Chemical Engineering / Kimya Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/14
Browse
6 results
Search Results
Article Citation - WoS: 4Citation - Scopus: 5Breakthrough Curve Analysis of Phosphorylated Hazelnut Shell Waste in Column Operation for Continuous Harvesting of Lithium From Water(Elsevier, 2024) Recepoğlu, Yaşar Kemal; Arar, Ozguer; Yuksel, AsliIn batch-scale operations, biosorption employing phosphorylated hazelnut shell waste (FHS) revealed excellent lithium removal and recovery efficiency. Scaling up and implementing packed bed column systems necessitates further design and performance optimization. Lithium biosorption via FHS was investigated utilizing a continuous-flow packed-bed column operated under various flow rates and bed heights to remove Li to ultra-low levels and recover it. The Li biosorption capacity of the FHS column was unaffected by the bed height, however, when the flow rate was increased, the capacity of the FHS column decreased. The breakthrough time, exhaustion time, and uptake capacity of the column bed increased with increasing column bed height, whereas they decreased with increasing influent flow rate. At flow rates of 0.25, 0.5, and 1.0 mL/min, bed volumes (BVs, mL solution/mL biosorbent) at the breakthrough point were found to be 477, 369, and 347, respectively, with the required BVs for total saturation point of 941, 911, and 829, while the total capacity was calculated as 22.29, 20.07, and 17.69 mg Li/g sorbent. In the 1.0, 1.5, and 2.0 cm height columns filled with FHS, the breakthrough times were 282, 366, and 433 min, respectively, whereas the periods required for saturation were 781, 897, and 1033 min. The three conventional breakthrough models of the Thomas, Yoon-Nelson, and Modified Dose-Response (MDR) were used to properly estimate the whole breakthrough behavior of the FHS column and the characteristic model parameters. Li's extremely favorable separation utilizing FHS was evidenced by the steep S-shape of the breakthrough curves for both parameters flow rate and bed height. The reusability of FHS was demonstrated by operating the packed bed column in multi-cycle mode, with no appreciable loss in column performance.Article Citation - WoS: 10Citation - Scopus: 12Novel Hybrid Adsorption-Electrodialysis (aded) System for Removal of Boron From Geothermal Brine(American Chemical Society, 2022) Altınbaş, Bekir Fırat; Orak, Ceren; Ökten, Hatice Eser; Yüksel, AslıA novel hybrid adsorption-electrodialysis (AdED) system to remove environmentally harmful boron from geothermal brine was designed and effective operating parameters such as pH, voltage, and flow rate were studied. A cellulose-based adsorbent was synthesized from glycidyl methacrylate (GMA) grafted cellulose and modified with a boron selective n-methyl-d-glucamine (NMDG) group and characterized with SEM-EDX, FT-IR, and TGA analyses. Batch adsorption studies revealed that cellulose-based adsorbent showed a remarkable boron removal capacity (19.29 mg/g), a wide stable operating pH range (2-10), and an adsorption process that followed the Freundlich isotherm (R2= 0.95) and pseudo-second-order kinetics (R2= 0.99). In the hybrid AdED system, the optimum operating parameters for boron removal were found to be a pH of 10, a voltage of 10 V, a flow rate of 100 mL/min, and an adsorbent dosage of 4 g/L. The presence of the adsorbent in the hybrid system increased boron removal from real geothermal brine (containing 199 ppm boron) from 7.2% to 73.3%. The results indicate that the designed AdED system performs better than bare electrodialysis for boron removal from ion-rich real geothermal brine while utilizing environmentally friendly cellulose-based adsorbent.Article Citation - WoS: 13Citation - Scopus: 11Valorization of Olive Tree Pruning Waste for Potential Utilization in Lithium Recovery From Aqueous Solutions(Springer, 2022) Nampeera, Jackline; Recepoğlu, Yaşar Kemal; Yüksel, AslıOlive tree pruning waste, mainly composed of olive branches, was converted into a value-added and sustainable product capable of lithium as a biosorbent through alkali treatment and phosphorylation reaction. Characterization studies were performed by SEM–EDX, XPS, FTIR, and TGA. Factors affecting biosorption mechanism, i.e., sorbent dosage, pH, initial Li+ concentration and temperature, and competitive ions’ presence, were investigated the synthesized functionalized olive branches (FOB). A commercial lithium selective resin, Lewatit TP 260, was also compared with FOB in batch and column studies. The Freundlich model fits adsorption isotherms better than the Langmuir model, with a maximum adsorption capacity of 6.7 mg/g at 30 °C and pH 7–8. Kinetic studies proved fast kinetics and equilibrium were attained in 6 min, while thermodynamic studies showed an exothermic (Δ Ho= - 17.52 kJ/ mol) , spontaneous reaction Δ Go< 0 at all temperatures), and increased randomness Δ So= + 24.27 J/ mol. K) at the interaction interface. Column studies revealed that although Lewatit TP 260 resin showed higher sorption capacity, its desorption efficiency (50.42%) was lower than that of FOB (99.9%), and the degree of column utilization of FOB (56.81%) was better than Lewatit TP 260 resin’s (16.0%). The findings were encouraging in the successful synthesis of a promising biosorbent from an abundant waste in Turkey for use in sustainable lithium recovery from aqueous sources. Graphical abstract: [Figure not available: see fulltext.]Article Citation - WoS: 1Citation - Scopus: 1Selective Catalytic Hydrogenation of Cellulose Into Sorbitol With Ru-Based Catalysts(TÜBİTAK, 2022) Orak, Ceren; Sapmaz, Aycan; Yüksel, AslıSorbitol is one of the platform chemicals and can be produced from various renewable and sustainable sources via different processes. Hydrothermal liquefaction is an effective and promising approach to produce sorbitol, since the subcritical reaction media and appropriate catalysts provide a selective production of platform chemicals. In this study, sorbitol was produced from different renewable sources (cellulose and glucose) in the presence of Ru-based catalysts (Ru/SiO2, Ru/AC, Ru/SBA-15, and Ru/SBA-15-SO3) under subcritical conditions. The highest cellulose conversion was achieved as 90% in the presence of Ru/SBA-15-SO3 for 1 h of reaction duration. The highest sorbitol yield (%) by hydrothermal liquefaction of cellulose was obtained as 6.2% by using Ru/AC for 1 h of reaction duration. A total of 99.9% of glucose conversion was achieved in the presence of all catalysts. The highest sorbitol yield (%) by hydrothermal liquefaction of glucose was found as 3.8% for 1 h of reaction duration. Owing to the results of GC-MS analysis, the intermediate products were identified, and, thus, a reaction pathway was proposed.Article Citation - WoS: 13Citation - Scopus: 12Comparison of Photocatalytic Performances of Solar-Driven Hybrid Catalysts for Hydrogen Energy Evolution From 1,8–diazabicyclo[5.4.0]undec-7 (dbu) Solution(Elsevier, 2022) Orak, Ceren; Yüksel, AslıHydrogen is evolved from 1,8–Diazabicyclo [5.4.0]undec-7-ene (DBU) model solution which is a nitrogen-containing heterocyclic organic compound using different solar-driven hybrid photocatalysts. A characterization study is performed and the results of PL analysis show that the most promising solar-driven hybrid catalyst is graphene supported LaFeO3. Then, an experimental design matrix is built using the Box Behnken model to main and interaction effects of reaction parameters (pH, catalyst loading, and [H2O2]0). Based on the experimental results relatively higher hydrogen amounts are achieved using GLFO and this finding is supported by PL analysis. The highest hydrogen amount and DBU removal are determined as 3058.31 μmol/gcat and 90.3%, respectively. Statistical analysis shows that the square of catalyst loading is the only effective parameter over the produced hydrogen amount from the DBU model solution using GLFO and the R2 of model is 92.47%. Thus, hydrogen production and wastewater treatment could be achieved via photocatalytic oxidation as concomitant.Article Citation - WoS: 14Citation - Scopus: 12Photocatalytic Hydrogen Energy Evolution From Sugar Beet Wastewater(Wiley-VCH Verlag, 2021) Orak, Ceren; Yüksel, AslıHydrogen is a clean, environmentally friendly, storable, and sustainable green energy source as well as a potential fuel. It could be produced from various biomass, wastewater, or other sources by different processes. In this study, hydrogen was evolved from sucrose model solution and real sugar beet wastewater by photocatalytic oxidation using a perovskite catalyst under solar light irradiation. In this context, firstly, the graphene supported LaFeO3 (GLFO) was synthesized and then, a characterization study shows that GLFO is successfully synthesized. To optimize the reaction parameters (pH, catalyst loading, and initial hydrogen peroxide concentration), an experimental matrix was created using the Box Behnken model. Whereas the highest hydrogen evolution from sucrose model solution was observed as 3520 μmol/gcat, the highest hydrogen evolution from sugar beet wastewater was obtained as 7035 μmol/gcat. The highest TOC removal (99.73 %) from sugar beet wastewater was also achieved at the same reaction conditions.