ta thin film interlayer diffused into the Cu structure, providing better adhesivity and rigidity for the bonding. Additionally, no oxidation phases were detected at the interface. The best bonding quality was obtained when heated up to 430 degrees C with an applied pressure of 40 MPa during bonding process.Article Citation - WoS: 8Citation - Scopus: 8Study of Boron Doped Amorphous Silicon Lightly Hydrogenated Prepared by Dc Magnetron Sputtering for Infrared Detectors Applications(Elsevier Ltd., 2020) Ketroussi, K.; Cherfi, R.; Yahia, Seba, H.; Tata, S.; Chabane, L.; Özyüzer, Lütfi; Rahal, A.The objective of this study is to investigate the effect of boron doping concentration on the bolometric properties of lightly hydrogenated amorphous silicon doped with boron (a-Si: H(B)) films. Thin film a-Si: H(B) samples with different boron concentrations are prepared by co-sputtering of boron and silicon at relatively low hydrogen pressure. FTIR analyses show that the intensity of the characteristic peak of the substitutional boron gradually increases with the addition of boron. Increasing in boron concentration affects the bolometric properties of the lightly hydrogenated a-Si: H (B) films, including conductivity at room temperature (?RT) and thermal resistance coefficient (TCR). Indeed, when the boron concentration increases from 1.5 to 43%, ?RT increases from 1.4 10?6 to 2 10?3 ??1 cm?1 while the absolute value of TCR decreases from 3% to 8% K?1, respectively. In addition, lightly hydrogenated a-Si: H (B) films exhibit good thermal stability. We have showed in this study that lightly hydrogenated a-Si: H(B) can be considered as a potential candidate for low-cost, high-performance uncooled micro bolometers. © 2020 Elsevier B.V.Article Citation - WoS: 63Citation - Scopus: 72Ito/Au Multilayer Thin Films on Transparent Polycarbonate With Enhanced Emi Shielding Properties(Elsevier, 2020) Erdoğan, Nursev; Erden, Fuat; Astarlıoğlu, A. Taner; Özdemir, Mehtap; Özbay, Salih; Aygün, Gülnur; Özyüzer, LütfiITO/Au/ITO multilayer thin films were deposited onto polycarbonate substrate via magnetron sputtering technique without intentional heating. The deposition times of both ITO and Au layers were studied to optimize the overall transparency and conductivity. As-prepared thin films were characterized using X-ray diffraction analysis, secondary ion mass spectroscopy, scanning and transmission electron microscopy, atomic force microscopy and physical property measurement system. The optical measurement results revealed that the transmittance of the films were enhanced by increasing the gold deposition time up to 15 s. Beyond this point, further increasing the duration caused a decrease in optical transmittance. Upon optimization of the Au deposition time, the deposition duration of ITO layers was also studied to increase electromagnetic interference (EMI) shielding effectiveness (SE). Maximum EMI SE in this work was measured as 26.8 dB, yielding 99.8% power attenuation, which was verified by simulation results.Article Citation - WoS: 33Citation - Scopus: 33Characterization of Thin Film Li0.5la0.5ti1-Xalxo3 Electrolyte for All-Solid Li-Ion Batteries(Elsevier, 2018) Ulusoy, Seda; Gülen, Sena; Aygün, Gülnur; Özyüzer, Lütfi; Özdemir, MehtapSince addition of Al in Li0.5La0.5TiO3 has enhanced ionic conductivity in bulk materials, it is important to apply this material on all solid state thin film batteries. Because some of the good ionic conductors such as Lithium Phosphorus Oxynitride (LiPON) are sensitive to oxygen and moisture and their application is limited, so amorphous Li0.5La0.5Ti1−xAlxO3 (LLTAlO) is a most promising candidate because of its stability. In this study, the crystalline LLTAlO targets were prepared changing the amount of x content by conventional solid state reactions. Using these targets, lithium lanthanum titanium oxide (LLTO) thin film electrolytes were deposited on ITO/SLG substrates by radio frequency magnetron sputtering system in Ar atmosphere. The structural and compositional properties of targets and thin films were characterized by SEM, XRD, Raman spectroscopy and XPS. It was found that all targets are crystalline while the thin films are amorphous. To understand the effect of Al doping on ionic conductivity, electrical measurements were done at room temperature by AC impedance spectroscopy forming ITO/LLTAlO/Al structure like capacitor. Highest ionic conductivity result, 0.96 × 10−6 S·cm−1, is obtained from the nominal thin film composition of Li0.5La0.5Ti1−xAlxO3 (x = 0.05) at room temperature measurements. Heat treatment is also conducted to investigate to understand its effect on ionic conductivity and the structure of the thin films. It is found that ionic conductivity enhances with annealing. Also, temperature dependent ionic conductivity measurements from 298 K to 385 K are taken in order to evaluate activation energy for Li-ion conduction.Article Citation - WoS: 56Citation - Scopus: 62Cross-like terahertz metamaterial absorber for sensing applications(Springer Verlag, 2018) Sabah, Cumali; Mulla, Batuhan; Altan, Hakan; Özyüzer, LütfiIn this work, a new multiband terahertz metamaterial absorber is designed and characterised by numerical simulation method. In addition, the utilisation of the proposed absorber as a sensor is also investigated. The dielectric and thickness sensing characteristics are analysed. The proposed multiband metamaterial absorber has the ability for utilising the terahertz region up to 2 THz. According to the results, it is found that the proposed absorber is capable of sensing unknown materials and material thickness with any of its five absorption bands. The sensitivity of the proposed sensor is 6.57 GHz / unit sensitivity for dielectric sensing and 7.66GHz/μm for thickness sensing.Article Citation - WoS: 15Citation - Scopus: 17Effect of Substrate Rotation Speed and Off-Center Deposition on the Structural, Optical, and Electrical Properties of Azo Thin Films Fabricated by Dc Magnetron Sputtering(American Institute of Physics, 2018) Türkoğlu, Fulya; Aygün, Gülnur; Köseoğlu, Hasan; Özdemir, Mehtap; Zeybek, S.; Özyüzer, Lütfi; Özdemir, Mehtap; Özyüzer, Gülnur Aygün; Özyüzer, LütfiIn this study, aluminum-doped zinc oxide (AZO) thin films were deposited by DC magnetron sputtering at room temperature. The distance between the substrate and target axis, and substrate rotation speed were varied to get high quality AZO thin films. The influences of these deposition parameters on the structural, optical, and electrical properties of the fabricated films were investigated by X-ray diffraction (XRD), Raman spectroscopy, spectrophotometry, and four-point probe techniques. The overall analysis revealed that both sample position and substrate rotation speed are effective in changing the optical, structural, and electrical properties of the AZO thin films. We further observed that stress in the films can be significantly reduced by off-center deposition and rotating the sample holder during the deposition. An average transmittance above 85% in the visible range and a resistivity of 2.02 × 10-3Ω cm were obtained for the AZO films.