Environmental Engineering / Çevre Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4321
Browse
10 results
Search Results
Article Citation - WoS: 20Citation - Scopus: 24Lime-Activated One-Part Geopolymer Mortars From Construction, Demolition and Industrial Wastes(Elsevier, 2024) Kogbara, Reginald B.; Al-Zubi, Abdelrahman; Mortada, Youssef; Hammoud, Ahmad; Masad, Eyad A.; Khraisheh, Marwan K.This work focused on the production of one-part geopolymer mortars from construction and demolition wastes (CDW) blended with steel slag. Previous related studies on geopolymer production from CDW utilized conventional two-part geopolymers comprised of highly alkaline activator solutions and CDW materials. Thus, the study's significance consists in producing high-strength (≥35 MPa) ambient-cured mortars from CDW with predominantly concrete waste by replacing conventional highly alkaline activator solutions with an environmentally-friendly alkaline activator, Ca(OH)2 powder. Four mortar mixtures were produced with CDW contents ranging from 50 to 65 % dry weight, varying the brick waste content from 3 to 18 %. The effect of elevated temperature (40 °C) curing was also considered. The results showed that 55 % CDW content had optimum performance across all parameters studied such as compressive and flexural strengths, setting time, as well as changes in nuclear magnetic resonance (NMR)-determined pore structure (porosity and mean pore size) and x-ray diffraction (XRD)-determined degree of crystallinity over time. It had 28-day compressive and flexural strengths of 42 and 5.8 MPa, respectively, and initial and final setting times of 25 and 50 min. The importance of sufficient brick waste content in the geopolymer mixtures for effective mechanical performance is highlighted. The inclusion of concrete waste in powder form reduced compressive strength under ambient curing but improved performance at 40 °C curing. It is concluded that sustainable structural mortars can be produced by ‘just adding water’ to an optimized CDW mixture with predominantly concrete waste blended with brick waste and slag and activated by powdered Ca(OH)2. © 2023 The AuthorsArticle Citation - WoS: 5Citation - Scopus: 5Screening Diatom Strains Belonging To Cyclotella Genus for Chitin Nanofiber Production Under Photobioreactor Conditions: Chitin Productivity and Characterization of Physicochemical Properties(Elsevier, 2023) Özkan, AltanDiatom species belonging to Cyclotella and Thalassiosira genera have the unique and industrially relevant ability to biosynthesize and extrude pure chitin nanofibers. The current understanding of diatom-based chitin production is narrowed by the complete reliance on the performance of a single strain. This study aims to facilitate the development of a wider understanding for enhanced industrial utility. For this purpose, six Cyclotella strains were cultivated under standardized process conditions of a bubble column photobioreactor, and the resulting productions were characterized in terms of rate and physicochemical properties. A two-stage cultivation protocol was followed where the cells were cultivated under silicon replete and then following its complete consumption under silicon deplete conditions. All the strains produced chitin fibers of β-form with relatively constant average diameters, ranging from 48 to 58 nm. Chitin production rates and final concentrations as well as fiber number densities and length distributions were highly strain-dependent. Dissolved silicon availability controlled chitin biosynthesis: following its depletion, the productivity of all the strains increased drastically. Two strains of marine origin, C. cryptica CCMP 332 and C. cryptica CCMP 333, generated the most favorable outcomes for commercial-scale production and had final concentrations of 272 ± 9 mg/L and 316 ± 12 mg/L, and maximum production rates of 48 ± 2 mg/L-day and 51 ± 2 mg/L-day, respectively. The superior performance of these strains was due to (i) the extrusion of more fibers per fiber port, in the case of C. cryptica CCMP 333 as many as 20.7 ± 1.0. indicating free fiber accumulation in suspension, and (ii) the biosynthesis of longer fibers, mean fiber lengths varied from 15 to 20 μm during cultivation. This study demonstrates the importance of species selection and silicon availability for diatom-based chitin production in terms of rate, final concentration, and nanofiber fiber length distributions.Article Citation - WoS: 31Citation - Scopus: 34Insights Into Engineered Graphitic Carbon Nitride Quantum Dots for Hazardous Contaminants Degradation in Wastewater(Elsevier, 2023) Gören, Ayşegül Yağmur; Recepoğlu, Yaşar Kemal; Vatanpour, Vahid; Yoon, Yeojoon; Khataee, AlirezaIncreased environmental pollution is a critical issue that must be addressed. Photocatalytic, adsorption, and membrane filtration methods are suitable in environmental governance because of their high selectivity, low cost, environment-friendly nature, and excellent treatment efficiency. Graphitic carbon nitride (g-C3N4) quantum dots (QDs) have been considered as photocatalysts, adsorbents, and membrane materials for wastewater treatments, owing to their stability, adsorption capacity, photochemical properties, and low toxicity and cost. This review summarizes g-C3N4 QD synthesis techniques, operating parameters affecting the removal performance in the treatment process, modification effects with other semiconductors, and benefits and drawbacks of g-C3N4 QD-based materials. Furthermore, this review discusses the practical applications of g-C3N4 QDs as adsorbents, photocatalysts, and membrane materials for organic and inorganic contaminant treatments and their value-added product formation potential. Modified g-C3N4 QD-based material adsorbents, photocatalysts, and membranes present potentially applicable effects, such as removal of most waterborne contaminants. Excellent results were obtained for the reduction of methyl orange, bisphenol A, tetracycline, ciprofloxacin, phenol, rhodamine B, E. coli, and Hg. Overall, this paper provides comprehensive background on g-C3N4 QD-based materials and their diverse applications in wastewater treatment, and it presents a foundation for the enhancement of similar unique materials in the future.Article Citation - WoS: 11Citation - Scopus: 12Investigation of the Best Possible Methods for Wind Turbine Blade Waste Management by Using Gis and Fahp: Turkey Case(Springer, 2022) Öztürk, Samet; Karipoğlu, FatihThe aim of this study is to present the status and projections of wind turbine blade retirement in Turkey; to investigate the number of retiring WT blades in the regional, manufacturer, and material aspects; and to discuss the management methods for retired WT blades. To determine the best possible wind turbine blade waste management methods for Turkey, a combined application of Geographical Information Systems (GIS) and the Fuzzy Analytical Hierarchy Process (FAHP) is used in this study. It is found that around nine thousand WT blades will become waste between 2020 and 2039 in Turkey, corresponding to around 80,500 tons of waste. On average, 52,325 tons of glass/carbon and 28,175 tons of polymers will be accumulated between 2020 and 2039 from wind turbine blades. More than half of the WT blade waste will come from two WT manufacturers, namely, Enercon and Nordex. Aegean and Marmara regions will provide 74% of the blade waste, where 33% of them will be 2 MW and 2.5 MW sizes of WT blades. Furthermore, a case study is applied to Izmir city to demonstrate the results of FAHP for finding the best available method to dispose of WT blades. The results show that using blade waste as filling material is the best alternative, while waste-to-energy is the last favorable option for blade waste management. Finally, sensitivity analyses are applied to demonstrate the robustness of the results for the inclusion of new alternatives and the bias of experts’ judgments.Article Citation - WoS: 10Citation - Scopus: 14Indoor Environmental Quality in Naturally Ventilated Schools of a Dusty Region: Excess Health Risks and Effect of Heating and Desert Dust Transport(Wiley, 2022) Şahin, Çağrı; Rastgeldi Doğan, Tuba; Yıldız, Melek; Sofuoğlu, Sait CemilIndoor air quality (IAQ) is impacted by polluted outdoor air in naturally ventilated schools, especially in places where both anthropogenic and natural sources of ambient air pollution exist. CO2, PM2.5, PM10, temperature, relative humidity (RH), and noise were measured in five naturally ventilated primary schools in City of Sanliurfa, in a dusty region of Turkey, Southeast Anatolia. Excess risk levels were estimated for particulate matter. Investigation was conducted through an educational year including two seasons in terms of anthropogenic effect, that is, heating/non-heating, and natural effect, that is, desert dust transport/non-dust transport. The median CO2 concentration was measured to be >1000 ppm in all seasons/schools. Temperature and RH fell out of the comfort zone in October-December, during which pollutant concentrations were considerably increased, specifically in November, that heating and dust transport periods coincide. The overall mean indoor PM10 and PM2.5 levels were 58 and 31.8 mu g/m(3), respectively. Risk assessment indicate that both short (incidence of asthma symptoms in asthmatic children) and long-term (prevalence of bronchitis) effects are considerable with 10.9 (2.4-19.6)% and 19.5 (2.2-38.8)%, respectively. The findings suggest that mechanical ventilation retrofitting with particle filtration is needed to mitigate potential negative health consequences on children.Article Citation - WoS: 7Citation - Scopus: 93d Electrode Use in Mdc for Enhanced Removal of Boron From Geothermal Water(Elsevier, 2022) Gören, Ayşegül Yağmur; Ökten, Hatice EserMicrobial desalination cell (MDC) is a significantly promising technology due to its simultaneous features of electricity production, wastewater treatment and desalination. In this paper, the three-dimensional (3D) sponge with activated carbon-chitosan (AC-CS) was synthesized to enhance the efficiency of the MDC system. Effects of operating parameters (boron concentration, electrode surface area, catholyte solution, and activated sludge volume) on MDC performance were also investigated. The MDC with 3D AC-CS anode provided a higher power density of 970 mW/m2, boron removal efficiency of 75.9%, and COD removal efficiency of >90% under optimized conditions. The maximum boron and COD removal efficiencies were 65.6 and 81.4% with the power density of 866.9 mW/m2 for geothermal brine. Moreover, BET analysis showed that the 3D AC-CS anode presented high surface area (230 m2/g) and pore volume (0.202 cm3/g). As an overall result, not only the production of 3D sponge anode electrodes with AC-CS composite was achieved but also desalination and power generation results that were comparable with the literature were presented.Article Citation - WoS: 32Citation - Scopus: 36A Review of Boron Removal From Aqueous Solution Using Carbon-Based Materials: an Assessment of Health Risks(Elsevier, 2022) Gören, Ayşegül Yağmur; Recepoğlu, Yaşar Kemal; Karagündüz, Ahmet; Khataee, Alireza; Yoon, YeojoonCarbon-based compounds have gained attention of researchers for use in boron removal due to their properties, which make them a viable and low cost adsorbent with a high availability, as well as environmental friendliness and high removal efficiency. The removal of boron utilizing carbon-based materials, including activated carbon (AC), graphene oxide (GO), and carbon nanotubes (CNTs), is extensively reviewed in this paper. The effects of the operating conditions, kinetics, isotherm models, and removal methods are also elaborated. The impact of the modification of the lifetime of carbon-based materials has also been explored. Compared to unmodified carbon based materials, modified materials have a significantly higher boron adsorption capability. It has been observed that adding various elements to carbon-based materials improves their surface area, functional groups, and pore volume. Tartaric acid, one of these doped elements, has been employed to successfully improve the boron removal and adsorption capabilities of materials. An assessment of the health risk posed to humans by boron in treated water utilizing carbon-based materials was performed to better understand the performance of materials in real-world applications. Furthermore, the boron removal effectiveness of carbon-based materials was evalu ated, as well as any shortcomings, future perspectives, and gaps in the literature.Article Citation - WoS: 9Citation - Scopus: 9How Does Arsenic Speciation (arsenite and Arsenate) in Groundwater Affect the Performance of an Aerated Electrocoagulation Reactor and Human Health Risk?(Elsevier, 2022) Gören, Ayşegül Yağmur; Kobya, Mehmet; Khataee, AlirezaArsenic (As) occurrence in water resources has become one of the most critical environmental problems worldwide. The detrimental health impacts on humans have been reported due to the consumption of As-contaminated groundwater resources. Consumption of As-containing water over the long term can cause arsenicosis and chronic effects on human health due to its toxicity. Several treatment processes are available for As removals such as coagulation, ion exchange, adsorption, and membrane technologies but they have various major drawbacks. In the present work, therefore, an aerated electrocoagulation (EC) system with aluminum anodes was operated for simultaneous arsenate (As(V)) and arsenite (As(III)) removal to overcome the disadvantages of other processes such as, sludge formation, difficulties in operation, high operating costs, high energy consumption, and the requirement of pre-treatment process and to enhance the conventional EC process. The combined effects of the applied current (0.075–0.3 A), aeration rate (0–6 L/min), pH (6.5–8.5), and As speciation (As(V)-As(III)) were studied on As removal efficiency. The findings revealed that As removal mostly depended on the airflow rate and the applied current in the EC system. The highest As removal efficiency (99.1%) was obtained at an airflow rate of 6 L/min, a pH of 6.5, an initial As (V) concentration of 200 μg/L, and a current of 0.3 A, with an energy consumption of 2.85 kWh/m3 and an operating cost of 0.66 $/m3. The human health risk assessment of treated water was also examined to understand the performance of the EC system. At most of the experimental runs, the chronic toxic risk (CTR) and carcinogenic risk (CR) of As were within the permissible limits except for an airflow rate of 0–2 L/min, an initial pH of 8.5, and a current of 0.075–0.15 A for high initial As (III) concentrations. Overall, the As removal performance and groundwater risk assessment show that the EC process is a promising option for industrial applications.Article Citation - WoS: 36Citation - Scopus: 40Land Deformation and Sinkhole Occurrence in Response To the Fluctuations of Groundwater Storage: an Integrated Assessment of Grace Gravity Measurements, Icesat/Icesat-2 Altimetry Data, and Hydrologic Models(Taylor & Francis, 2021) Khorrami, Behnam; Arık, Fetullah; Gündüz, OrhanUncontrolled extraction of water from groundwater aquifers causes groundwater depletion, which in turn triggers the formation of sinkholes in many parts of the world. Monitoring and detection of these geomorphologic features are of utmost importance and priority for the decision-makers to minimize significant environmental as well as socio-economic implications of land deformation. In this study, a systematic approach is proposed to investigate the spatio-temporal associations of groundwater storage changes with sinkhole evolution and land deformation by using a number of remotely sensed and modeled data as well as in-situ observations. The proposed approach is implemented and tested in Konya Closed Basin (KCB), Turkey, which is one of the most critical areas in central Turkey concerning sinkhole formation. The results of GRACE (Gravity Recovery and Climate Experiment) estimates suggest that there is a descending trend in the temporal variations of TWSA (Terrestrial Water Storage Anomalies) and GWSA (Groundwater Storage Anomalies) over KCB with an average storage depletion of 4.12 ± 0.34 cm/yr and 3.40 ± 0.61 cm/yr, respectively. The analysis of land deformation from ICESat/ICESat-2 (Ice, Cloud, and Land Elevation Satellite) altimetry data also indicates a descending trend with an estimated average vertical displacement of 5 cm/yr for the study area, which seems to be in rational accord with the sinkhole evolution over KCB. The results further suggest that the sinkhole evolution over KCB has an acceptable association with the variations of groundwater storage, groundwater use, and precipitation.Article Citation - WoS: 15Citation - Scopus: 18Simultaneous Energy Production, Boron and Cod Removal Using a Novel Microbial Desalination Cell(Elsevier, 2021) Gören, Ayşegül Yağmur; Ökten, Hatice EserThis paper investigates simultaneous boron removal from aqueous solutions, organic matter removal from industrial wastewater and energy production using a Microbial Desalination Cell (MDC). Anode chamber of the conventional MDC cell was modified to include 3D cubic electrodes as a novel design. Effects of operating parameters, including electrode type (3D-electrode and 2D-electrode), anolyte solution temperature (20 °C, 40 °C, and 60 °C), and activated sludge:wastewater volumetric ratio (S:WW = 1:1, 1:2, and 1:5), on MDC performance were studied. Furthermore, real geothermal water treatment was investigated under optimum operating conditions. Boron and organic matter removal efficiencies and the produced power density results were promising for 3D-electrodes under optimum operating conditions. The maximum boron removal efficiency, COD removal efficiency, and power density were 55.5%, 91.5%, and 9.04 mW/m3 treating real geothermal water at optimum operating conditions. The analyses of Scanning Electron Microscope with Energy Dispersive X-ray spectrometer (SEM-EDX) demonstrated biofilm formation and salt deposition on membrane surfaces, which most probably reduced the performance of MDC. Consequently, our results showed that use of 3D-electrodes was a promising improvement to the conventional configurations with 2-D electrodes since removal efficiencies and energy production were comparable for a more compact electrode structure.