Search Results

Now showing 1 - 3 of 3

Citation - WoS: 18
Citation - Scopus: 17
Modifying Pickering Polymerized High Internal Phase Emulsion Morphology by Adjusting Particle Hydrophilicity
(Elsevier, 2024) Durgut, Enes; Zhou, Muchu; Dikici, Betuel Aldemir; Foudazi, Reza; Claeyssens, Frederik
This study investigates the use of submicron polymeric particles with varying crosslinking densities as the sole stabilizer for producing Polymerized High Internal Phase Emulsions (PolyHIPE). We establish a direct correlation between the crosslinking density and the hydrophilicity of the polymer particles. The hydrophilicity of these particles significantly influences the morphology and rheology of HIPEs. These differences manifest as various morphological variations in the resulting PolyHIPE templates. It was discovered that by increasing the crosslinker weight percentage in the particles from 0 % to 100 %, PolyHIPEs with semi-open, open, and closed porous structures can be obtained. Furthermore, non-crosslinked particles were observed to dissolve in the continuous phase, acting as macromolecular surfactants that generate small pores akin to surfactant-stabilized structures in PolyHIPE. These findings offer fresh insights into the relationship between particle localization at the interface, HIPE rheology, and the formation of pore throats in Pickering PolyHIPEs, leading to the creation of either closed or open porous networks. Additionally, interfacial rheological results demonstrate that particles synthesized with varying monomer-to-crosslinker ratios exhibit different interfacial elasticities, which are linked to PolyHIPE morphology.
Citation - WoS: 14
Citation - Scopus: 16
Synergistic Effect of Type and Concentration of Surfactant and Diluting Solvent on the Morphology of Emulsion Templated Matrices Developed as Tissue Engineering Scaffolds
(Elsevier, 2022) Claeyssens, Frederik; Aldemir Dikici, Betül; Dikici, Serkan
Emulsion templating is an advantageous route for the fabrication of tissue engineering scaffolds. Emulsions are mostly stabilised using surfactants, and the performances of the surfactants depend on various parameters such as emulsification temperature and the presence of the electrolytes. In this study, we suggest that diluting solvent type also has a dramatic impact on the efficiency of the surfactant and morphology of the polymerised emulsions. For this, morphologies of polycaprolactone methacrylate-based polymerised emulsions, which are designed for tissue engineering applications and in vitro biocompatibilities, were shown by our group, prepared using four different surfactants, and three different solvents were investigated. Results showed that the diluting solvent used in the emulsion composition has a strong impact on the performance of the surfactant and consequently on the morphology of polymerised emulsions. Increasing surfactant concentration and diluting solvent volume have an opposite impact on the characteristics of emulsions. Scaffolds with average pore sizes changing from 10 to 78 μm could be fabricated. Establishing these relations enables us to have control over the overall morphology of polymerised emulsions and precisely engineer them for specific tissue engineering applications by tuning solvent and surfactant type and concentration.
Citation - WoS: 46
Citation - Scopus: 46
Thiolene- and Polycaprolactone Methacrylate-Based Polymerized High Internal Phase Emulsion (polyhipe) Scaffolds for Tissue Engineering
(American Chemical Society, 2022) Aldemir Dikici, Betül; Malayeri, Atra; Sherborne, Colin; Dikici, Serkan; Paterson, Thomas; Dew, Lindsey; Claeyssens, Frederik
Highly porous emulsion templated polymers (PolyHIPEs) provide a number of potential advantages in the fabrication of scaffolds for tissue engineering and regenerative medicine. Porosity enables cell ingrowth and nutrient diffusion within, as well as waste removal from, the scaffold. The properties offered by emulsion templating alone include the provision of high interconnected porosity, and, in combination with additive manufacturing, the opportunity to introduce controlled multiscale porosity to complex or custom structures. However, the majority of monomer systems reported for PolyHIPE preparation are unsuitable for clinical applications as they are nondegradable. Thiol-ene chemistry is a promising route to produce biodegradable photocurable PolyHIPEs for the fabrication of scaffolds using conventional or additive manufacturing methods; however, relatively little research has been reported on this approach. This study reports the groundwork to fabricate thiol- and polycaprolactone (PCL)-based PolyHIPE materials via a photoinitiated thiolene click reaction. Two different formulations, either three-arm PCL methacrylate (3PCLMA) or four-arm PCL methacrylate (4PCLMA) moieties, were used in the PolyHIPE formulation. Biocompatibility of the PolyHIPEs was investigated using human dermal fibroblasts (HDFs) and human osteosarcoma cell line (MG-63) by DNA quantification assay, and developed PolyHIPEs were shown to be capable of supporting cell attachment and viability.

Bioengineering / Biyomühendislik

Browse

Filters

Settings

Sort By

Results per page

Search Results