Chemical Engineering / Kimya Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/14
Browse
5 results
Search Results
Article Citation - WoS: 4Citation - Scopus: 3Modification of Surface Charge Characteristics for Unsupported Nanostructured Titania-Zirconia Uf/Nf Membrane Top Layers With Calcination Temperature(Springer, 2020) Erdem, İlker; Çiftçioğlu, MuhsinCeramic membranes are more advantageous alternatives especially for harsh working conditions when compared with the polymeric membranes. The porous multilayer structure of the ceramic membranes (composed of support, intermediate, and top layers) can be prepared via different oxides. Titania and zirconia, having superior properties, are mainly preferred for the top layer formation. The separation properties of the membrane are both dependent on pore morphology and surface charge of the oxide(s) forming the top layer. The effect of surface charge in separation may be very significant in case of filtration of charged species with relatively lower mass as in the ultrafiltration (UF) and nanofiltration (NF). In this study, unsupported membrane top layers were prepared with varying titania/zirconia ratios by sol-gel technique. Their surface charges at different pH conditions after calcination at varying temperatures (400 degrees, 500 degrees, and 600 degrees C) were determined. The surface charge of the pure titania (full Ti) top layer was decreasing with the increasing calcination temperature. The highest magnitudes of zeta potential for both acidic and basic conditions were measured via Zr rich top layer (TiZr2575) at calcination temperatures >= 500 degrees C, which was composed of anatase, rutile (titania), and tetragonal (zirconia) phases after calcination. The tailor-made top layer can be prepared with modifications during membrane preparation.Article Citation - Scopus: 2The Surface Charge of Unsupported Nano-Structured Titania Ceramic Membrane Top Layers With Varying Calcination Temperatures(University of Chemical Technology and Metallurgy, 2019) Erdem, İlker; Çiftçioğlu, MuhsinTitania is one of the most preferable ceramic membrane materials of superior durability (as zirconia) when compared to that of other ceramics, e.g. alumina or silica. The surface charge of the membrane top layer is an important parameter of the separation performance of the multilayer ceramic membrane due to the Donnan exclusion mechanisms. In this study, the change of the surface charge of unsupported nano-structured titania top layer is investigated with calcination temperature variation. The effect observed indicates the possibility of preparation of tailor-made top layers for multilayer ceramic membranes. © 2019, University of Chemical Technology and Metallurgy.Article Citation - WoS: 6Citation - Scopus: 7Influence of Calcination Temperature on Microstructure and Surface Charge of Membrane Top Layers Composed of Zirconia Nanoparticles(Springer Verlag, 2015) Erdem, İlker; Çiftçioğlu, MuhsinThe purpose of the research is to investigate the changes in microstructure and physicochemical characteristics, mainly surface charge (i.e. zeta potential) of zirconia membrane top layer during calcination. Zirconia is one of the most commonly preferred materials for ceramic membrane top layers due to its superior durability. The physicochemical properties of the top layer composed of submicron / nano particles is necessary not only for Donnan exclusion but also for dynamics of membrane fouling. In the present research the possibility of preparation of zirconia top layers with varying surface charge with changing calcination temperature was shown and a correlation between phase transformation and surface charge was determined.Conference Object Citation - WoS: 2Citation - Scopus: 2Investigation of the Permeability of Pure Gases in Sol-Gel Derived Al 2o 3 Membrane(Trans Tech Publications, 2004) Topuz, Berna; Çiftçioğlu, Muhsin; Özkan, FehimeThe preparation, characterization and pure gas permeation of sol-gel derived alumina membranes were investigated in this work. The effects of acid concentration/type and water content on the particle size in the sols and pore size distributions of the unsupported membrane were investigated by N 2 adsorption/desorption isotherms and Dynamic Light Scattering. Increasing the H +/Al 3+ mole ratio from 0.1 to 0.25 caused the hydrodynamic sol particle size and BJH pore size to decrease from 65 to 30 nm and 3.6 to 2.9 nm, respectively. The pore size increased from 2.8 nm to 3 nm upon increasing the calcination temperature from 500 to 600°C. Unsupported membranes were heat treated in the 200 to 1200 °C range for the characterization of the phase structure. Pinhole and crack free alumina membranes about 3 μm (2-layer) in thickness was observed from the SEM pictures with insignificant infiltration. The CO 2 permeability through the double layer γ-Al 2O 3 membrane calcined at 600 °C was 2.25*10 -7 mol/m 2.s.Pa, and had a slight pressure dependence indicating Knudsen Diffusion and Laminar Flow being the effective transport mechanisms. Upon the calcination of a similar 2-layer alumina membrane at 500°C, the CO 2 permeability decreased to 1.51 *10 -8 mol/m 2.s.Pa. without pressure dependence.Conference Object Citation - Scopus: 1Effects of Processing on the Properties and Permeability of Pure Gases Through Sol-Gel Silica Membranes(Trans Tech Publications, 2004) Topuz, Berna; Çiftçioğlu, Muhsin; Özkan, FehimeN2, O2 and CO2 pure gas permeation through sol-gel derived silica membranes were determined and the effects of processing parameters on the microstructure of the membrane was investigated. Silica sols were prepared in an alcoholic solution by hydrolysis and condensation of TEOS as a function of acid content. The thickness of the silica membranes was determined to be about 2μm and significant infiltration into the support was observed from the SEM pictures. The supported membranes were heat treated in the 50-400°C. The N2 permeabilities of silica membranes varied in the 2.2*10-10-2.7*10-8 mol/m2.s.Pa range for single layer membranes dipped for 10s. in the sol. The CO2 permeability of these membranes varied in the 1.2*10-9-6.95 *10-8 mol/m2.s.Pa range. The sols became viscous and gelled at 50°C in 16 hours. The O2 permeability increased with aging time. The optimum dipping time during processing was determined to be 10 seconds. The increase in the acid content of the sols were observed to increase permeabilities of the membranes significantly.