PubMed İndeksli Yayınlar Koleksiyonu / PubMed Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7645
Browse
6 results
Search Results
Article A Simplified Molecular Imprinting Strategy Through Electrospinning of Polyacrylonitrile for Thin Film Microextraction of Selected Pesticides(Elsevier B.V., 2026) Şahin, A.; Akpinar, Y.; Yildirim, E.; Eroǧlu, A.E.; Boyaci, E.Molecularly imprinted polymers (MIPs) have been extensively used as selective extractive phases for sample preparation because of their analyte-selective binding sites. However, MIP preparation requires optimized monomer-template interactions and long polymerization reactions. In this study, a novel and simple method of MIP preparation was proposed based on electrospinning. Instead of preparing analyte-monomer complexes before polymerization, model analytes (trifluralin and carbaryl) were directly dissolved in a polyacrylonitrile (PAN) solution, then electrospun into nanofibrous mats. This allowed for a means of preparation of highly crystalline, template-imprinted nanostructures with minimal synthetic complexity. Following the characterization studies for the new material, the extraction properties of the imprinted and nonimprinted electrospun mats were investigated in thin film microextraction (TFME) studies by extracting trifluralin and carbaryl from water samples, followed by gas chromatography-mass spectrometry (GC–MS) analysis. The optimization results showed that samplers containing 10.0 mg of MIP sorbents made by electrospinning of a solution containing 5.0 mg of template in 1.0 mL of PAN solution resulted in approximately 4 and 7 times enhanced extraction recoveries for carbaryl and trifluralin compared to samplers made of non-imprinted bulk PAN. Moreover, the cross-reactivity testing performed with non-template analytes (malathion and diazinon) suggested a more specific extraction towards trifluralin compared to carbaryl. The proposed new technique was also validated using computational methodology, which supported the experimental finding about higher selectivity towards trifluralin. This may signify a probability for structural orientation of partially charged trifluralin under an electrical field in electrospun PAN creating favorable extraction sites. © 2025 Elsevier B.V.Article Citation - WoS: 4Citation - Scopus: 4Novel Electrospun-Based Extractive Probes for Rapid Determination of Clinically Important Compounds in Human Plasma(Elsevier B.V., 2024) Temel,E.R.; Eroğlu,A.E.; Salih,B.; Boyaci,E.Background: Coated blade spray (CBS) represents an innovative approach that utilizes solid-phase microextraction principles for sampling and sample preparation. When combined with ambient mass spectrometry (MS), it can also serve as an electrospray ionization source. Therefore, it became a promising tool in analytical applications as it can significantly reduce the analysis time. However, the current CBS coatings are based on the immobilization of extractive particles in bulk polymeric glue, which constrains the diffusion of the analytes to reach the extractive phase; therefore, the full reward of the system cannot be taken at pre-equilibrium. This has sparked the notion of developing new CBS probes that exhibit enhanced kinetics. Results: With this aim, to generate a new extractive phase with improved extraction kinetics, poly(divinylbenzene) (PDVB) nanoparticles were synthesized by mini-emulsion polymerization and then immobilized into sub-micrometer (in diameter) sized polyacrylonitrile fibers which were obtained by electrospinning method. Following the optimization and characterization studies, the electrospun-coated blades were used to determine cholesterol, testosterone, and progesterone in plasma spots using the CBS-MS approach. For testosterone and progesterone, 10 ng mL−1 limits of quantification could be obtained, which was 200 ng mL−1 for cholesterol in spot-sized samples without including any pre-treatment steps to samples prior to extraction. Significance: The comparison of the initial kinetics for dip-coated and electrospun-coated CBS probes proved that the electrospinning process could enhance the extraction kinetics; therefore, it can be used for more sensitive analyses. The total analysis time with this method, from sample preparation to instrumental analysis, takes only 7 min, which suggests that the new probes are promising for fast diagnostic applications. © 2024 Elsevier B.V.Article Citation - WoS: 45Citation - Scopus: 46Electrospun Polystyrene Fibers Knitted Around Imprinted Acrylate Microspheres as Sorbent for Paraben Derivatives(Elsevier, 2018) Demirkurt, Merve; Ölçer, Yekta Arya; Demir, Mustafa Muammer; Eroğlu, Ahmet EroğluParabens are used as antimicrobial preservatives in food, cosmetic products and pharmaceuticals regardless of their endocrine disrupting effect. In this study, highly selective molecular imprinted polymers (MIPs) were synthesized in submicron-sizes and converted to an SPME fiber coating through electrospinning process in order to determine parabens in water samples. Conversion of MIP to a fiber is achieved via creation of spacial knitting around MIP by polystyrene. The selectivity and extraction ability of the fibers were compared with the commercial fibers and the corresponding non-imprinted polymer (NIP) coated fiber. The coated fiber showed better extraction ability among them. Also, the results revealed that the fiber has better selectivity for benzyl paraben and the other structurally-related compounds, such as methyl and propyl paraben. Extraction efficiency of prepared fibers for three parabens has been tested by spiking bottled, tap and sea water samples. The recoveries changed between 92.2 ± 0.8 and 99.8 ± 0.1 for three different water types. This method could be used for selective and sensitive determination of parabens in aqueous samples.Article Citation - WoS: 64Citation - Scopus: 67Hierarchically Structured Metal Oxide/Silica Nanofibers by Colloid Electrospinning(American Chemical Society, 2012) Horzum Polat, Nesrin; Mun˜oz-Espí, Rafael; Glasser, Gunnar; Demir, Mustafa Muammer; Landfester, Katharina; Crespy, DanielWe present herein a new concept for the preparation of nanofibrous metal oxides based on the simultaneous electrospinning of metal oxide precursors and silica nanoparticles. Precursor fibers are prepared by electrospinning silica nanoparticles (20 nm in diameter) dispersed in an aqueous solution of poly(acrylic acid) and metal salts. Upon calcination in air, the poly(acrylic acid) matrix is removed, the silica nanoparticles are cemented, and nanocrystalline metal oxide particles of 4-14 nm are nucleated at the surface of the silica nanoparticles. The obtained continuous silica fibers act as a structural framework for metal oxide nanoparticles and show improved mechanical integrity compared to the neat metal oxide fibers. The hierarchically nanostructured materials are promising for catalysis applications, as demonstrated by the successful degradation of a model dye in the presence of the fibers.Article Citation - WoS: 74Humidity Sensing Properties of Zno-Based Fibers by Electrospinning(Elsevier Ltd., 2011) Horzum Polat, Nesrin; Taşçıoğlu, Didem; Okur, Salih; Demir, Mustafa MuammerZinc oxide (ZnO) based fibers with a diameter of 80-100 nm were prepared by electrospinning. Polyvinyl alcohol (PVA) and zinc acetate dihydrate were dissolved in water and the polymer/salt solution was electrospun at 2.5 kV cm-1. The resulting electrospun fibers were subjected to calcination at 500 °C for 2 h to obtain ZnO-based fibers. Humidity sensing properties of the fiber mats were investigated by quartz crystal microbalance (QCM) method and electrical measurements. The adsorption kinetics under constant relative humidity (RH) between 10% and 90% were explained using Langmuir adsorption model. Results of the measurements showed that ZnO-based fibers were found to be promising candidate for humidity sensing applications at room temperature.Article Citation - WoS: 22Citation - Scopus: 28Mechanical Interlocking Between Porous Electrospun Polystyrene Fibers and an Epoxy Matrix(American Chemical Society, 2014) Demir, Mustafa Muammer; Horzum, Nesrin; Taşdemirci, Alper; Turan, Ali Kıvanç; Güden, MustafaAn epoxy matrix filled with nonwoven mats of porous polystyrene (PS) fibers processed by an electrospinning was compression tested at quasi-static (1 × 10–3 s–1) and high strain (315 s–1) rates. The electrospun PS fibers with a diameter between 6 and 9 μm, accommodated spherical pores on the surface with the sizes ranging from 0.1 to 0.2 μm. The filling epoxy matrix with 0.2 wt % PS fibers increased the compressive elastic modulus and compressive strength over those of neat epoxy resin. The microscopic observations indicated that the surface pores facilitated the resin intrusions into the fiber, enhancing the interlocking between resin and fibers, and increased the deformation energy expenditure of the polymer matrix.