WoS İndeksli Yayınlar Koleksiyonu / WoS Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7150
Browse
9 results
Search Results
Now showing 1 - 9 of 9
Article Design and Performance of SiOC Foam-Silica Aerogel Composites for Hot and Cold Thermal Management Applications(Elsevier Ltd, 2025) Icin, Oyku; Vakifahmetoglu, CekdarThis study focuses on the fabrication of monolithic preceramic polymer-derived ceramic (SiOC) foam-silica aerogel composites by filling the open cells of ceramic foam with a silica aerogel solution using the sol-gel technique. The effects of different drying techniques (ambient pressure vs CO2 supercritical drying) and surface modification agents, including trimethylchlorosilane (TMCS) and hexamethyldisilazane (HMDZ), are comprehensively investigated. These factors are analyzed for their influence on the composites' morphology, porosity, chemical structure, and thermal insulation performance. The drying technique and surface modification agents are found to play a critical role in achieving a high filling ratio of silica aerogel within the composites. Pure silica aerogels exhibit specific surface areas (SSAs) reaching similar to 1120 m(2).g(-1), while the SiOC foam-silica aerogel composites demonstrate SSAs of 385-440 m(2).g(-1). Nearly all samples achieve a total porosity of similar to 93 vol%. Surface modification effectively tailors the surface properties, imparting hydrophobicity with a water contact angle of 133 degrees. Thermal conductivity at room temperature ranges between 38 and 43 mW<middle dot>m(-1)<middle dot>K-1. The potential applications of these SiOC foam-silica aerogel composites as thermal insulators are assessed under extreme thermal conditions. For instance, a 14 mm thick composite has a temperature of -27 degrees C when subjected to a cold source at -78 degrees C. Instead, when exposed directly to a butane flame (similar to 1200 degrees C), the backside of the composite recorded only similar to 57 degrees C.Article Citation - WoS: 10Citation - Scopus: 10An Efficient Method of Improving Essential Oil Retention and Sustained Release of Chitosan Films: Ultrasound-Assisted Preparation of Chitosan Composites With Surface Active Chickpea Proteins(Elsevier, 2024) Barış Kavur, Pelin; Yemenicioğlu, AhmetThis work aimed at preparing chitosan (CHI) composites with surface active chickpea protein (CP) showing better eugenol (EUG) retention and sustained release capacity than pristine CHI films. For this purpose, ionic complexation of CHI with CP (CHI:CP ratio = 2:1, w/w) in the presence of EUG at pH 5.0 was achieved using mechanical homogenization alone (HM) or in combination with ultrasonic homogenization (HM-HUS). The HM-HUS treatment provided better solubility of CP (4.4-fold), increased emulsified EUG in film-forming solutions, and denser films than HM treatment. The composite films obtained using HM-HUS (FLMCHI-CP-EUG/HM-HUS) retained 1.2–1.4-fold higher EUG after drying, and showed almost 2-fold slower EUG release in air at room temperature than composite films prepared by HM, and control CHI films prepared by HM (FLMCHI-EUG/HM) or HM-HUS (FLMCHI-EUG/HM-HUS). The FLMCHI-CP-EUG/HM-HUS films also showed better moisture barrier and mechanical properties than other films. The developed films were proved in a challenging coating application with onions. Escherichia coli and Listeria innocua counts of inoculated and FLMCHI-CP-EUG/HM-HUS (average coating thickness = 4.5 ± 1.3 μm) coated onions were significantly lower than those of uncoated (2.8 and 3.8 log) and FLMCHI/HM-HUS (1.4 and 1.3 log) coated onions after 5-days at room temperature. FLMCHI-CP-EUG/HM-HUS coating also reduced percentage of sprouted onions from 30 to 10% during storage. EUG odor of coated onions could not have been detected by 80% of panelists after 4 weeks. Compositing with CP boosts the performance of essential oil loaded CHI films by enabling use of film matrix as an encapsulant. © 2024 Elsevier LtdArticle Citation - WoS: 10Citation - Scopus: 10Comparison of the Rermineralisation Effect of a Glass Ionomer Cement Versus a Resin Composite on Dentin of Primary Teeth(Ariesdue Srl, 2014) Aykut-Yetkiner, A.; Simsek, D.; Eronat, C.; Ciftcioglu, M.Aim The aim of this study was to investigate the interaction of a high viscosity glass ionomer cement (G/C) and a composite resin with caries affected dentin and to determine the remineralization levels. Materials and Methods In a split Mouth deSign 24 GIC and composite resin atraumatic restorative treatment restorations were made in vivo and the teeth were collected after 2 years and subsequently settioned and examined using Vickers microhardness test; the latter was performed starting from the dentin surfate adjacent to the restoration. Repeated Measure ANOVA and Bonferroni Statistical methods were used for data analysis. Results The micrdhardness adjacent to the GIC reStorative material resulted tube significantly higher. Conclusion GIC resulted to be a better restorative material for the remineralization of caries affected dentin, though further studies are necessary for the corroboration of this finding. The GIC restored primary molar dentin had a higher level of remineralizatiOn and GIC could be the material of chdice in pediatric dentistry.Article Citation - WoS: 76Citation - Scopus: 95Development of Flexible Zein-Wax Composite and Zein-Fatty Acid Blend Films for Controlled Release of Lysozyme(Elsevier Ltd., 2013) Arcan, İskender; Yemenicioğlu, AhmetThe aim of this study was controlled release of lysozyme by modification of hydrophobicity and morphology of zein films using composite and blend film making methods. The incorporation of beeswax, carnauba or candelilla wax into films at 5% (w/w) of zein gave composite films containing amorphous wax particles, while incorporation of oleic acid into film at 5% of zein caused formation of blend films containing many spherical zein capsules within their matrix. The lysozyme release rates of composites reduced as the melting point of waxes increased. The composites and blends showed 2.5 to 17 fold lower lysozyme release rates than controls. The films were effectively plasticized by using catechin. The catechin also provided antioxidant activity of films (up to 69 mu mol Trolox/cm(2)) and contributed to their controlled release properties by reducing film porosity. The films showed antimicrobial activity against Listeria innocua. This work showed the possibility of obtaining advanced edible films having flexibility, antimicrobial and antioxidant activity and controlled release properties.Article Citation - WoS: 80Citation - Scopus: 107Application of Active Zein-Based Films With Controlled Release Properties To Control Listeria Monocytogenes Growth and Lipid Oxidation in Fresh Kashar Cheese(Elsevier Ltd., 2013) Uysal Ünalan, İlke; Arcan, İskender; Korel, Figen; Yemenicioğlu, AhmetThe antimicrobial and antioxidant potential of zein and zein-wax composite films having different release profiles for lysozyme and mixture of lysozyme, catechin and gallic acid were tested on cold-stored fresh Kashar cheese inoculated with Listeria monocytogenes ATCC 7644. All lysozyme containing films prevented the increase of L. monocytogenes counts in Kashar cheese for 8 weeks at 4°C, but it was only the zein-wax composite films with sustained lysozyme-release rates which caused a significant reduction (- 0.4 decimals) in initial microbial load of inoculated cheese samples. The mixture of catechin and gallic acid improved the in vitro antimicrobial effect of films against L. monocytogenes, but showed no considerable antimicrobial effect in cheese. However, the films containing catechin and gallic acid were effective in preventing oxidative changes in cheese. This study showed the possibility of increasing safety and quality of fresh cheeses by use of active packaging employing natural antimicrobial compounds and controlled release technology. Industrial relevance There has been a growing interest to develop the functional properties of packaging materials and to obtain packed foods with better shelf-life and quality. Active packaging incorporating antimicrobials is one of the most promising areas since application of this method can improve safety of foods by inhibiting pathogenic bacteria or controlling spoilage flora by using minimum amounts of active compounds. Recently, health concerns of consumers and environmental problems related to plastics increased the popularity of using natural antimicrobial substances in edible films and coatings. This work employs a GRAS status natural antimicrobial lysozyme and zein a major by-product of rapidly growing oil and bioethanol industries which can form self-standing films, coatings or casings. The results of this study showed the possibility of using flexible antimicrobial and antioxidant films with controlled release properties in diary industry.Article Citation - WoS: 22Citation - Scopus: 28Mechanical Interlocking Between Porous Electrospun Polystyrene Fibers and an Epoxy Matrix(American Chemical Society, 2014) Demir, Mustafa Muammer; Horzum, Nesrin; Taşdemirci, Alper; Turan, Ali Kıvanç; Güden, MustafaAn epoxy matrix filled with nonwoven mats of porous polystyrene (PS) fibers processed by an electrospinning was compression tested at quasi-static (1 × 10–3 s–1) and high strain (315 s–1) rates. The electrospun PS fibers with a diameter between 6 and 9 μm, accommodated spherical pores on the surface with the sizes ranging from 0.1 to 0.2 μm. The filling epoxy matrix with 0.2 wt % PS fibers increased the compressive elastic modulus and compressive strength over those of neat epoxy resin. The microscopic observations indicated that the surface pores facilitated the resin intrusions into the fiber, enhancing the interlocking between resin and fibers, and increased the deformation energy expenditure of the polymer matrix.Article Citation - WoS: 19Citation - Scopus: 21Effect of Strain Rate on the Compressive Mechanical Behavior of a Continuous Alumina Fiber Reinforced Ze41a Magnesium Alloy Based Composite(Elsevier Ltd., 2006) Güden, Mustafa; Akil, Övünç; Taşdemirci, Alper; Çiftçioğlu, Muhsin; Hall, Ian W.The compressive mechanical response of an FP™ continuous fiber (35 vol.%) Mg composite has been determined in the transverse and longitudinal directions at quasi-static and high strain rates. It was found that the composite in the transverse direction exhibited strain rate sensitivity of the flow stress and maximum stress within the studied strain-rate range of 1.3 × 10−4 to 1550 s−1. The failure strain in this direction, however, decreased with increasing strain rate. Microscopic observations on the failed samples have shown that the composite failed by shear banding along the diagonal axis, 45° to the loading axis. Twinning was observed in the deformed cross-sections of the samples particularly in and near the shear band region. The strain rate sensitivity of the fracture stress of the composite in transverse direction is attributed to the matrix strain rate sensitivity. In the longitudinal direction, the composite failed by kink formation at quasi-static strain rates, while kinking and splitting were observed at the high strain rates. The maximum stress in the longitudinal direction was, however, found to be strain rate insensitive within the strain rate regime of 1.3 × 10−4 to 500 s−1. In this direction, similar to transverse direction, twinning was observed in the highly deformed kink region. Several different reasons are proposed for the strain rate insensitive compressive strength in this direction.Article Citation - WoS: 25Citation - Scopus: 36Effect of Strain Rate on the Compression Behaviour of a Woven Fabric S2-Glass Fiber Reinforced Vinyl Ester Composite(Elsevier, 2003) Akil, Övünç; Yıldırım, Uygar; Güden, Mustafa; Hall, Ian W.Quasi-static (~10−3s−1) and high strain rate (>500 s−1) compression behavior of an S2-glass woven fabric/vinyl ester composite plate was determined in the in-plane and through-thickness directions. In both directions, modulus and failure strength increased with increasing strain rate. A higher strain rate sensitive modulus was found in the through-thickness direction while a higher strain rate sensitive failure strength was found in the in-plane direction. In the in-plane direction, the failure mode was observed to change from splitting followed by “kink banding” (localized fiber buckling) to predominantly splitting at increasing strain rates, while it remained the same in the through-thickness direction.Article Citation - WoS: 26Citation - Scopus: 40Effect of Strain Rate on the Compression Behaviour of a Woven Glass Fiber/Sc-15 Composite(Elsevier Ltd., 2004) Güden, Mustafa; Yıldırım, Uygar; Hall, Ian W.Strain rate dependent compression behavior of a plain-weave S-2 glass fabric SC-15 epoxy (rubber toughened resin) composite plate, currently studied as the backing plate for composite armor applications, was determined in the through-thickness direction (normal to the fiber plane) in the strain rate regime of 1×10−4 to 1.1×103 s−1. In the studied strain rate regime, the modulus and failure strength of the composite were found to be rate sensitive and increased with increasing strain rate. Microscopic observations showed that the composite failed by ductile failure, involving matrix cracks and, later, cracking through and between the fiber layers. Crack deflections at rubber particle/matrix interface and particle pull-out were observed in the failed samples, contributing to the toughness of the composite.